Brother ScanNCut SDX135 Bedienungsanleitung
Brother
Papierschneider
ScanNCut SDX135
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Brother ScanNCut SDX135 (12 Seiten) in der Kategorie Papierschneider. Dieser Bedienungsanleitung war fĂĽr 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
1
Basic Quilting Guide
– Making a Quilt –
cFabric ............................................... We recommend 100% cotton that is not too thick.
cQuilt batting ..................................... Normally, medium-thick 100% polyester batting is used.
There is also cotton batting.
cThread .............................................. Since there are various types, for example, for piecing, for
quilting, for hand-sewing and for machine-sewing, select
the type appropriate for the desired purpose and use.
cSewing needles/pins.......................... Since there are various types, for example, for piecing
and for quilting, select the type appropriate for the
desired purpose.
cQuilting pencil (erasable pen, etc.) ... Use to copy patterns onto fabric and to draw quilting
lines.
cThimble ............................................ Use to protect your fingers when
quilting.
Place a thimble on the middle
finger of your right hand to push
the needle and on the middle or
index finger of your left hand to
stop the needle.
cQuilting hoop ................................... Use the hoop for quilting with a
cleaner finish.
cThread clipper
cIron/press
cMeasuring stick
1 Preparing Materials and Equipment
2
Refer to “Cutting Around Drawings” in the Operation Manual to specify a seam
allowance and draw the pattern lines, and then cut out the pieces. Be sure to
observe the following instructions.
1Check the fabric grain (weaving direction).
* When making pieces from patterned fabric,
the pattern has priority over the fabric grain.
* Observe the fabric grain on the pattern if it is
indicated.
2If a seam allowance will be drawn, attach the
fabric with the wrong side facing up.
Align the lengthwise grain with the insertion
direction.
3Select the patterns, and then arrange them.
If the fabric grain and pattern angle are not
aligned, rotate the pattern.
* Pre-installed patterns will automatically be
arranged with their grain along the
lengthwise grain of the fabric.
4Specify the seam allowance.
Widths that can be specified with this
machine: 3 mm, 5mm, 1/4", 7mm, 10mm,
1/2", 5/8"
1Stitching line
2Seam allowance
2 Cutting Pieces (Fabric)
Lengthwise-grain
fabric Hard to stretch
Crosswise-grain
fabric Slightly stretched
Bias-grain fabric Easy to stretch
1Lengthwise-
grain fabric
2Crosswise-
grain fabric
3Bias-grain
fabric
4Selvage
1Standard mat
2High tack adhesive
fabric support sheet
(An additional
purchase may be
required depending
on the machine
model.)
3Wrong side of
fabric
Standard seam allowance
Patchwork 5 mm (3/16"), 1/4", 7 mm
Appliqué 3 mm (1/8"), 5 mm (3/16")
3
Memo
â—ŹIf you are using a sewing machine to make
the quilt, refer to your machine’s instruction
manual for information about the straight
stitch, reverse/reinforcement stitch and
appliqué stitch. When sewing pieces
together without sewing reverse/
reinforcement stitches, sew fine stitches,
which have a short stitch length.
Make a knot at the end of the thread to secure it.
1Wind the thread 2 or 3 times around the
needle.
2Hold the wound thread and pull out the
needle.
1Thread knot
3Use scissors to cut off any excess thread.
Sew fine stitches when sewing pieces together.
12 mm (1/16 inch)
Attach appliqués so that threads are imperceptible.
1Insert the needle
2Feed out the needle
At the beginning and end of stitching, sew one
backstitch, and then secure the thread to prevent it
from becoming loose.
1Feed out the needle
2Insert the needle
3Feed out the needle
4Backstitch
At the end of stitching, sew a backstitch, make a
knot, and then cut the thread.
1Place the needle at the end of stitching.
1Backstitch
2Wind the thread twice around the needle,
hold the wound thread with your finger, and
then pull out the needle.
3 Basic Hand Sewing Techniques
Thread knot
Running stitch
Blindstitch
Backstitch
French knot
Produktspezifikationen
| Marke: | Brother |
| Kategorie: | Papierschneider |
| Modell: | ScanNCut SDX135 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Brother ScanNCut SDX135 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Papierschneider Brother
25 August 2024
25 August 2024
25 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
24 August 2024
Bedienungsanleitung Papierschneider
- Papierschneider HP
- Papierschneider Roland
- Papierschneider Camry
- Papierschneider Lervia
- Papierschneider Renkforce
- Papierschneider Ideen Welt
- Papierschneider Olympia
- Papierschneider United Office
- Papierschneider Rexel
- Papierschneider Fellowes
- Papierschneider Desq
- Papierschneider Acco
- Papierschneider Genie
- Papierschneider Dahle
- Papierschneider IDEAL
- Papierschneider Swordfish
Neueste Bedienungsanleitung fĂĽr -Kategorien-
6 Oktober 2024
17 September 2024
2 September 2024
2 September 2024
2 September 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024