Broan NuTone Bedienungsanleitung
Broan
Sicherheitskamera
NuTone
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr Broan NuTone (7 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war fĂŒr 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/7
MODEL LA542WH
Page 1
WIRELESS DOOR CHIME
Installation & Operating Instructions
IMPORTANT: This wireless pushbutton and chime set is for
residential use, only. It will operate at an unobstructed distance
of 300 feet. Building materials may reduce operating distance.
Certain building materials; such as, but not limited to metal,
concrete, brick, stucco and foil-lined insulation; cause greater
interference than others; for example, wood or vinyl siding.
INSTALL PUSHBUTTON BATTERY
Refer to Figures 1 and 2.
1. Remove pushbutton and 3V lithium coin-battery from packaging.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its base.
3. Orient battery with â+â side viewable.
4. Insert battery into holder and press to seat.
5. Insert top of mounting base onto pushbutton and press bottom
together until mounting base snaps securely onto pushbutton.
Use only 3V (volt) lithium CR2032 style coin-battery for replacement.
INSTALL CHIME BATTERIES
Refer to Figures 3 and 4.
1. Remove chime from packaging.
2. Use finger to depress tab and remove chime cover. Set cover aside.
3. Insert three (3) 1.5V âDâ alkaline batteries (not supplied) oriented as
shown on front of battery compartment.
4. Replace chime cover.
Figure 1
âPUSHâ
TO OPEN COVER
3V LITHIUM
CR2032-STYLE
COIN
BATTERY
Figure 2
SLOT
âLEARNâ PROCEDURE
Refer to Figure 5.
1. Set pushbutton and chime next to each other.
2. Press and release âLearnâ button on chime.
3. LED lights to indicate âLearnâ mode was entered.
4. Press and release pushbutton.
5. Confirm chime-tone is heard.
6. Repeat Step 4 to cycle through available chime-tones.
7. When desired chime-tone is heard, press and release âLearnâ button
(Note: Chime may not respond to this button being pressed if it is too
soon after chime-tone sounds).
8. LED should turn off to confirm âLearnâ mode exited.
9. Press and release pushbutton and confirm chime-tone hasnât change
from desired one.
âą Up to four (4) pushbuttons can be used with a single chime by
selecting different chime-tones for each pushbutton.
âą Chime can erase all âLearnedâ pushbuttons and tones by pressing
and holding âLearnâ button; LED will light; within 20 seconds, LED will
turn off; release âLearnâ button.
DETERMINE USABLE LOCATIONS
Do not plan to mount pushbutton directly on metal or concrete
surfaces; install a 1/8-1/4â wood spacer between pushbutton and
metal or concrete mounting surface.
Some stucco houses have metal mesh in the wall structure, which
will affect the wireless chime performance.
Experiment with various pushbutton and chime locations to
determine location that gives best performance before mounting
permanently.
Chime must not be located within 1-foot of any metal.
Pushbutton and chime should be located within 300-feet of each
other.
1. Place chime near desired mounting location.
2. Select a level location and hold pushbutton in desired mounting
location.
3. Press and release pushbutton.
4. Confirm chime-tone sounded.
5. If chime-tone does not sound, temporarily affix pushbutton to
mounting surface with double-stick or folded-over tape; repeat Steps 3
and 4.
6. If chime-tone still does not sound, move location of chime closer to
pushbutton; repeat Steps 3 and 4.
Figure 3 Figure 4
Figure 5
VOLUME BUTTON
LEARN BUTTON LED
MODEL LA542WH
Page 2
Figure 6
MOUNT PUSHBUTTON
Refer to Figures 1 and 6.
1. After selecting usable locations in previous section, go to pushbutton
location.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its mounting base.
3. Make sure pushbutton mounting location is level.
4. Position pushbutton mounting base with âTOPâ arrow correctly
oriented and mark base mounting holes locations.
