Britax Advansafix Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr Britax Advansafix (2 Seiten) in der Kategorie Autositz. Dieser Bedienungsanleitung war fĂŒr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
A correctly adjusted headrest 07 ensures optimal protection
for your child in the safety seat:
The headrest 07 must be adjusted so that the shoulder belts
08 are at the same level as your childâs shoulders.
CAUTION! The shoulder belts 08 must not run behind the
back of the child or at ear height or above the ears.
The shoulder belts are adjusted as follows:
1. Loosen the 5-point harness 38 of the child seat as much
as possible.
Back side of the child seat:
2. Press the button of the shoulder belt height adjuster 10 at
the rear of the seat shell and tilt the shoulder belt height
adjuster 10 towards you.
3. Slide the shoulder belt height adjuster 10 to select the
correct height of the shoulder belts 08 and engage it in the
positon that ïŹts for your child by releasing the button.
A correctly adjusted headrest 07 ensures that the diagonal
seat belt section 11 is optimally positioned, and gives your
child the optimal protection.
The headrest 07 must be adjusted so that there is a space
two ïŹngers wide between the headrest 07 and your childâs
shoulders.
To adjust the height of the headrest to ïŹt your child:
1. Squeeze the adjustment handle 12 on the back of the
headrest 07 .
This unlocks the headrest.
2. You can now move the unlocked headrest 07 to the desired
height. As soon as you release the adjustment handle 12
the headrest 07 will lock into place.
3. Place the child seat on the vehicle seat.
4. Have your child sit down in the child seat and check the
height. Repeat this process until the headrest 07 is at
the optimal height. If in the lowest position the headrest
07 is still too high, additional adjustment can be made
through the shoulder belt height adjuster 10 , as explanied
in section 5.2
5.3. Adjusting the headrest in Vehicle belt installation
1. If your vehicle is not equipped with the ISOFIX insert guides
as standard, clip the two insert guides 02 which are inclu-
ded with the seat* with the cut-out facing upwards onto
the two ISOFIX attachment points 01 of your vehicle.
TIP: The ISOFIX attachment points are located between the
surface and the backrest of the vehicle seat.
2. Move the head restraint on the vehicle seat to the upper
position.
3. Pull the grey fabric loop 03 to pull out both locking arms
15 until you hear a click sound which indicates they are
fully engaged.
4. On both sides of the seat squeeze the green safety button
04 and the red release button 05 together and remove
the connector protection 06 .
* The insert guides make it easier to install the child safety seat with the aid of the ISOFIX
attachment points and prevent damage to the seat covering. When not in use, they should
be removed and stored in a safe place. On vehicles with a folding backrest the insert guides
must be removed before the backrest is folded.
Any problems which occur are usually caused by dirt or foreign objects on the insert guides
and on the hooks. Clean oî any dirt or foreign objects to remedy this type of problem.
5. PREPARATORY WORK
5.1 Prepare ISOFIX
5.2 Adjusting the headrest in 5-point harness installation
02
01
Please read the chapter with your desired installation method in chapter 6 ïŹrst.
07
08
10
07
11
12
38
For the safety of your child, before every journey in the car check that...
âșthe child safety seat is engaged on sides with the ISOFIT locking arms both 15 in the
ISOFIX attachment points 01 and that both green safety buttons 04 are completely
green;
âșthe child seat is ïŹrmly installed in the vehicle;
âșthe belt is not twisted;
âșthe Top Tether 13 is tightly tensioned over the backrest of the car seat and the tension
indicator 18 is green;
âșthe diagonal belt is only clamped by the lock-oî which is located on the opposite side
from the car seat belt buckle;
âșthe straps of the child safety seat are close to the body without constricting the child;
âșthe shoulder belts 08 are correctly adjusted and the straps are not twisted;
âșthe shoulder pads 19 are at the same level as your childÂŽs shoulders;
âșthe buckle latches 20 are engaged in the harness buckle 21 ;
âșthe vehicle belt 22 clamped in the lock-oî 25 is tensioned correctly.
Caution: If your child attempts to open the green safety buttons 04 or the harness
buckle 21 , make sure to stop at the earliest opportunity. Check that the child safety
seat is correctly attached and make sure that your child is properly secured. Teach
your child about the dangers involved.
6. Grasp the child seat with both hands and slide the two
locking arms 15 ïŹrmly into the insert guides 02 until the
locking arms engage with a clicking noise on both sides.
The green safety button 04 must now be visible on both
sides.
The locking arms are only correctly engaged if CAUTION!
both of the safety buttons 04 are completely green.
