Celestron PowerSeeker 80AZ Bedienungsanleitung

Celestron Teleskop PowerSeeker 80AZ

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Celestron PowerSeeker 80AZ (4 Seiten) in der Kategorie Teleskop. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
ENGLISH | 1
Unpack your telescope and verify that all parts are present. Your
PowerSeeker 80AZS includes: an optical tube with two threaded
mounting bolts, a tripod with center support bracket, two eyepieces,
a 3x Barlow lens, a nderscope, an erect image diagonal, and an
eyepiece accessory tray.
Check to ensure that all three legs are the same height once
extended to provide a level platform for the telescope.
Locate the optical tube and insert the attached slow motion control
rod into the hole on the mount.
To set up the tripod, spread the legs outward until they are fully
extended and push down center leg brace.
Place the eyepiece accessory tray on top of the tripod’s center leg
brace. Thread the tray into the threaded hole in the center of the leg
brace until it is fully seated.
Extend the center portion of each of the three tripod legs down about
6 to 12 inches. Use the tightening screw on each leg to secure the
extended leg in place.
If necessary, rotate the accessory tray counterclockwise until
the accessory holes are not covered by the leg brace arms as
shown here.
Line up the tube with the holes on the mount and secure the tube
to the mount using the two threaded mounting bolts. Tighten to
secure in place.
#21087
ENGLISH
80AZS
Remove the knurled nuts on the threaded posts at the focuser end
of the telescope tube.
2 | ENGLISH
Insert the barrel of the 20mm eyepiece into the diagonal and tighten
the set screw, being careful not to overtighten.
Remove the lens cap from the front of the telescope. To observe, look
through the eyepiece as shown above. Focus the image by turning
the knobs below the focuser.
Locate the diagonal and remove the plastic covers. Insert the barrel
of the diagonal into the focuser and secure in place by tightening
the set screws.
Locate the finderscope and remove plastic caps on front and back of
lens. Orient the finderscope so that the longer lens is facing towards
the front of the tube as shown here. Place finderscope over the posts
on the tube and replace knurled nuts to secure.
Loosen the screws on the focuser so they do not obstruct the
inner diameter of the focuser. Remove the plastic cap covering the
end of the focuser.
For additional magnification, you can use the included 3x Barlow
lens. Place the Barlow lens in the diagonal in place of the eyepiece.
Remove the cap from the Barlow.
Next, insert the barrel of the 20mm eyepiece into the Barlow and
tighten the set screws to secure it in place.
For more information on this product or to download
the instruction manual, please visit the respective
product page on celestron.com
SOLAR WARNING: Never attempt to view the sun
through any telescope without a proper solar filter.
NEED ASSISTANCE?
Contact Celestron Technical Support
celestron.com/pages/technical-support
11-19
ENGLISH | 3
The nder is one of the most important parts of your telescope. It helps you
locate objects and center them in the eyepiece. The fi rst time you assemble your
telescope, you need to align the fi nder to the telescope’s main optics. It’s best to
do this during the day*.
* SOLAR WARNING! Never attempt to view the sun through any telescope
without a proper solar fi lter!
ALIGNING THE
FINDERSCOPE
CHOOSE A TARGET
Take the telescope outside during the day and nd an
easily recognizable object, like a streetlight, license
plate or sign. The object should be as far away as
possible, but at least a quarter mile away.
STOP
CENTER THE TARGET
IN THE EYEPIECE
Look through the telescope using your lower powered
20mm eyepiece. Move the telescope until the object
you chose lies in the center of the view. If the image is
blurry, gently turn the focus knobs on either side of the
telescope until it comes into sharp focus.
NOTE: The image in your telescope may appear
inverted. This is perfectly normal in an
astronomical telescope.
LOOK THROUGH FINDERSCOPE
Once the object is centered in your 20mm eyepiece,
look through the finderscope and locate the
crosshair reticle.
ADJUST THE FINDERSCOPE
Without moving the telescope, use the three nger
knobs surrounding in the nderscope bracket to move
the nder around until the crosshair appears over the
same object you are observing in the telescopes
20mm eyepiece.
TIP: Try adjusting one screw at a time. Loosen
one screw by half a turn and tighten
another by the same amount to ensure the
nderscope is securely held in place.
YOUR FINDERSCOPE IS
NOW ALIGNED!
It should not require realignment unless it is bumped
or dropped.
20mm Eyepiece
Focus Knobs


Produktspezifikationen

Marke: Celestron
Kategorie: Teleskop
Modell: PowerSeeker 80AZ

Brauchst du Hilfe?

Wenn Sie Hilfe mit Celestron PowerSeeker 80AZ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Teleskop Celestron

Bedienungsanleitung Teleskop

Neueste Bedienungsanleitung für -Kategorien-