Broan 9815WH Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Broan 9815WH (12 Seiten) in der Kategorie heater. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
1
INSTALLATION INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Wall Heaters
9810WH, 9815WH SERIES
READ ALL INSTRUCTIONS BEFORE INSTALLING OR
USING THIS HEATER.
To reduce the risk of fire, electric shock, or injury to persons,
observe the following:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer at the address or telephone number listed
in the warranty.
2. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by
a qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction
codes and standards.
4. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
5. This heater is hot when in use. To avoid burns, do not
let bare skin touch hot surfaces. Keep combustible
materials, such as furniture, pillows, bedding, papers,
clothes, etc. and curtains at least 3 feet (0.9 m) from the
front of the heater.
6. Extreme caution is necessary when any heater is used
by or near children or invalids and whenever the heater
is left operating and unattended.
7. Do not operate any heater after it malfunctions.
Disconnect power at service panel and have heater
inspected by a reputable electrician before reusing.
8. Do not use outdoors.
9. To disconnect heater, turn controls to off, and turn off
power to heater circuit at main disconnect panel (or
operate internal disconnect switch, if provided).
10. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening, as this may cause an
electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or
exhaust in any manner.
12. A heater has hot and arcing or sparking parts inside. Do
not use it in areas where gasoline, paint, or flammable
vapors or liquids are used or stored.
13. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons.
14. Install heater at least 6 inches from floor or any adjacent
wall.
15. To avoid electrical shock: Do not install unit in a tub or
shower enclosure or any location where it may come in
contact with water. Never place a switch where it can be
reached from a tub or shower.
16. This product may ONLY be installed vertically in a wall.
Do not mount in any other position.
17. Do not connect heater to dimmer switch or speed control.
18. This product must be grounded.
SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
SAFETY INSTRUCTIONS
• Carefully read all instructions and product labels before
beginning installation.
• Only mount the heater in a vertical position.
• Mount the heater at least 6” above the finished floor.
• Do not mount the heater over a bathtub or in a shower stall
enclosure.
• When mounted, the heater should not be closer than
12” to an adjacent wall.
• Do not block the wall heater — i.e., by mounting under a
towel rack, behind a door, etc.
ELECTRICAL SPECIFICATIONS
NOTE: See wiring label on heater housing. The heater
may be wired for either 120V or 240V operation and
requires a separate circuit.
UNIT DIMENSIONS
Housing: 121/2” high x 101/ 32” wide x 3/8” deep.
Grille: 143
/ 114” high x ” wide x 1” deep.
Wall Cutout: 125/ 08” high x 1 5/8” wide.
2
FIGURE 2
MOUNTING THE HOUSING
(New Construction)
Refer to Figure 1.
1. Choose heater location. Make sure the heater will not be
mounted closer than 12” from a vertical surface or 6”
from
the floor.
2. Using nails or screws, mount one side of housing to wall
stud. The flange must be flush to the stud.
3. Run wiring from circuit breaker or fuse box to heater
location.
4. Install box connector into wiring entrance hole in housing’s
junction box.
5. Pull wiring through entrance hole and secure cable to box
connector. Allow 6” of wiring to make connections.
6. Finished wall opening should be 125/8” high x 105/8” wide.
JUNCTION BOX
ROUGH-IN FRAME
WALL
CUTOUT
WALL STUDS
←
10
5
/
8
”
→
← 125/ ” 8→
FIGURE 1
EXISTING
CONSTRUCTION
NEW CONSTRUCTION
MOUNTING THE HOUSING
(Existing Construction)
1. Choose heater location. Make sure the heater will not be
mounted closer than 12” from a vertical surface or 6”
from the floor.
2. Refer to Figure 2. Make wall cutout next to a wall stud.
Cutout size: 125/8” high x 105/8” wide.with frame.)
3. Run wiring from circuit breaker or fuse box to heater
location.
4. Install box connector into wiring entrance hole in housing’s
junction box.
5. Pull wiring through cutout and secure cable to box
connector. Allow 6” of wiring to make connections.