1. Make sure that the child seats 5-point harness is removed
correctly (see section 9)
2. Follow the steps in section 5.1
3. Follow the steps in section 5.3
4. Take the Top Tether 13 from the storage bag 14 and lay it
over the child seat.
5. Place the child seat facing in the direction of travel on the
vehicle seat.
7. Push the child seat towards the backrest applying ïŹrm, even
pressure on both sides.
8. Shake the child safety seat to make sure it is safely attached
and re-check to the green safety buttons 04 to make sure
that both of them are completely green
13. Have your child sit down in the child seat.
14. Pull out the vehicle seat belt and guide it in front of your child
to the vehicle seat buckle 29 .
Do not twist the belt.CAUTION!
15. Engage the buckle tongue in the vehicle seat buckle 29
CLICK!
16. Place the diagonal seat belt section 11 and lap belt section
28 on the side of the vehicle seat belt buckle 29 under the
armrest and into the light red belt guide 23 of the child seat.
CAUTION! The vehicle seat belt buckle 29 must not be
positioned between the light red belt guide 23 and the armrest.
17. Place the lap belt section 28 on the other side of the child
seat in the light red belt guide 23 .
The lap belt section CAUTION! 28 must lie as low as pos-
sible over your childâs hips on both sides
18. Guide the diagonal seat belt section 11 into the dark red
belt holder 30 of the headrest 07 until it lies completely in
the belt holder 30 and is not twisted.
Tip! If the backrest 31 conceals the belt holder 30 , you can
adjust the headrest 07 upwards. The diagonal seat belt section
11 can now be easily inserted. Now return the headrest 07 to
the proper height, as in Section 5.3.
19. Make sure that the diagonal seat belt section 11 runs over
your childâs shoulder bone, and not in front of his or her
neck.
Tip! You can still adjust the height of the headrest 07 again here
in the vehicle.
The diagonal seat belt section CAUTION! 11 must run dia-
gonally backward. You can adjust the course of the belt with your
vehicleâs adjustable belt deïŹector.
The diagonal seat belt section CAUTION! 11 must never
lead forward to the vehicleâs belt deïŹector.
In this case, only use the child seat on the rear seat.
For the safety of your child, before every journey in the car check that...
âșthe child safety seat is engaged on sides with the ISOFIT locking arms both 15 in the
ISOFIT attachment points 01 and that both green safety buttons 04 are completely green;
âșthe child safety seat is securely fastened;
âșthe Top Tether 13 is tightly tensioned over the backrest of the car seat and the tensi-
on indicator 18 is green;
âșthe lap belt section 28 runs through the light red belt guides 23 on both sides of the
seat cushion;
âșthe diagonal seat belt section 11 on the side of the vehicle seat belt buckle 29 also
runs through the light red belt guide 23 of the seat cushion;
âșthe diagonal seat belt section 11 runs through the dark red belt holder 30 of the
headrest;
âșthe diagonal seat belt section 11 runs diagonally backward,
âșthe straps are tight and not twisted;
âșthe vehicle seat belt buckle 29 is not positioned between the light red belt guide 23
and the armrest of the seat cushion.
If your child attempts to open the safety buttons CAUTION! 04 or the harness
buckle 21 , make sure to stop at the earliest opportunity. Check that the child safety
seat is correctly attached and make sure that your child is properly secured. Teach
your child about the dangers involved.
GROUP 2 (15-25 kg) &
GROUP 3 (22-36 kg)
With ISOFIT + Top Tether + Vehicle belt
B
To remove the child seat follow the steps in section 8
15
04
29
11
28
23
28 23
11
30
07
11 07
7. Push the child seat towards the backrest applying ïŹrm, even
pressure on both sides.
8. Shake the child safety seat to make sure it is safely attached
and re-check the green safety buttons 04 to make sure that
both of them are completely green.
6. Grasp the child seat with both hands and slide the two
locking arms 15 ïŹrmly into the insert guides 02 until the lo-
cking arms engage with a clicking noise on both sides. The
green safety button 04 must now be visible on both sides.
The locking arms are only correctly engaged if CAUTION!
both of the safety buttons 04 are completely green.
1. Make sure that the child seatÂŽs 5-point harness is installed
correctly (see section 10).
2. Follow the steps in section 5.1
3. Follow the steps in section 5.2
4. Take the Top Tether 13 from the storage bag 14 and lay it
over the child seat.
5. Place the child seat facing in the direction of travel on the
vehicle seat.
GROUP 1 (9-18 kg) &
GROUP 2 (15-25 kg)
With ISOFIT + Top Tether + Vehicle belt + 5-Point Harness
A
6. INSTALLATION
13
14
15
04
9. Pull the Vehicle belt 22 out and guide it through the belt
guides 23 of the child seat. Make sure that the belt is not
twisted.
