Casio W-734-2AVEF Bedienungsanleitung

Casio Sportuhr W-734-2AVEF

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Casio W-734-2AVEF (5 Seiten) in der Kategorie Sportuhr. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/5

Operation Guide 3283

MO1806-EC

About This Manual

• Depending on the model of your watch, display text

appears either as dark figures on a light background or

light figures on a dark background. All sample displays

in this manual are shown using dark figures on a light

background.

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

(Light)

E-1

Contents

General Guide .........................................................................................................E-4

Timekeeping ............................................................................................................E-6

Stopwatch ................................................................................................................E-8

Recall Mode ...........................................................................................................E-18

Countdown Timer .................................................................................................. E-22

Alarms ....................................................................................................................E-25

Dual Time ............................................................................................................... E-32

Illumination ............................................................................................................E-33

Reference ..............................................................................................................E-36

Specifications .......................................................................................................E-43

E-2

Procedure Lookup

The following is a handy reference list of all the operational procedures contained in

this manual.

To set the time and date ......................................................................................... E-6

To measure times with the stopwatch ................................................................E-10

To configure your basic data ............................................................................... E-15

To turn the pacer signal on and off .....................................................................E-17

To recall stopwatch records ................................................................................ E-18

To delete a log .......................................................................................................E-21

To reset the cumulative total screen ...................................................................E-21

To set the countdown start time ..........................................................................E-22

To use the countdown timer ................................................................................E-23

E-3

To turn auto-repeat on and off ............................................................................. E-24

To set an alarm time .............................................................................................E-26

To test the alarm ................................................................................................... E-28

To select the operation of Alarm

....................................................................... E-29

To turn Alarms

through

on and off .............................................................. E-30

To turn the hourly time signal on and off ........................................................... E-31

To set the Dual Time ............................................................................................. E-32

To turn on illumination manually .........................................................................E-33

To turn the auto light switch on and off ..............................................................E-35

E-4

Press .C

General Guide

• Press C to change from mode to mode.

• In any mode, press L to illuminate the display.

Timekeeping Mode

▲

E-5

Stopwatch Mode

Dual Time Mode Alarm Mode Countdown Timer Mode

Recall Mode

▲

E-6

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Day of week

Month – Day

HourSeconds 12/24-Hour

Format

Day Month Year

Minutes

Hour : Minutes Seconds

PM indicator

Year

E-7

4. Press A to exit the setting screen.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all modes.

• The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

Setting

Seconds

Hour, Minutes

12/24-Hour

Format

Year, Month, Day

Button Operation

Press .D to reset to 00

Use D B (+) and (–) to change the setting.

Press D to toggle between 12-hour (12H) and

24-hour ( ) timekeeping.24H

Use D B (+) and (–) to change the setting.

Screen

3. When the setting you want to change is flashing, use D B and to change it as

described below.

E-8

Stopwatch

The 1/100-second stopwatch can measure elapsed time

and lap/split times. The stopwatch uses the basic data you

input and a pacer signal to calculate the distance you

cover while jogging or running. Stopwatch times and your

distance are also stored in memory.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a lap/split time is

frozen on the display clears the lap/split time and returns

to elapsed time measurement.

• Stopwatch measurements are performed in the

Stopwatch Mode, which you enter by pressing C (page

E-5).

Timekeeping Mode time

1/100 second

Seconds

Hours

Minutes

Remaining memory

E-9

How the Stopwatch Works

There are two ways you can use the stopwatch: to measure elapsed time and lap/split

times like a standard stopwatch (see “To measure times with the stopwatch” (page

E-10)), and to keep track of the distance you cover while jogging or running. In order

to use the stopwatch to keep track of distance, you must first perform the steps listed

below.

1. Set your basic data. See “Basic Data” on page E-12.

2. Turn on the pacer signal. See “To turn the pacer signal on and off” on page E-17.

Note

• In order to obtain accurate distance calculations, you must set accurate basic data

and keep your exercise pace in accordance with the pacer signal emitted by the

watch.

• See page E-40 for information about the type of data the watch stores in memory

when you use the stopwatch.

• Use the Recall Mode (page E-18) to view data stored in memory.

• You can view distance covered data only by recalling it in the Recall Mode. It does

not appear on the Stopwatch Mode screen.

Operation Guide 3283

E-10

To measure times with the stopwatch

Note

• Pressing D to perform a lap/split time operation freezes the lap/split time at that

point on the display for about eight seconds. After that, the display returns to normal

stopwatch time measurement.

• During a stopwatch time measurement operation, the upper part of the display

shows the current lap/split number and the hour digit, the center part shows the

current split time, and the lower part shows the current lap time.

• When the pacer signal is turned on, it sounds for the first 30 seconds after you start

a stopwatch time measurement operation. After that, the pacer signal sounds for 30

seconds whenever you press A.

➤➤➤➤

ClearNext Lap/

Split

➤

Start Stop

Elapsed Time

Re-start Clear

Stop

B B D

Lap/Split Times

Start Lap/Split

Stop

D B ➤D

➤➤

E-11

• If the pacer signal does not sound even though you have it turned on, press toA

change the positions of the lap time and split time on the display. This should cause

the pacer signal to sound.