6. Refer to Figure 3. Insert TOP of housing into cutout first
so that box connector clears the wall. Then, insert bottom
of housing into cutout. The flange must be flush with the
wall.
7. Use nails or screws to mount one side of housing to wall
stud.
FIGURE 3
WALL STUDS
JUNCTION BOX
HEATER ASSMBLY
FLANGE
MOUNTING
HOLES
ROUGH-IN
BOX
“B” UNIT MOUNTING HOLE
- TOP AND BOTTOM
INSTALLATION
WARNING: To reduce the risk of fire, do not store or use
gasoline or other flammable vapors and liquids in the
vicinity of the heater.
CAUTION: High temperature, risk of fire, keep electrical
cords, drapery, furnishings, and other combustibles at
least 3 feet (0.9 m) from the front of the heater and away
from the side and rear.
3
WIRING CONNECTIONS
Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
1. While making wiring connections, support the heater
assembly on the bottom of the rough-in frame.
2. For 120 Volt operation, make wiring connections as shown
in Figure 4.
3. For 240 Volt operation, make wiring connections as shown
in Figure 5.
4. Use wire nuts to make connections. Insulate all
connections with electrical tape.
SECURING THE HEATER
1. Dress all wiring back to into junction box.
2. Locate center holes in housing flange and align with
mounting holes in grille.
3. Use two provided screws to attach grille to housing.
4
1
2
3
4
1
2
3
FIGURE 4
FIGURE 5
120vAC
240vAC
GREEN OR BARE
GROUND
GREEN
GROUND
WHITE
BLACK
BLACK
RED
WHITE
YELLOW
120vAC
60HZ
GREEN OR BARE
GROUND
GREEN
GROUND
RED OR WHITE
BLACKBLACK
RED
WHITE
YELLOW
240vAC
60HZ
NO
CONNECTION
NO
CONNECTION
Produktspezifikationen
Marke: | Broan |
Kategorie: | heater |
Modell: | 9815WH |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Broan 9815WH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung heater Broan
5 September 2024
Bedienungsanleitung heater
- heater Sinbo
- heater AFK
- heater Infiniton
- heater Clatronic
- heater Domo
- heater Emerio
- heater Tristar
- heater HP
- heater Nedis
- heater Philips
- heater SilverCrest
- heater Sunbeam
- heater Cotech
- heater Profile
- heater Quigg
- heater Adler
- heater Camry
- heater Guzzanti
- heater Princess
- heater Bosch
- heater Parkside
- heater Vonroc
- heater AEG
- heater Ardes
- heater Bauknecht
- heater Concept
- heater Electrolux
- heater Fagor
- heater Gorenje
- heater Jata
- heater Klarstein
- heater Lervia
- heater Solis
- heater Unold
- heater Bomann
- heater Essentiel B
- heater Hendi
- heater Korona
- heater Melissa
- heater OK
- heater Steba
- heater Taurus
- heater Tefal
- heater Vox
- heater Velleman
- heater ECG
- heater EMOS
- heater Thomson
- heater Black And Decker
- heater Trotec
- heater Blaupunkt
- heater Cuisinart
- heater Eldom
- heater Eta
- heater Heinner
- heater Hema
- heater Maestro
- heater Prime3
- heater Primo
- heater Solac
- heater Wilfa
- heater Dometic
- heater Eureka
- heater Alpina
- heater Candy
- heater DeWalt
- heater Corberó
- heater Einhell
- heater Bartscher
- heater Lynx
- heater Midea
- heater Otsein-Hoover
- heater Svan
- heater Zanussi
- heater King
- heater Eurom
- heater Elro
- heater Olympia
- heater Hyundai
- heater Orava
- heater Livoo
- heater Stanley
- heater DCG
- heater Tectro
- heater Crane
- heater Güde
- heater Perel
- heater Bimar
- heater Stadler Form
- heater Rowenta
- heater Sencor
- heater DeLonghi
- heater Piazzetta
- heater Vasco
- heater Hartig And Helling
- heater Reer
- heater Maxwell