5. Drill two (2) holes, 1/16â diameter if using supplied screws alone or
3/16â diameter if using supplied plastic anchors and screws, at base
mounting hole locations.
6. If 3/16â diameter holes were drilled, insert supplied plastic anchors.
7. Secure pushbutton base to mounting location with two (2) supplied
screws.
8. Make sure black O-ring is completely seated in its mounting base
groove with round edge at top and flat edge at bottom.
9. Hook pushbutton top catch onto top of base, swing pushbutton into
position and press bottom of pushbutton until it securely snaps onto
base.
SET VOLUME PROCEDURE
Refer to Figure 5.
There are four (4) volume levels which are accessed sequentially.
1. Press and release pushbutton to sound chime tone.
2. Press and release âVolumeâ button to hear the next volume setting.
3. If chime tone is not sounding when âVolumeâ button is pressed then
chime will sound a beep to indicate volume setting.
4. Volume setting cycles from loud to medium-loud, medium-soft and soft
then back to loud.
5. Repeat Step 2 until desired volume level is set.
6. Last volume setting is remembered.
7. Press and release pushbutton to sound chime tone and confirm
desired volume setting.
BASE
PLASTIC
ANCHORS
TOP
î±
BLACK
âOâ RING
MOUNTING
SCREWS
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Regulatory Information
The user is cautioned that changes or modifications not expressly
approved by the party responsible for regulatory compliance
could void the userâs authority to operate this equipment.
MOUNT CHIME
Refer to Figure 7.
1. Go to selected chime location.
2. There are two ways to mount this chime
a. Back-plate permanently mounted to wall; or
b. Back-plate removable from wall.
Select desire back-plate mounting method.
3. Measure down from top of desired chime location and mark
mounting screw(s) position(s).
a. 1-1/8â and centered, and 3-3/8â down from first mark and 1-5/16â
either side of center; or
b. 7/8â and 1-5/16â either side of center.
4. Drill holes, 1/16â diameter if using supplied screws alone or 3/16â
diameter if using supplied plastic anchors and screws, at marked
mounting screw locations.
5. If 3/16â diameter holes were drilled, insert supplied plastic anchors.
6a. Place screw through back-plate centered hole and into mounting
hole and tighten until 1/8â remains protruding.
Place (2) screws through back-plate bottom holes and into mounting
holes and tighten until snug.
Tighten top screw until it is snug.
6b. Place screws into mounting holes and tighten until 1/8â remains
protruding.
Place back-plate keyhole slots over mounting screws and apply slight
downward force to seat keyhole slot on mounting screw.
7. Hook chime top to back-plate, swing chime bottom towards back-
plate and press on front-bottom of chime until chime is secured to
back-plate.
TROUBLESHOOTING GUIDE
1. Chime does not sound:
a. If pushbutton LED doesnât light when pushbutton is pressed then:
1. Check battery polarity in pushbutton.
2. Replace battery in pushbutton.
b. Replace batteries in chime.
c. Bring pushbutton in area of chime and test:
1. If chime sounds then change location of chime.
2. If chime does not sound then conduct erase procedure per note
at end of âLearnâ Procedure then conduct âLearnâ Procedure,
Steps 1 through 9.
2. Chime loses volume or changes tone: Change batteries in chime.
3. Chime sounds when pushbutton is not pressed:
a. Release pushbutton catch at bottom and check inside for signs of
moisture; check O-ring for cracks or damage.
b. Conduct erase procedure per note at end of âLearnâ Procedure then
conduct âLearnâ Procedure, Steps 1 through 9.
Figure 7
1/8â
7/8â
MOUNTING
METHOD SHOWN:
Back-plate
removable from wall.
See 2. b. below.
