Burley Cub 1996-2003 Bedienungsanleitung

Burley Diversen Cub 1996-2003

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Burley Cub 1996-2003 (12 Seiten) in der Kategorie Diversen. Dieser Bedienungsanleitung war fĂĽr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
Burley-CubTM
Owner’s Instruction & Safety Manual
Contents
Section Page
Introduction 2
I. Hardware Bag Contents & Tool List 3
II. Attaching the Wheels 3
III. Installing the Tongue & Safety Flag 5
IV. Unfolding & Folding Your Burley-Cub 6
V. Using the Seat Harness 8
VI. Covers 9
VII. Hitching the Burley-Cub to Your Bicycle 10
VIII. Trailer Maintenance & Care 12
IX. Safety Guidelines 14
X. Safety Checklists 20
XI. Parts List & Drawing 22
Warranty 24
About Burley Design Cooperative
Burley has been supplying products to the bicycle industry since 1975.
Burley products are designed and manufactured at our Eugene,
Oregon shop. As worker-owners of our cooperatively owned business,
we bring an uncommon degree of personal pride and attention to our
work. Use our products with confidence and satisfaction!
Burley Trailer Limited Warranty
Burley will repair or replace any original equipment parts it
determines to be defective for the life of the trailer. The owner
of a Burley trailer must present the trailer for repair at an
authorized Burley dealer, together with an original sales
receipt or similar proof of purchase. This warranty applies only
to the original owner and is nontransferable. Burley cannot be
responsible for failure due to improper assembly, modification
of parts or instructions, neglect, abuse, accident, ultraviolet
degradation and/or normal wear. The warranty does not cover
any trailers used for rental, competition, or commercial use.
Burley neither assumes nor authorizes any person to
assume any other liability in connection with Burley
trailers, and there are no oral agreements or warranties
collateral to or affecting this agreement.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Copyright © 2000-2002 by Burley Design Cooperative • www.burley.com
“Burley” is a registered trademark of Burley Design Cooperative
and “Burley-Cub” is a trademark of Burley Design Cooperative
Printed on recycled paper rev 8/02
Burley Design Cooperative • 4020 Stewart Rd. • Eugene, OR 97402 USA
(541) 687-1644 • Fax (541) 687-0436
Congratulations!
You’ve just purchased a Burley® trailer, the leading choice of
discriminating bicycle trailer owners worldwide. Every effort has
been made to ensure your purchase is of top quality and proven
design, ready to provide you with many years and miles of happy,
safe trailering.
IMPORTANT: Because some of the features and guidelines for using
the Burley-Cub merit close attention, it is very important that you
familiarize yourself with the trailer by reading this entire manual
before use. If you have any questions, we encourage you to contact
your authorized Burley dealer.
Introduction
Your Burley-Cub is shipped almost completely assembled from the
factory. This manual is written sequentially to assist initial setup. You
need only to install the quick-release levers, mount the reflectors,
attach the wheels, unfold the trailer, install the safety flag and snap on
the cover. Once you've read the safety guidelines, you're ready to go.
Before trailering, be sure you have a thorough understanding of the
safety harness and of trailer hitch operation. Practice folding and
unfolding your trailer; it can easily be done in less than a minute
after practice, no tools required. Check to see that the trailer wheels
and hitch are securely attached. We again request that you read this
manual from start to finish before use, and then refer to it as
necessary in the future.
NOTE: Any reference to left or right is made in the direction of travel, as if
you were sitting in the child seat looking forward.