10. Engage the buckle tongue in the vehicle seat buckle 29 this
should make a click noise.
11. On the side opposite the car seat belt buckle, swivel clam-
ping lever 24 down and insert diagonal belt in belt lock-oî
25 .
12. Apply your body weight to the child seat (kneel into the
seat). At the same time pull the diagonal belt strongly to
tighten (hold tension) and swivel the clamping lever 24
upwards until it engages.
13. Remove body weight from child seat and re-tension by
pulling the diagonal belt with the belt lock-oî 25 closed.
14. Take the Top Tether 13 and press the metal tongue 16
away from the strap to lengthen the strap and pull the Top
Tether 13 by the snap hook 17 until it makes a V-shape.
15. Route the Top Tether 13 on the left and right hand sides of
the vehicle headrest.
16. Hook the snap hook 17 into the Top Tether anchoring point
recommended in your vehicle ownerâs guide.
Be sure not to use the luggage hook instead of CAUTION!
the Top Tether point. Check your vehicle and look for this
sign:
17. To Tension the Top Tether 13 remove the slack by pulling the
free end of the belt through the metal tongue 16 , equalising
the strap tension on both sides. The Top Tether is correctly
tensioned when the green tension indicator 18 is extended
by 1 cm.
18. Follow the steps in section securing your child with 5-point
harness.
22
23
24
25
25
17
16
29
1 cm
18
17
SECURING YOUR CHILD WITH 5-POINT HARNESS
21
26
08
19
21
27
7. CARE INSTRUCTIONS
To ensure the full protective eîect of the child safety seat:
âșIn the event of an accident with an impact speed above 10 km/h it is possible that the
child safety seat may have been damaged, but that the damage may not be immedia-
tely obvious. In this case the child safety seat must be replaced.
Please dispose of it properly.
âșRegularly check all important parts for damage. Make sure that the mechanical com-
ponents in particular are all in perfect working order.
âșTo prevent damage, ensure that the child safety seat does not become jammed bet-
ween hard objects (car door, seat runners etc.).
âșAlways have the child safety seat checked if it has been damaged (e.g. if it is drop-
ped).
âșNever lubricate or oil parts of the child seat.
âșIn order to properly protect your baby, it is imperative that you install and use the
ADVANSAFIX exactly as described in this manual.
Disposal of packaging Container for cardboard
Cover Residual waste, thermal utilisation
Plastic parts In accordance with the labelling in the designated container
Metal parts Container for metals
Harness straps Container for polyester
Buckle & latch Residual waste
8. REMOVAL OF THE CHILD SEAT
CAUTION! Remove the child seat from the vehicle. The child seat must never be
transported in the car if it is not properly secured.
Group 1 and Group 2 (ISOFIT, Vehicle belt & Top Tether)
1. To release the ISOFIT fastening, squeeze the green safety button and the red release
button together,ïŹrst on one side, then on the other.
2. Open the buckle of the vehicle seat belt and take the diagonal belt with a short pull
out of the belt lock-oî. This countermovement releases the interior clamping of the
belt lock-oî and the clamping lever is now easy to open.
3. To release the TopTether anchoring loosen the belt by lifting the metal tongue of the
adjuster away from the belt. Then take the spring hook out of the anchoring point.
4. Slide the ISOFIT locking arms back into the seat shell and put the connector protec-
tion on the ISOFIX.
Group 2 and Group 3 (ISOFIT & Top Tether)
1. Release vehicle seat buckle if securing the child seat.
2. To release the ISOFIT fastening, squeeze the green safety button and the red release
button together,ïŹrst on one side, then on the other.
3. To release the TopTether anchoring loosen the belt by lifting the metal tongue of the
adjuster away from the belt. Then take the spring hook out of the anchoring point.
4. Slide the ISOFIT locking arms back into the seat shell and put the connector protec-
tion on the ISOFIX
09
20
4. Make sure that your childÂŽs back
lies ïŹat against the backrest of
the child seat.
5. Guide the two buckle latches 20
together and engage them befo-
re putting them into the harness
buckle 21 - this should make a
click noise.
6. Pull shoulder straps 11 to remove all slack from the lap
section ensuring the harness lies ïŹat.
7. Pull on the adjuster strap 09 until the harness lies ïŹat and is
close against your childâs body.
CAUTION! Pull the adjuster strap 09 straight (not
upwards or downwards).
CAUTION! The harness straps 27 must be positioned as
low as possible over your childâs hips.