MODĂLE LA542WH
Page 3
CARILLON DE PORTE SANS FIL
Directives dâinstallation et dâutilisation
IMPORTANT : Cet ensemble de bouton-poussoir et de carillon sans fil est conçu
uniquement pour un usage rĂ©sidentiel. Il fonctionne jusquâĂ une distance sans
obstruction dâau moins 91 mĂštres (300 pi). Des matĂ©riaux de construction peuvent
en réduire la portée. Certains matériaux de construction comme le métal, le
bĂ©ton, la brique, le stucco et lâisolant couvert de papier aluminium causent plus
dâinterfĂ©rences que dâautres comme le parement de bois ou de vinyle.
INSTALLATION DE LA PILE DU BOUTON-POUSSOIR
Voir les figures 1 et 2.
1. Sortez de lâemballage le bouton-poussoir et la pile bouton de 3V auîlithium.
2. Insérez un petit tournevis plat au bas du bouton-poussoir et tournez-le pour en
séparer la base.
3. Placez la pile avec le cÎté « + » visible.
4. InsĂ©rez la pile dans son logement et pressez pour lâappuyer.
5. Insérez la base dans le bouton-poussoir et pressez les deux parties ensemble
pour bien les emboĂźter.
Nâutilisez quâune pile bouton de 3V (volts) au lithium CR2032 comme pile
deîremplacement.
INSTALLATION DES PILES DU CARILLON
Voir les figures 3 et 4.
1. Sortez le carillon de lâemballage.
2. Avec le doigt, appuyez sur lâergot et retirez le couvercle du carillon. Mettez le
couvercle de cÎté.
3. Insérez trois (3) piles alcalines « D » de 1,5 V (non comprises) dans le sens
indiquĂ© Ă lâavant du compartiment Ă piles.
4. Replacez le couvercle.
Figure 1
« POUSSER »
POUR OUVRIR LE
COUVERCLE
PILE BOUTON
AU LITHIUM
CR2032 3V
Figure 2
FENTE
PROCĂDURE Dâ« APPRENTISSAGE »
Voir la figure 5.
1. Placez le bouton-poussoir et le carillon lâun Ă cĂŽtĂ© de lâautre.
2. Appuyez sur le bouton « Apprendre » sur le carillon puis relùchez-le.
3. La DEL sâallume pour indiquer que vous ĂȘtes entrĂ© en mode « Apprentissage ».
4. Appuyez sur le bouton-poussoir et relĂąchez-le.
5. Confirmez que vous avez bien entendu le carillon.
6. RĂ©pĂ©tez lâĂ©tape 4 pour passer entre les tonalitĂ©s du carillon.
7. Lorsque vous entendez le type de carillon souhaité, appuyez sur le bouton
« Apprendre ». (Remarque : le carillon risque de ne pas réagir si vous appuyez
trop tÎt sur ce bouton aprÚs que le carillon ait résonné).
8. La DEL devrait sâĂ©teindre pour confirmer que vous avez quittĂ© le mode
« Apprentissage ».
9. Appuyez sur le bouton-poussoir et relùchez-le pour vérifier que la tonalité du
carillon nâa pas changĂ©.
âą Vous pouvez utiliser jusquâĂ quatre (4) boutons-poussoirs avec le mĂȘme carillon
en choisissant des tonalités différentes pour chacun.
⹠Le carillon peut effacer tous les boutons-poussoirs et tonalités « appris » si vous
maintenez appuyĂ© le bouton « Apprendre »; la DEL sâallume alors; aprĂšs environ
20 secondes la DEL sâĂ©teint; relĂąchez alors le bouton « Apprendre ».
CHOIX DES EMPLACEMENTS UTILISABLES
Ne fixez pas le bouton-poussoir directement sur une surface en métal ou en
béton; installez une petite cale en bois de 3,2 à 6,4 mm (1/8 à 1/4 po) entre le
bouton et la surface métallique ou en béton.
Certaines maisons Ă revĂȘtement en stucco ont un treillis mĂ©tallique dans
leur charpente, ce qui nuira au fonctionnement du carillon.
Essayez divers emplacements pour le bouton-poussoir et le carillon pour
déterminer le meilleur endroit possible avant de les fixer en permanence.
