Chief CM2-SK6 Bedienungsanleitung

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief CM2-SK6 (4 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
S E R V I C E M A N U A L
Maintenance
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
CM2-SK6
CM2-SK6 Service Manual
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
TOOLS FOR INSTALLATION / PARTS
1/8" (included)
3/16" (included)
A (1)
[Lube Grease]
B (2)
1/4-20 x 1"
C (2)
1/4"
D (1)
1/8"
E (1)
3/16"
F (1)
[Brush]
Service Manual CM2-SK6
3
LUBRICATION
1. Fully extend CM2. (See Figure 1)
2. Remove two Phillips screws and lock washers securing
cable guide side cover. (See Figure 1)
Figure 1
3. Slide cable guide side cover away from mount and carefully
set aside. (See Figure 1)
4. Lubricate the length of the threaded shaft using a liberal
amount of lube grease (A) on the applicator brush (F).
5. Replace cable guide side cover.
6. Fasten side cover to CM2 using two 1/4-20 x 1" Phillips cap
head screws (B) and two 1/4" lock washers (C). (See
Figure 1)
DRIVE BELT TENSION ADJUSTMENT
Drive belt tension is preset at the factory and should not need
adjustment during initial mount installation or operation.
However, after extended use it may be necessary to make
minor adjustments to belt tension.
NOTE: If during operation the lift moves slower than normal or
is not raising and lowering smoothly or making unusual
noise, belt tension may need to be adjusted.
WARNING: OVERTENSIONING CAN LEAD TO DAMAGE
TO EQUIPMENT! DO NOT overtension! Adjust drive belt
tension in small increments.
To adjust belt tension, turn the adjustment screw located on the
lower back side of the mount using a 3/16" hex wrench. (See
Figure 2)
1. Turn the screw clockwise to increase drive belt tension.
2. Turn the screw counter-clockwise to decrease drive belt
tension.
3. Insert screwdriver into deflection checking window and
check tension. Deflection should be approximately 1/8".
Figure 2
x 2
1
Cable guide
side cover
2
3
(front view)
(B) x 2
6
(C) x 2
Deflection
testing
window
1
2
3

Produktspezifikationen

Marke: Chief
Kategorie: niet gecategoriseerd
Modell: CM2-SK6

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chief CM2-SK6 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung niet gecategoriseerd Chief

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung für -Kategorien-