Selecting the Stopwatch Screen Format

The following shows how you can control the position of the lap time and split time on

the stopwatch screen.

• The Lap/Split indicator uses arrows to indicate the location the lap time and split

(elapsed) time.

Lap/Split number

Split time Lap time Split time

More than 10 hours

Press .A

Lap time Hours

Minutes

Seconds

Lap/Split

indicator

➤

E-12

• When you first start a stopwatch operation by pressing B, both the center part and

the lower part of the display show minutes, seconds, and 1/100 second. Whenever

the time shown in the lower part of the display is greater than 60 minutes, the

display format changes to show hours, minutes, and seconds. Whenever the time in

the center part of the display is greater than 10 hours, the display format changes to

show hours, minutes, and seconds.

Basic Data

The term “basic data” refers to the pacer signal setup, and information about your

stride length.

Important!

• You cannot change basic data settings while a Stopwatch Mode time measurement

operation is in progress. Stopwatch operation must be stopped and the Stopwatch

screen must be cleared to all zeros before you can change basic data settings.

• Whenever you want to change the stride length unit, you must first reset the

Cumulative Total screen to zero. See page E-21 for information about how to do this.

• Be sure to update basic data values whenever the person using the watch changes.

E-13

Pacer Signal

The pacer signal of this watch beeps in accordance with a pacer value (rate) set by

you. You can use the pacer signal to maintain a constant pace while jogging or

running. You can also turn off the pacer signal when you do not want to use it.

• The pacer value you set specifies the number of beeps per minute.

• Turning on the pacer signal causes the watch to beep at the rate specified by the

pacer value.

• You can set a pacer value in the range of 100 to 200 beats per minute, in units of 5.

• You can disable the pacer function by setting a pacer value of . While the pacerxxx

value is set to , the watch does not calculate distance covered.xxx

Stride Length

You can specify either centimeters ( ) as the stride length unit. TheXM) or inches (Yn

unit you specify for the stride length unit also determines the unit of measurement

used for the distance value in the Stopwatch Mode and Recall Mode, as shown below.

E-14

Setting Range

40 to 190 cm

16 to 76 in

Setting Increment

5 cm

2 in

Distance Unit

Kilometers (km)

Miles (mi)

• The following examples illustrate how you can calculate values for this setting.

239 steps required to run around a 300-meter track.

300 (meters)

239 (steps) = 1.255 (approximately 125 cm)

239 steps required to run around a 330-yard track.

330 (yards)

239 (steps)

36 = 49.70 (approximately 50 inches)

Stride Length Unit

Centimeters (XM)

Inches (Yn)

E-15

To configure your basic data

1. While the Stopwatch Mode screen shows all zeros

( 0 H00'00 00'' ), hold down A until the pacer value

appears flashing on the display. This indicates the

setting screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

3. When the setting you want to change is flashing, use

D B and to change it as described below.

Stride length unit

Pacer value Pacer signal

Stride length

E-16

Setting

Pacer value

Pacer signal

Stride length

Stride length unit

Screen Button Operations

Use D B (+) and (–) to change the setting.

• Selecting xxx disables the pacer signal.

Press )D to toggle the pacer signal on (ON

and off (OFF).

Use D B (+) and (–) to change the setting.

Press )D to toggle between centimeters (XM

and inches (Yn).

• When the pacer signal is turned on, the pacer signal sounds in accordance with the

pacer value while the pacer signal or pacer value setting screen is on the display.

4. Press A to exit the setting screen.

• If you find that the stride length unit won’t change, reset the cumulative total to all

zeros (page E-21).

E-17

To turn the pacer signal on and off

1. While the Stopwatch Mode screen shows all zeros

( 0 H00'00 00'' ), hold down A until the pacer value

appears flashing on the display. This indicates the

setting screen.

2. Press C once to display the pacer signal setting

screen.

3. Press D to toggle the pacer signal on (ON) and off

(OFF).

• A pacer signal on indicator ( ) appears when this

setting is turned on.

4. Press A to exit the setting screen.

E-18

Recall Mode

Use the Recall Mode to recall and delete records stored

by the Stopwatch Mode.

• Stopwatch records are stored in “logs” that are created

automatically by the watch. See “Memory Management”

(page E-38) for more information.

• The title screen of the newest log appears first whenever

you enter the Recall Mode.

• Log numbers are automatically assigned in sequence,

starting from 01.

• All of the operations in this section are performed in the

Recall Mode, which you enter by pressing C (page E-5).

To recall stopwatch records

In the Recall Mode, use A to scroll through the log title

screens, starting from the newest one, as shown below.

When the title screen of the log you want is displayed, use

D B and to cycle through the records contained in the log.

Distance covered

Log number Creation date

(Month – Day)

Log Title Screen

E-19

• The cumulative total screen shows the total distance since the last cumulative total

distance reset (page E-21).

Press .B

▲

Press D.

