Caliber RDN575BT Bedienungsanleitung
Caliber
Autoradios
RDN575BT
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Caliber RDN575BT (10 Seiten) in der Kategorie Autoradios. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/10
Remove the Old Unit from the Dashboard
DIN Front Mount
DO NOT DISCONNECT WIRES
AT THIS TIME!
2. Insert the keys supplied with the
old unit into both sides of the unit
as shown in figure below until
they click. Pull to remove the old
unit from the dashboard.
1. Remove the outer trim frame.
INSTALLATION
Tools for Installation
Use the 2 removal wrenches of the old unit to take out the old unit and place with this brand new car radio. The following tools and sup-
plies may also be needed for the installation:
Tools for Installation: Philips Screw-drivers /Machine Screws /Wire Stripper /Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill
Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for Power Connections /14-16 Gauge Speaker Wires
The above are not supplied.
Before you install
Automotive audio equipment installations can be challenging even to the most experienced of installation technicians. We strongly rec-
ommend that this unit should be professionally installed by a VAT registered installer (this is a requirement to validate the warranty).
IMPORTANT: Remove the two transport screws from the top fo the unit before installing.
Mark Polarity of the Speaker Wires
Marking the polarity of the speaker wirers will make it easier to connect the existing speakers to your car radio. Consult wiring diagram
of existing head unit before disconnecting any wires. If you are not positive of the polarity of the existing wires from the speakers to the
head unit, install new wires.
1. While the old unit is playing, disconnect the wires from one speaker.
2. Take a length of masking tape and fold it around the wire so it forms a flag.
3. On the masking tape mark the polarity of the speaker wires (+&-), as well as left or right, and front or rear.
4. Double check that you marked the first speaker correctly by checking that the speaker wires are the same at the head unit.
5. Repeat this procedure for all of the speakers.
6. Mark the power, ground, and any other wires also.
Produktspezifikationen
| Marke: | Caliber |
| Kategorie: | Autoradios |
| Modell: | RDN575BT |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Caliber RDN575BT benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autoradios Caliber
13 Juli 2024
8 Oktober 2022
Bedienungsanleitung Autoradios
- Autoradios Clatronic
- Autoradios Medion
- Autoradios Philips
- Autoradios SilverCrest
- Autoradios Sony
- Autoradios Panasonic
- Autoradios AEG
- Autoradios Denver
- Autoradios ECG
- Autoradios MarQuant
- Autoradios Renkforce
- Autoradios Trevi
- Autoradios Blaupunkt
- Autoradios Grundig
- Autoradios Kenwood
- Autoradios Aiwa
- Autoradios Lenco
- Autoradios Pioneer
- Autoradios JVC
- Autoradios Krüger And Matz
- Autoradios Muse
- Autoradios Dual
- Autoradios Hyundai
- Autoradios MT Logic
- Autoradios Varta
- Autoradios Nikkei
- Autoradios XOMAX
- Autoradios Parrot
- Autoradios Alpine
- Autoradios Volvo
- Autoradios Pure
- Autoradios Clarion
- Autoradios Peiying
- Autoradios Roadstar
- Autoradios Tokaï
- Autoradios Autovision
- Autoradios Boss
- Autoradios Mini
- Autoradios Soundstream
- Autoradios Farenheit
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
11 Oktober 2024
10 Oktober 2024
9 Oktober 2024
9 Oktober 2024