When Loaning or Selling Your Trailer
If you loan or sell your Burley-Cub, supply the new user with this
manual. They must familiarize themselves with all sections—
especially sections “X. Safety Guidelines” and “XI. Safety Check-
lists” prior to use. It is essential that they understand the differences
between riding a bicycle with a trailer and without one. It is also
essential that they understand correct wheel attachment, folding,
and use of the harness, safety flag, cover, and hitch. Always ensure
that both adult and children are wearing helmets. Never loan your
trailer if it is need of maintenance or repair.
2
Your serial number is located on the bottom of the axle assembly. Please
have your serial number ready when requesting replacement parts.
23
I. Hardware Bag Contents & Tool List
IMPORTANT: Please verify that you have received all of the contents
listed. Do not proceed with assembly if any parts are missing;
contact Burley immediately for replacement parts.
HARDWARE BAG CONTENTS
Parts
(1) Tongue & hitch assembly
(2) Wheel
(1) Two-piece safety flag
Envelope
Trailer checklist (outside of envelope)
Warranty card
Burley-Cub Owner’s Instruction & Safety Manual
Remove the wheels, tongue and hitch, safety flag, and envelope from
the inside of your Burley-Cub. Try to do all initial assembly with the
trailer on a clean sturdy table or work bench to make handling the
trailer easiest and to keep the fabric clean. If you must work on a
rough or dirty surface instead, be sure to lay down a cloth or the
flattened shipping carton to avoid damage to the trailer.
II. Attaching the Wheels
First, verify that the tires are inflated to 30-35 P.S.I. Next, tip the
trailer frame on its back end. If you are working on a rough or dirty
surface, lay down a cloth or other protective barrier to avoid damage
to your trailer. With the quick-release lever in the "OPEN" position,
insert the wheel axle assembly completely into the hollow trailer
axle, making sure that the horizontal shaft goes all the way into
the axle.
3
Quick-release
lever in unlocked
"OPEN" position
Quick-release
lever in locked
"CLOSED"
position Wheel axle assembly inserts into
hollow trailer axle
XI. Parts List & Drawing
Note: Subassemblies are indented; inquire for additional parts
1. (1) Polyethylene Shell
2. (2) Front Reflector (Clear)
3. (2) Rear Reflector (Red)
4. (2) Suspension Elastomer
5. (1) Pair Side Panel Hold Down (Left & Right)
6. (1) Tongue Retaining Pin
7. (1) Pair Tongue Receptacle (Front & Rear)
8. (1) Safety Pin & Tether
9. (1) Front Roll Bar, 7/8" Aluminum Tube
10. (1) Roll-Bar Handle Assembly
11. (2) Front Roll-Bar Hinge (Plastic)
12. (1) Rear Roll Bar, 7/8" Aluminum Tube
13. (2) Rear Roll-Bar Hinge (Plastic)
14. (2) Roll-Bar Saddle (Plastic)
15. (1) Tongue & Hitch Assembly
16. (1) Tongue, 1 1/8" Square Aluminum
17. (1) Hitch with Hitch Knob & Ball
18. (1) Hitch Safety Strap
19. (1) Clip & D-Ring
20. (1) Rubber Flex Connector (Not Available Without Hitch)
21. (1) Pair Fabric Side-Panel Assembly, with Vinyl Windows
22. (1) Seat Pad
23. (1) Hold Down Strip, Seat Back & Pad
24. (1) Flow-Thru Seat Back with Harness
25. (4) Shoulder Strap
26. (3) Crotch Strap
27. (1) Lap Belt
28. (1) Buckle for Lap Belt
29. (2) Plastic Wheel, Each with (2) Wheel Bearing
30. (2) Wheel Reflector (Clear) with Self-Tapping Screw
31. (1) Swing Arm Assembly
32. (2) Hollow Axle
33. (2) Wheel Axle Assembly
34. (2) Quick-Release Lever
35. (1) Two-Piece Safety Flag
36. (1) Wide Screen 2-in-1 Cover
Options (at additional cost):
Walk ’n Roller Stroller Kit (not shown)
Alloy-Wheel Option
22


Produktspezifikationen

Marke: Burley
Kategorie: Diversen
Modell: Cub 1996-2003

Brauchst du Hilfe?

Wenn Sie Hilfe mit Burley Cub 1996-2003 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Diversen Burley

Bedienungsanleitung Diversen

Neueste Bedienungsanleitung fĂĽr -Kategorien-