Le carillon ne doit pas ĂȘtre situĂ© Ă moins de 30,5 cm (1 pi) de toute surface
métallique.
Le bouton-poussoir et le carillon ne doivent pas ĂȘtre sĂ©parĂ©s de plus de
91îmĂštres (300 pi) lâun de lâautre.
1. Placez le carillon prĂšs de lâendroit oĂč il sera fixĂ©.
2. Choisissez un endroit de niveau et tenez le bouton-poussoir Ă
lâemplacementîvoulu.
3. Appuyez sur le bouton-poussoir et relĂąchez-le.
4. Vérifiez que le carillon a bien sonné.
5. Si le carillon ne sonne pas, fixez temporairement le bouton-poussoir Ă la surface de
montage avec du ruban double face ou un ruban replié; répétez les étapes 3 et 4.
6. Si le carillon ne sonne toujours pas, rapprochez le carillon du bouton-poussoir;
répétez les étapes 3 et 4.
Figure 3 Figure 4
Figure 5
BOUTON DE
VOLUME
BOUTON
APPRENDRE DEL
Produktspezifikationen
Marke: | Broan |
Kategorie: | Sicherheitskamera |
Modell: | NuTone |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Broan NuTone benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sicherheitskamera Broan
28 MĂ€rz 2024
Bedienungsanleitung Sicherheitskamera
- Sicherheitskamera Samsung
- Sicherheitskamera Sanyo
- Sicherheitskamera Exibel
- Sicherheitskamera Gembird
- Sicherheitskamera Manhattan
- Sicherheitskamera Nedis
- Sicherheitskamera Sony
- Sicherheitskamera Panasonic
- Sicherheitskamera Profile
- Sicherheitskamera LG
- Sicherheitskamera Bosch
- Sicherheitskamera Canon
- Sicherheitskamera TechniSat
- Sicherheitskamera Eminent
- Sicherheitskamera Linksys
- Sicherheitskamera Maginon
- Sicherheitskamera Netgear
- Sicherheitskamera Schwaiger
- Sicherheitskamera Technaxx
- Sicherheitskamera Alecto
- Sicherheitskamera Denver
- Sicherheitskamera EMOS
- Sicherheitskamera König
- Sicherheitskamera Thomson
- Sicherheitskamera Blaupunkt
- Sicherheitskamera Braun
- Sicherheitskamera Pyle
- Sicherheitskamera Mitsubishi
- Sicherheitskamera Jay-Tech
- Sicherheitskamera JVC
- Sicherheitskamera Abus
- Sicherheitskamera Avidsen
- Sicherheitskamera Elro
- Sicherheitskamera EZVIZ
- Sicherheitskamera Imou
- Sicherheitskamera INSTAR
- Sicherheitskamera Olympia
- Sicherheitskamera Smartwares
- Sicherheitskamera Strong
- Sicherheitskamera Toshiba
- Sicherheitskamera Lindy
- Sicherheitskamera Burg WĂ€chter
- Sicherheitskamera Marmitek
- Sicherheitskamera Marshall
- Sicherheitskamera Honeywell
- Sicherheitskamera B/R/K
- Sicherheitskamera TRENDnet
- Sicherheitskamera MINOX
- Sicherheitskamera Ricoh
- Sicherheitskamera RADEMACHER
- Sicherheitskamera First Alert
- Sicherheitskamera AVerMedia
- Sicherheitskamera Zebra
- Sicherheitskamera TP-Link
- Sicherheitskamera Humax
- Sicherheitskamera Kerbl
- Sicherheitskamera InFocus
- Sicherheitskamera Overmax
- Sicherheitskamera Monacor
- Sicherheitskamera JUNG
- Sicherheitskamera Ednet
- Sicherheitskamera AG Neovo
- Sicherheitskamera Nest
- Sicherheitskamera Edimax
