Casio PRW-1300T-7VER Bedienungsanleitung

Casio Sportuhr PRW-1300T-7VER

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Casio PRW-1300T-7VER (15 Seiten) in der Kategorie Sportuhr. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/15

Operation Guide 3070 (B)

MO0805-EC

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out

of your purchase, be sure to read this manual carefully.

Applications

The built-in sensors of this watch measure direction, barometric pressure,

temperature and altitude. Measured values are then shown on the display.

Such features make this watch useful when hiking, mountain climbing, or

when engaging in other such outdoor activities.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the

watch is stored by a built-in battery. Leaving or

using the watch where it is not exposed to light

causes the battery to run down. Make sure the

watch is exposed to light as much as possible.

• When you are not wearing the watch on your

wrist, position the face so it is pointed at a

source of bright light.

• You should try to keep the watch outside of

your sleeve as much as possible. Charging is

reduced significantly if the face is covered only

partially.

Bright light

Solar cell

• The watch continues to operate, even when it is not exposed to light.

Leaving the watch in the dark can cause the battery to run down, which will

cause some watch functions to be disabled. If the battery goes dead, you

will have to re-configure watch settings after recharging. To ensure normal

watch operation, be sure to keep it exposed to light as much as possible.

Bright light

Electrical

energy

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Solar cell

(Converts light to

electrical power.)

Rechargeable battery

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving

function has turned off the display to conserve power.

• See “Power Saving” for more information.

Warning!

• The measurement functions built into this watch are not intended for

taking measurements that require professional or industrial precision.

Values produced by this watch should be considered as reasonable

representations only.

• When engaging in mountain climbing or other activities in which losing

your way can create a dangerous or life-threatening situation, always be

sure to use a second compass to confirm direction readings.

• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss,

or any claims by third parties that may arise through the use of this

watch.

About This Manual

• Depending on the model of your watch, display

text appears either as dark figures on a light

background, or light figures on a dark

background. All sample displays in this manual

are shown using dark figures on a light

background.

• Button operations are indicated using the

letters shown in the illustration.

• Each section of this manual provides you with

the information you need to perform operations

in each mode. Further details and technical

information can be found in the “Reference”

section.

(Light)

General Guide

• The illustration below shows which buttons you need to press to navigate

between modes.

• In any mode, press L to illuminate the display.

• You can use buttons , and to enter a sensor mode directly fromA, B C

the Timekeeping Mode or from another sensor mode. To enter a sensor

mode from the Data Recall, World Time, Stopwatch, Countdown Timer,

Alarm, or Receive Mode, first enter the Timekeeping Mode and then press

the applicable button.

Timekeeping Mode

Altimeter Mode

World Time

Mode

Data Recall

Mode

Digital

Compass Mode

Press D.

▲

Press .B

Countdown

Timer Mode

Press D.

▲

Press C.

▲

Sensor Modes

Stopwatch Mode

Barometer/

Thermometer Mode

Press .A

Alarm Mode

▲

Receive Mode

▲

• The actual level at which some functions are disabled depends on the

watch model.

• Frequent display illumination can run down the battery quickly and require

charging. The following guidelines give an idea of the charging time

required to recover from a single illumination operation.

Approximately five minutes exposure to bright sunlight coming in through

a window

Approximately 50 minutes exposure to indoor fluorescent lighting

• Be sure to read “Power Supply” for important information you need to

know when exposing the watch to bright light.

Operation Guide 3070 (B)

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting

accordingly.

• This watch is designed to pick up the time calibration signals transmitted in

Germany (Mainflingen), England (Anthorn), and the United States (Fort

Collins) and the time calibration signals transmitted in Japan.

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time

calibration signal. You also can perform a manual procedure to set the time

and date, when necessary.

• The first thing you should do after purchasing this watch is to specify

your Home City (the city where you normally will use the watch). For

more information, see “To specify your Home City” below.

• When using the watch outside the areas covered by the time signal

transmitters, you will have to adjust the current time setting manually as

required. See

“Timekeeping” for more information about manual time

settings.