Split time

Lap/Split number

BEST indicator

▲

Cumulative Total Screen

▲

Press .A

Log Title Screen

Stopwatch Record

Screen

Best Lap Time

Screen

Lap time

▲

Operation Guide 3283

E-20

• The locations of the lap time and split time (middle or bottom of the display) in the

Stopwatch Record screen are determined by the display format you last selected in

the Stopwatch Mode (page E-11).

• The BEST indicator identifies the record that contains the best lap time in the log.

• If a best lap time record is deleted automatically when the log becomes full, the

BEST indicator will not be transferred to the record with the next best lap time. See

“Memory Management” (page E-38) for more information about automatic deletion

of records.

• The unit of measurement used for the distance calculation depends on the unit you

select for your stride length as shown in the table below. See “To configure your

basic data” (page E-15) for more information.

Selected Stride Unit Distance Unit

XM (centimeters) km (kilometers)

Yn (inches) mi (miles)

E-21

To delete a log

1. In the Recall Mode, display the title screen of the log you want to delete.

• See “To reset the cumulative total screen” below for information about what

happens when you select the cumulative total screen here.

2. Hold down B and D until the watch beeps and CLR stops flashing on the

display.

• This deletes the log and all the records inside it. Deleting a log does not change the

cumulative total distance value.

To reset the cumulative total screen

1. In the Recall Mode, display the cumulative total screen.

2. Hold down B and D until the watch beeps and CLR stops flashing on the

display.

• This resets the cumulative total distance to zero, without deleting any logs or

records. A new cumulative total will start with the next stopwatch operation you

perform.

E-22

Countdown Timer

You can set the countdown timer within a range of one

minute to 100 hours. An alarm sounds when the

countdown reaches zero.

• You can also select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• Countdown timer functions are available in the

Countdown Timer Mode, which you can enter using C

(page E-5).

To set the countdown start time

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the hour

setting of the countdown start time starts to flash, which

indicates the setting screen.

Hours

Minutes

Seconds

Timekeeping Mode time

E-23

• If the countdown start time is not displayed, use the procedure under “To use the

countdown timer” to display it.

2. Press C to move the flashing between the hour and minute settings.

3. Use D (+) and B (–) to change the flashing item.

• To set the starting value of the countdown time to 100 hours, set 0:00.

4. Press A to exit the setting screen.

To use the countdown timer

Press B while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is automatically reset to its starting value when the alarm sounds.

• Press B while a countdown operation is in progress to pause it. Press B again to

resume the countdown.

• To completely stop a countdown operation, first pause it (by pressing B), and then

press D. This returns the countdown time to its starting value.

E-24

To turn auto-repeat on and off

While the countdown start time is displayed on the

Countdown Timer Mode screen, hold down ' for about

two seconds to toggle auto-repeat on ( displayed) and

off ( not displayed).

• When auto-repeat is turned on, the alarm sounds and

countdown starts again whenever the countdown

reaches zero. You can stop the countdown by pressing

%, and manually reset to the countdown start time by

pressing '.

• Auto-repeat timing repeats up to eight times.

Auto repeat on indicator

E-25

Alarms

You can set five independent Daily Alarms. When an

alarm is turned on, the alarm tone sounds when the alarm

time is reached. One of the alarms can be configured as a

snooze alarm or a one-time alarm, while the other four are

one-time alarms.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

• There are five alarm screens numbered 1 5 through .

The hourly time signal screen is indicated by :00.

• All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C (page E-5).

Alarm number

Alarm time

(Hour : Minutes)

Timekeeping Mode time

E-26

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2

through 5 can be used as one-time alarms only.

• The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash. This indicates the setting screen.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D (+) and B (–) to change it.

x1 x2

:00 x5

E-27

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. (P indicator).

5. Press A to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds. In the case of the snooze

alarm, the alarm operation is performed a total of seven times, every five minutes, until

you turn the alarm off or change it to a one-time alarm (page E-29).

E-28

Note

• Pressing any button stops the alarm tone operation.

• Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen (page E-6)

Displaying the Alarm

setting screen (page E-26)

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

E-29

To select the operation of Alarm

1. In the Alarm Mode, use to select AlarmD1.

2. Press B to cycle through the available settings in the sequence shown below.

• The applicable alarm on indicator is displayed in all modes when an alarm is turned

on.

• The SNZ indicator flashes during the 5-minute intervals between alarms.

• Displaying the Alarm 1 setting screen (page E-26) while the snooze alarm is turned

on automatically turns off the snooze alarm (making Alarm1 a one-time alarm).

Snooze alarm on indicator and alarm on indicator

One-time alarm on Snooze alarm on Alarm off

Produktspezifikationen

Marke:	Casio
Kategorie:	Sportuhr
Modell:	W-734-2AVEF
Bandmaterial:	Harz
Wasserfest:	Ja
Timer:	1/1 min. - 100 h
Kalender:	Ja
Stoppuhr:	Ja
Gewicht:	38 g
Produktfarbe:	Blau
Akku-/Batterietyp:	CR2025
Material des Uhrengehäuses:	Harz
Abmessungen (BxTxH):	42.4 x 13.9 x 48.2 mm
Wasserdicht bis Tiefe:	100 m
Akkurazität:	30 Sek/Monat