8. Pull down on the shoulder pads 19 to ensure they are correctly
positioned.
1. Open the harness buckle 21 (press red button)
2. Press the adjusting button 26 and at the same time pull both
shoulder belts 08 forwards. Do not pull on the shoulder pads
19 .
3. Have your child sit down in the child seat.
The more snugly the harness ïŹts over your childâs body, the better your child will be protected.
Therefore avoid putting thick clothes on your child under the belt.
To remove the child seat follow the steps in section 8
9. Take the Top Tether 13 and press the metal tongue 16 away
from the strap to lengthen the strap and pull the Top Tether
13 by the snap hook 17 until it makes a V-shape.
10. Route the Top Tether 13 on the left and right hand sides of
the vehicle headrest.
11. Hook the snap hook 17 into the Top Tether anchoring point
recommended in your vehicle ownerâs guide.
Be sure not to use the luggage hook instead of CAUTION!
the Top Tether point. Check your vehicle and look for this
sign:
12. To Tension the Top Tether 13 remove the slack by pulling the
free end of the belt through the metal tongue 16 , equalising
the strap tension on both sides. The Top Tether is correctly
tensioned when the green tension indicator 18 is extended
by 1 cm.
17
16
1 cm
18
17
13
14
11
19
03
15
0405
06
140826_ADVANSAFIX_EN_WIP_gb-GB.indd 1 26.08.2014 14:59:52
4. CARE AND MAINTENANCE
Care for the harness buckle
It is vital for the safety of your child that the harness buckle works correctly. Malfunctions
of the harness buckle are usually caused by accumulations of dirt or foreign bodies.
Malfunctions are as follows:
âą The buckle latches are ejected only slowly when the red release button is pressed.
âą The buckle latches will no longer lock home (i.e. they are ejected again if you try to
push them in).
âą The buckle latches engage without an audible âclickâ.
âą The buckle latches are diîcult to insert (you feel resistance).
âą The buckle only opens if extreme force is applied.
Remedy
wash out the harness buckle so that it functions properly once again:
Cleaning the harness buckle
1. Open the harness buckle 21 (press the red button).
2. Open the Velcro fastener on the crotch pad 32 and take oî the crotch pad from the
cover.
3. Put the seat shell into the recline position
4. Grasp the metal plate 33 from underneath and turn it into a vertical position
5. Slide the metal plate 33 through the slot 34
6. Remove the harness buckle 21
7. Soak the harness buckle 21 in warm water with washing-up liquid for at least an hour.
Then rinse and dry it thoroughly.
Cleaning
CAUTION Please be sure to use only genuine Britax replacement seat covers, as
the seat cover is an integral part of the child safety seat which plays an important role
in ensuring that the system works properly. Replacement seat covers are available from
your retailer.
CAUTION! The child seat must not be used without its cover.
âą The cover can be removed and washed with a mild detergent using the
washing machineâs cycle for delicate items (30 °C). Please observe the
instructions on the washing label of the cover.
âą The plastic parts can be cleaned using soapy water. Do not use harsh
cleaning agents (such as solvents).
âą The harnesses can be washed in lukewarm soapy water.
CAUTION! Never remove the buckle latches 20 from the straps.
âą The shoulder pads can be washed in lukewarm soapy water.
Removing the cover
A) Headrest
1. Move the headrest of the child seat to the upper position.
2. Take the elastic seam of the cover 35 from the hooks at the back side of the headrest
and remove the cover of the headrest.
B) Cover
1. Undo the hooks on the bottom side.
2. Undo the hooks located on the upper back side.
3. Undo the elastic loop on both sides of the belt guides.
4. Open the two plastic fasteners on the back side of the cover.
5. Remove the cover.
Re-ïŹtting the Cover:
Simply follow the steps in the opposite order.
CAUTION! ANever use the child seat in installation method without a correct instal-
led buckle. Make sure that the metal plate 33 is correctly attached.
CAUTION! Check that the harness straps are not twisted and that they
have been correctly inserted in the belt slots on the cover.
33
34
21 32
35
2. USE IN THE VEHICLE
Please observe the instructions on the use of child restraint systems described in
your vehicle ownerâs manual.
The seat may be used in vehicles equipped with ISOFIX ,Top Tether anchoring
systems and 3-point belt (see type list). Please consult your vehicle ownerâs
manual for information about the ISOFIX &Top Tether anchoring points and the
installation with 3-point belt. Also check your vehicle ownerâs manual for seats
which are approved for child safety seats in the weight classes 9-18 kg, 15-25 kg,
22-36 kg.