• The U.S. time calibration signal can be picked up by the watch while in

North America. The term “North America” in this manual refers to the area

that consists of Canada, the continental United States, and Mexico.

To specify your Home City

1. In the Timekeeping Mode, hold down untilE

the city code starts to flash, which indicates

the setting screen.

2. Press A (east) and C (west) to select the

city code you want to use as your Home City.

LON : London

PAR, BER : Paris, Berlin, Milan, Rome,

Amsterdam, Hamburg, Frankfurt,

Vienna, Barcelona, Madrid

ATH : Athens

TYO SEL, : Tokyo, Seoul

NYC :New York, Detroit, Miami, Boston, Montreal

CHI :

Chicago, Houston, Dallas/Fort Worth, New Orleans, Winnipeg, Mexico City

DEN :Denver, El Paso, Edmonton, Culiacan

City code Hour : Minutes

indicator Seconds

LAX :Los Angeles, San Francisco, Las Vegas, Seattle/Tacoma,

Vancouver, Tijuana

3. Press E to exit the setting screen.

• Normally, your watch should show the correct time as soon as you select

your Home City code. If it does not, it should adjust automatically after the

next auto receive operation (in the middle of the night). You also can

perform manual receive or you can set the time manually.

• The watch will receive the time calibration signal automatically from the

applicable transmitter (in the middle of the night) and update its settings

accordingly. For information about the relationship between city codes and

transmitters, see “Time Calibration Signal Reception” and “Transmitters”.

• See the maps under “Approximate Reception Ranges” for information about

the reception ranges of the watch.

• You can disable time signal reception, if you want. See “To turn auto receive

on and off” for more information.

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration

signal: auto receive and manual receive.

• Auto Receive

With auto receive, the watch receives the time calibration signal automatically

up to six times a day. When any auto receive is successful, the remaining

auto receive operations are not performed. For more information, see “About

Auto Receive”.

• Manual Receive

Manual receive lets you start a time calibration receive operation with the press

of a button. For more information, see “To perform manual receive”.

Important!

• When getting ready to receive the time calibration signal, position the watch

as shown in the nearby illustration, with its 12 o’clock side facing towards a

window. Make sure there are no metal objects nearby.

12 o’clock

• Make sure the watch is facing the right way.

• Proper signal reception can be difficult or even impossible under the

conditions listed below.

Inside or

among

buildings

Inside a

vehicle

Near a

construction

site, airport,

or other

sources of

electrical

noise

Near high-

tension

power lines

Among or

behind

mountains

Near

household

appliances,

office

equipment,

or a mobile

phone

• Signal reception normally is better at night than during the day.

• Time calibration signal reception takes from two to seven minutes, but in

some cases it can take as long as 14 minutes. Take care that you do not

perform any button operations or move the watch during this time.

• The time calibration signal the watch will attempt to pick up depends on its

current Home City code setting as shown below.

Home City Code

LON,

PAR , BER, ATH

TYO, SEL

NYC CHI DEN LAX, , ,

Frequency

60.0 kHz

77.5 kHz

40.0 kHz

60.0 kHz

Transmitter

Anthorn (England)

Mainflingen (Germany)

Fukushima (Japan)

Fukuoka/Saga (Japan)

Fort Collins, Colorado

(the United States)

• Signal reception may not be possible at the distances noted below during

certain times of the year or day. Radio interference may also cause

problems with reception.

Mainflingen (Germany) or Anthorn (England) transmitters: 500

kilometers (310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310

miles)

• Even when the watch is within the reception range of the transmitter, signal

reception will be impossible if the signal is blocked by mountains or other

geological formations between the watch and signal source.

• Signal reception is affected by weather, atmospheric conditions, and

seasonal changes.

• See the information under “Signal Reception Troubleshooting” if you

experience problems with time calibration signal reception.