- Sicherheitskamera Uniden
- Sicherheitskamera M-e
- Sicherheitskamera Siedle
- Sicherheitskamera Conceptronic
- Sicherheitskamera D-Link
- Sicherheitskamera Eufy
- Sicherheitskamera Stabo
- Sicherheitskamera Friedland
- Sicherheitskamera Ring
- Sicherheitskamera Digitus
- Sicherheitskamera Swann
- Sicherheitskamera DataVideo
- Sicherheitskamera LevelOne
- Sicherheitskamera APC
- Sicherheitskamera Cisco
- Sicherheitskamera Grandstream
- Sicherheitskamera EVE
- Sicherheitskamera EasyMaxx
- Sicherheitskamera Tenda
- Sicherheitskamera Foscam
- Sicherheitskamera Ubiquiti Networks
- Sicherheitskamera Intellinet
- Sicherheitskamera Reolink
- Sicherheitskamera Hikvision
- Sicherheitskamera FLIR
- Sicherheitskamera Arlo
- Sicherheitskamera Nexxt
- Sicherheitskamera EnGenius
- Sicherheitskamera Lorex
- Sicherheitskamera Google
- Sicherheitskamera Comtrend
- Sicherheitskamera Dedicated Micros
- Sicherheitskamera EverFocus
- Sicherheitskamera Ganz
- Sicherheitskamera GeoVision
- Sicherheitskamera Raymarine
- Sicherheitskamera Revo
- Sicherheitskamera SecurityMan
- Sicherheitskamera Sitecom
- Sicherheitskamera Steren
- Sicherheitskamera Vivotek
- Sicherheitskamera Wanscam
- Sicherheitskamera Y-cam
- Sicherheitskamera ACTi
- Sicherheitskamera ZKTeco
- Sicherheitskamera AirLive
- Sicherheitskamera Mobotix
- Sicherheitskamera Hollyland
- Sicherheitskamera Dahua Technology
- Sicherheitskamera Speco Technologies
- Sicherheitskamera Aluratek
- Sicherheitskamera 3xLOGIC
- Sicherheitskamera Hanwha
- Sicherheitskamera Lupus Electronics
- Sicherheitskamera Joblotron
- Sicherheitskamera Axis
- Sicherheitskamera EtiamPro
- Sicherheitskamera Wisenet
- Sicherheitskamera Chacon
- Sicherheitskamera KT&C
- Sicherheitskamera EKO
- Sicherheitskamera KJB Security Products
- Sicherheitskamera BZBGear
- Sicherheitskamera Ansel
- Sicherheitskamera Aigis
- Sicherheitskamera Pelco
- Sicherheitskamera ORNO
- Sicherheitskamera Atlona
- Sicherheitskamera Aqara
- Sicherheitskamera Tecno
- Sicherheitskamera Lutec
- Sicherheitskamera Brinno
- Sicherheitskamera Exacq
- Sicherheitskamera UniView
- Sicherheitskamera Alfatron
- Sicherheitskamera Milestone Systems
- Sicherheitskamera Inkovideo
- Sicherheitskamera VideoComm
- Sicherheitskamera Kwikset
- Sicherheitskamera HiLook
- Sicherheitskamera Digital Watchdog
- Sicherheitskamera Channel Vision
- Sicherheitskamera Ikegami
- Sicherheitskamera Gewiss
- Sicherheitskamera Arenti
- Sicherheitskamera Costar
- Sicherheitskamera Sentry360
- Sicherheitskamera Seco-Larm
- Sicherheitskamera Spyclops
- Sicherheitskamera Hawking Technologies
- Sicherheitskamera IDIS
- Sicherheitskamera I3International
- Sicherheitskamera B & S Technology
Neueste Bedienungsanleitung fĂŒr -Kategorien-
11 August 2024
18 April 2024
18 April 2024
18 April 2024
17 April 2024
17 April 2024
16 April 2024
16 April 2024
16 April 2024
16 April 2024