Caple AVE2/BS Bedienungsanleitung

Caple Wasserhahn AVE2/BS

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Caple AVE2/BS (3 Seiten) in der Kategorie Wasserhahn. Dieser Bedienungsanleitung war für 68 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Customer care helpline: 0117 938 1900

www.caple.co.uk

AVE L COLOU RE D,STAI NL ES S STE EL TA P

C A R E , I NS TAL L ATIO N AN D GU AR AN T E E IN FO RM ATION

MO DEL CO DE: AVE 2/ GD A VE2/ CO , AVE2/ GM , A VE2/ BS , AVE2 / BK & AVE2/ S S

2INSTALLATION GUI DE AVE2/CO, AVE2/GM, AVE2/BS, AVE2/BK & AVE2/SS Please keep this instruction manual for future reference

5 bar

70˚ C

I NS TA L L ATI O N G U I DE

Thank you for p urchasing your Caple tap.

These taps have been manufactured and inspected to exacting standards and are guaranteed to give years of trouble

free operation providing our care and installation guidelines have been followed.

NOTE: Please see back page for installation instructions

1213

16 17

20 21

24 25

17 16

1312

4INSTALLATION GUIDE AVE2/CO, AVE2/GM, AVE2/BS, AVE2/ BK & AVE2/SS Please keep this instruction manual for future reference

GUA RA NTEE

-Your Caple tap is guaranteed for 5 years.

- Should you have any defects as detailed above during the appropriate guarantee period we guarantee to repair or replace

the defective products or parts, or, at our option refund the purchase price assuming we were advised immediately of any

claim in writing.

- It is important that you keep a proof of purchase (such as your receipt) to facilitate your guarantee.

INSTA L L ATION I N S TR UCTIONS

- Turn the spout and body so the tap is facing forwards, the

screw on the spout indicates the rear of the body. The hot

water connection should be on the left of the tap.

- Ensure the hot and cold pipes are thoroughly ﬂushed to remove

any debris.

- A 35mm hole is required in either the sink or worktop.

- The ﬁxing bolt must be screwed into the tap base, ensuring the

threads of the bolt are not damaged in the process.

- Pass the nylon washer over the ﬁxing bolt ﬂush to the bottom

of the tap base, then pass the bolt through the sink or worktop

(ensuring the nylon washer remains directly under the tap

base).

- Pass the rubber washer and then the metal washer (on the

underside of the sink/worktop) over the ﬁxing bolt and ﬁx using

the ﬁxing nut.

- Screw the ﬂexi-tail pipes into the base of the tap, ensuring the

pipes threads are not damaged in the process. If the ﬂexi-tails

are already inserted into the tap base, please ensure these are

screwed in tightly to prevent any leaks.

- Finally connect the ﬂexi-tail pipes to the hot and cold supplies

ensuring they are connected to the correct supplies.

C ARE O F YO UR TAP S

- Only clean your taps with soap or mild liquid detergent and

clean water then dry using a soft cloth

- Do not use chemical cleaners, or bleach based

solutions to clean your tap, contact could affect the ﬁnish of

your tap.

- Do not use abrasive cleaners, liquids, powders or pads. These

will damage the ﬁnish of your tap and void the guarantee.

- Provided all of the above points are adhered to the surface

ﬁnish of your Caple Tap is guaranteed for 5 years.

PRE I N S TAL L ATION CH ECK S

- The temperature of the hot water supply must not

exceed 70°C.

- Water pressure requirements: minimum required pressure

varies dependent on model, maximum pressure 5 bar.

- Always seek advice from a qualiﬁed installer to ensure your

installation and water supply to your taps comply with the

water regulation (WRAS) requirements and good plumbing

practice.

- It is good practice to ensure that both hot and cold water

supplies to your tap are of an equal pressure to provide a

consistent ﬂow. If supplies are not of equal pressure then a

non return valve should be ﬁtted on the hot inlet.

- Supplies of water should be from a common source (mains or

tank fed).

- We recommend that a service valve is installed in the

supply lines to the tap to enable water isolation if required.

POS T IN S TALL ATIO N P OINTS

- We suggest when connecting screw connections that PTFE tape

is used before the joints are fully tightened.

- Before use correctly check the installation for leaks, and

turn the hot and cold water on to thoroughly ﬂush any

small particles that may have been dislodged during the tap

installation.

THES E INSTRUC TIONS ARE INTENDE D AS A GU IDE,

IF IN ANY D OUBT ENSURE YOU SEEK ADVICE

FROM A CERTIFIED PLUMBER.

TER MS AND CO N D ITI O NS

- Guarantee conditions are only valid if the Care guidelines listed above are followed.

- Our obligation under the guarantee is to the original purchaser, and may not be transferred.

- The guarantee is valid for UK domestic installations only and relates to defects in manufacture, materials and

workmanship only.

- Issues that arise due to normal wear and tear (for example valves, discs or washers), poor installation,

improper use or accidental damage are not covered by the Caple guarantee. Spare parts can be purchased

from our Customer care helpline 0117 938 1900.

- No liability is accepted for consequential damage to other household ﬁxtures, ﬁttings or furnishings relating

to any claim - even if attached to the product.

- If it is more economically viable a replacement tap will be supplied, this tap might vary from the original

design should range changes of occurred since the initial supply.

- We reserve the right to inspect any tap before committing to support under the guarantee conditions.

Produktspezifikationen

Marke:	Caple
Kategorie:	Wasserhahn
Modell:	AVE2/BS
Produktfarbe:	Schwarz
Minimaler Wasserdruck:	50 kPa
Schwenkbar:	Ja
Swivel Winkel:	360 °
Wasserdurchflusskontrolle:	Drehventile
Anzahl Ventile/Hebel:	Doppel
Ausgusstyp:	Herunterziehen
Wasserströmungsmodi:	Stream