About Auto Receive

The watch receives the time calibration signal automatically up to six times a

day. When any auto receive is successful, the remaining auto receive

operations are not performed. The reception schedule (calibration times)

depends on your currently selected Home City, and whether standard time or

Daylight Saving Time is selected for your Home City.

Your Home City Auto Receive Start Times

1 2 3 4 5 6

LON Standard Time

1:00 am 2:00 am 3:00 am 4:00 am 5:00 am Midnight

Daylight Saving Time

2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am

PAR Standard Time

2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am

BER

Daylight Saving Time

3:00 am 4:00 am 5:00 am Midnight 1:00 am

2:00 am

ATH Standard Time

3:00 am 4:00 am 5:00 am Midnight 1:00 am

2:00 am

Daylight Saving Time

4:00 am 5:00 am Midnight 1:00 am

2:00 am

3:00 am

TYO Standard Time

Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

SEL

NYC Standard Time and

Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

CHI

Daylight Saving Time

DEN

LAX

*Next day

Note

• When a calibration time is reached, the watch will receive the calibration

signal only if it is in either the Timekeeping Mode or World Time Mode.

Reception is not performed if a calibration time is reached while you are

configuring settings.

• Auto receive of the calibration signal is designed to be performed early in

the morning, while you sleep (provided that the Timekeeping Mode time is

set correctly). Before going to bed for the night, remove the watch from your

wrist, and put it in a location where it can receive the signal easily.

Approximate Reception Ranges

Anthorn

Mainflingen

1,500 kilometers

500 kilometers Fort

Collins

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

1,000

kilometers

1,000

kilometers

Fukuoka/Saga

500

kilometers

Fukushima

500

kilometers

Operation Guide 3070 (B)

• The watch receives the calibration signal for two to seven minutes everyday

when the time in the Timekeeping Mode reaches each of the calibration

times. Do not perform any button operation within seven minutes before or

after any one of the calibration times. Doing so can interfere with correct

calibration.

• Remember that reception of the calibration signal depends on the current

time in the Timekeeping Mode. The receive operation will be performed

whenever the display shows any one of the calibration times, regardless of

whether or not the displayed time actually is the correct time.

About the Receiving Indicator

The receiving indicator shows the strength of the calibration signal being

received. For best reception, be sure to keep the watch in a location where

signal strength is strongest. The receiving indicator is displayed while an auto

or manual receive operation is in progress.

• Even in an area where signal strength is strong, it takes about 10 seconds

for signal reception to stabilize enough for the receiving indicator to indicate

signal strength.

Receiving

indicator

Weak

(Level 1)

Strong

(Level 5)

• Use the receiving indicator as a guide for checking signal strength and for

finding the best location for the watch during signal receive operations.

• Following reception of the time calibration signal and calibration of the

watch’s time setting, the Level 5 receiving indicator will remain on the

display in all modes. The Level 5 receiving indicator will not be displayed if

signal reception was unsuccessful or after you adjust the current time

setting manually.

• The Level 5 receiving indicator is displayed only when the watch is able to

receive both time and date data successfully. It does not appear when only

time data is received.

• The Level 5 receiving indicator indicates that at least one of the auto

calibration signal receive operations was successful. Note, however, that

the Level 5 receiving indicator disappears from the display each day when

the first auto receive operation of the day is performed.

To perform manual receive

1. Enter the Receive Mode.

2. Place the watch on a stable surface so its 12

o’clock side is facing towards a window.

3. Hold down for about two seconds until ARC

starts to flash on the display.

• Time calibration signal reception takes from

two to seven minutes. Take care that you do not

perform any button operations or move the

watch during this time.

• If the receive operation is successful, the

reception date and time appear on the display,

along with the GET indicator.

The watch will enter the Receive Mode if you

press or if you do not perform any buttonA

operation for about one or two minutes.

Receiving

Receive successful

• If the current reception fails but a previous

reception was successful, the display shows

the previous reception’s date and time, and the

ERR indicator. indicates that none of

the reception operations were successful.

The watch will enter the Receive Mode without

changing the time setting if you press or ifA

you do not perform any button operation for

about one or two minutes.