- heater Ariete
- heater Kalorik
- heater Optimum
- heater Scarlett
- heater Superior
- heater Ufesa
- heater Anslut
- heater Calor
- heater Cecotec
- heater Qlima
- heater Bionaire
- heater Duux
- heater Haverland
- heater Honeywell
- heater Remko
- heater Suntec
- heater Zibro
- heater Dedra
- heater Carson
- heater Zehnder
- heater MPM
- heater Thermex
- heater Imetec
- heater Logik
- heater Team
- heater Fluval
- heater Burley
- heater Stiebel Eltron
- heater Truma
- heater Brandson
- heater Heller
- heater Dimplex
- heater Sonnenkönig
- heater Eurolite
- heater Noirot
- heater Gre
- heater Mora
- heater Milwaukee
- heater Heylo
- heater Baxi
- heater Tesy
- heater Vivax
- heater EWT
- heater Kogan
- heater Royal Sovereign
- heater Innoliving
- heater Conceptronic
- heater Argo
- heater HQ
- heater Vasner
- heater Master
- heater Dovre
- heater Alpatec
- heater Olimpia Splendid
- heater SereneLife
- heater Sygonix
- heater Vitek
- heater AKO
- heater SHX
- heater Danby
- heater Sogo
- heater Fantini Cosmi
- heater Kent
- heater Mellerware
- heater Evolar
- heater EasyMaxx
- heater La Nordica
- heater Eden
- heater Real Flame
- heater Ferroli
- heater Zibro Kamin
- heater Blumfeldt
- heater Signature
- heater Wamsler
- heater Trumatic
- heater Sun Joe
- heater Noveen
- heater Swan
- heater Soler & Palau
- heater Mill
- heater Harvia
- heater Orbegozo
- heater Dantherm
- heater Izzy
- heater Jøtul
- heater Haas+Sohn
- heater Defy
- heater Duro Pro
- heater Duronic
- heater Etherma
- heater Extraflame
- heater Grandhall
- heater Heatstrip
- heater Jaga
- heater Jocel
- heater Just Fire
- heater Kambrook
- heater Kenmore
- heater Lavorwash
- heater Nestor Martin
- heater Nobo
- heater Nordic Fire
- heater Plieger
- heater Prem-i-air
- heater Solamagic
- heater SPT
- heater SunRed
- heater Vornado
- heater Waldbeck
- heater Wanders
- heater WestBend
- heater AstralPool
- heater Argoclima
- heater Lasko
- heater Hatco
- heater Barbecook
- heater Dri Eaz
- heater Kunft
- heater Becken
- heater Nevir
- heater Rinnai
- heater Blaze
- heater Masport
- heater Hubbell
- heater Escea
- heater Ravanson
- heater Pacific Energy
- heater XPower
- heater Lenoxx
- heater Neo
- heater Jindara
- heater NewAir
- heater Air King
- heater AENO
- heater Brivis
- heater Chauvet
- heater Creda
- heater Nectre
- heater IXL
- heater JANDY
- heater Martec
- heater Ionmax
- heater Regency
- heater Braemar
- heater GoldAir
- heater Arnold Rak
- heater Guardian
- heater Ouellet
- heater Gasmate
- heater Bromic
- heater Rheem
- heater Yellow Garden Line
- heater Scandia
- heater Pureheat
- heater Fiap
- heater Gossmann
- heater Quadra-Fire
- heater Everdure
- heater Blue Rhino
- heater Mission Air
- heater Create
- heater VIESTA
- heater Big Ass Fans
- heater Brentwood
- heater Omega Altise
- heater Airo
- heater Hortus
- heater Ausclimate
- heater Brixton
- heater Euromac
- heater TAIDEN
- heater Veito
- heater Tecno Air System
- heater Adax
- heater True North
- heater Heatsome
- heater Invroheat
- heater Herschel
- heater EvoHeat
- heater Fire Sense
- heater InfraNomic
- heater Heat Storm
- heater Excelair
- heater Heatscope
- heater LifeSmart
- heater Heat1
- heater Kemlan
- heater Perfect Aire
- heater AustWood
Neueste Bedienungsanleitung für -Kategorien-
18 September 2024
18 September 2024
18 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024
17 September 2024