Note

• To interrupt a receive operation and return to

the Receive Mode, press A.

Receive failed

If there was a previously

successful reception

If no reception was

successful

To turn auto receive on and off

1. Enter the Receive Mode.

2. In the Receive Mode, hold down until theE

current auto receive setting (ON OFF or )

starts to flash. This is the setting screen.

• Note that the setting screen will not appear

if the currently selected Home City is one

that does not support time calibration

reception.

3. Press A to toggle auto receive on (ON) and

off (OFF).

4. Press E to exit the setting screen.

• For information about city codes that support

signal receive, see To specify your Home“

City”.

On/Off

status

To check the latest signal reception results

Enter the Receive Mode.

• When receive is successful, the display shows

the time and date that receive was successful.

indicates that none of the reception

operations were successful.

• To return to the Timekeeping Mode, press D.

Signal Reception Troubleshooting

Check the following points whenever you experience problems with signal

reception.

• The watch is not in the Receive

Mode.

• Your current Home City is not

one of the following: LON, PAR,

BER, ATH, TYO, SEL, NYC,

CHI DEN, , or LAX

• You changed the time setting

manually.

• The DST setting was changed

manually in the World Time

Mode.

•

You pressed a button while signal

receive was in progress.

•

Even if receive is successful, the

Level 5 receiving indicator

disappears from the display

each day when the first auto

receive operation of the day is

performed.

•

Time data (hour, minutes,

seconds) only was received

during the last receive operation.

The Level 5 receiving indicator

appears only when time data

and date data (year, month, day)

are both received.

Cannot perform

manual receive.

Auto receive is

turned on, but

the Level 5

receiving

indicator does

not appear on

the display.

• Enter the Receive Mode

and try again.

• Select , , LON PAR BER,

ATH, TYO, SEL, NYC,

CHI DEN, , or LAX as

your Home City.

• Perform manual signal

receive or wait until the

next auto signal receive

operation is performed.

• Check to make sure the

watch is in a location

where it can receive the

signal.

What you should doProblem Probable Cause

• If the time is one hour off, the

DST setting may be incorrect.

• The Home City code setting is

not correct for the area where

you are using the watch.

• Change the DST setting

to Auto DST.

• Select the correct Home

City code.

Time setting is

incorrect

following signal

reception.

• For further information, see “ ”Important! under Time Calibration Signal“

Reception” and “Radio-controlled Atomic Timekeeping Precautions”.

Digital Compass

A built-in bearing sensor detects magnetic north and indicates one of 16

directions on the display. Direction readings are performed in the Digital

Compass Mode.

You can store a direction reading in Bearing Memory and display that reading

as you take subsequent readings.

• For more information about Bearing Memory, see “ ”Bearing Memory .

• You can calibrate the bearing sensor if you suspect the direction reading is

incorrect.

• See “Using the Digital Compass While Mountain Climbing or Hiking” for

some real-life examples of how to use this feature.

Produktspezifikationen

Marke:	Casio
Kategorie:	Sportuhr
Modell:	PRW-1300T-7VER
Bandmaterial:	Titan
Wasserfest:	Ja
Schutzfunktion:	Wasserfest
Uhrmodus:	12 h / 24 h
Timer:	Ja
Elektronischer Kompass:	Ja
Barometrischer Höhenmesser:	Ja
Eingebautes Abstand Messinstrument:	Nein
Wecker:	Ja
Kalender:	Ja
Stoppuhr:	Ja
Barometer:	Ja
Gewicht:	97 g
Produktfarbe:	Schwarz, Silber
Akku-/Batterietyp:	CTL1616
Material des Uhrengehäuses:	Harz
Abmessungen (BxTxH):	47.4 x 11.5 x 56.9 mm
Wasserdicht bis Tiefe:	100 m
Maximale Timer-Zeit:	24 h
Weltzeitfunktion:	Ja
Wasserdicht bis:	100 m
Solarenergie:	Ja
Dauer des Timers (min.):	60 s