You can use your child car seat as follows:
In the direction of travel Yes
Against the direction of travel No 1)
with 2-point belt (Vehicle belt) NO
On seats featuring:
ISOFIX attachments (between seat surface and back-
rest), Top Tether anchoring points (for example on the
parcel shelf, on the ïŹoor or behind the backrest) and
3-point belt (Vehicle belt)
Yes 2) 3)
(Please observe the applicable regulations in your country)
1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only if
the vehicle seat is also approved for use by adults. The seat must not be positioned
anywhere where it is in range of an airbag which is being deployed.
2) The safety belt must be approved to ECE R 16 or a comparable standard (see test
label on belt with an âEâ or âeâ in a circle).
3) If there is a front airbag: Slide the passenger seat a long way back and refer to any
instructions in vehicle ownerâs manual.
1. GENERAL SAFETY NOTES
Take the time to carefully read through these instructions, and always
keep them ready to hand in the designated pocket on the child seat.
For the protection of all vehicle occupants
In the case of an emergency stop or an accident, persons or objects which are
not properly secured in the car can cause injury to other vehicle occupants.
For this reason, please always check that:
âą the backrests of the vehicle seats are locked (e.g. that the latch on a folding
rear seat bench is engaged).
âą all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
secured.
âą all persons in the vehicle have their seat belts fastened.
âą the child safety seat is always secured in the car via the ISOFIX anchoring,
the Top Tether and the 3-point belt (Vehicle belt) or the ISOFIX anchoring and
the Top Tether, even when there is no child in the seat
.
For the protection of your child
âą The more snugly the harness ïŹts over your childâs body, the safer your child
will be.
âą Please do not ever leave your child unattended in the child safety seat in the
vehicle.
âą Use on the rear seat:
Move the front seat forward far enough that you childâs feet cannot hit the
backrest of the front seat (to prevent risk of injury).
âą The child safety seat can get hot in direct sunshine. Childrenâs Caution:
skin is delicate and could be injured as a result. Protect the child seat against
intensive direct sunlight when it is not currently in use.
âą Only allow your child to enter and exit the vehicle on the pavement side.
âą Make stops during longer journeys to give your child an opportunity to run
about and play.
To protect your vehicle
Some vehicle seat coverings made of more delicate materials (e.g. velour,
leather, etc.) may develop wear marks when child seats are used. For optimum
protection of your seat covers, we recommend using the BRITAX Car Seat
Protector, which is available from our range of accessories.
3. APPROVAL
BRITAX
child safety seat
Tested and certiïŹed accord-
ing to ECE* R 44/04
Group Body weight
ADVANSAFIX 1 9 to 18 kg
2 15 to 25 kg
3 22 to 36 kg
The child safety seat has been designed, tested and certiïŹed according to the require-
ments of the European Standard for Child Safety Equipment (ECE R 44/04). The test
mark E (in a circle) and the certiïŹcation number are located on the orange certiïŹcation
sticker (sticker on the child safety seat).
âą This certiïŹcation will be invalidated if you make any modiïŹcations to the child safety
seat.
âą The ADVANSAFIX child safety seat must only be used to secure your child in the
vehicle. It must never be used as a seat or toy in the home.
Risk of injury due to unauthorised modiïŹcations!
Unauthorised technical modiïŹcations may reduce or entirely void the seatâs protective
properties.
âą Do not make any technical modiïŹcations to the child seat.
âą Use the child seat only as described in these user instructions.
The ADVANSAFIX oîers a variety of mounting options, the following table indicates the
types of installation for the respective groups:
Group Installation method Child installation User Guide
chapter
1 (9-18 kg) ISOFIT + TopTether +
Vehicle belt
with 5-point harness A
2 (15-25 kg) ISOFIT+ TopTether +
Vehicle belt
with 5-point harness A
2 (15-25 kg) ISOFIT + TopTether Vehicle belt B
3 (22-36 kg) ISOFIT + TopTether Vehicle belt B
1. Squeeze the adjustment handle 12 at the rear of the headrest 07 and push the
headrest into the lowest position.
2. Release the adjustment handle 12 to lock into place.
3. Lift the lower part of the headrest cover and place it over the headrest
4. Open the left and right buttons on the lower part of the cover 43 and lay the cover
piece on the seating area.
5. Take the shoulder belts 08 and the buckle latches 20 from the storage compart-
ment 47 and unroll the shoulder belts.
6. Fold back the two cover pieces and close the left and right poppers 42 on the
lower part of the cover.
Should the child seat not be in the most reclined position:
Press the recline handle so that the seat is in its most upright position.
7. Lift the harness buckle 21 and the shoulder pads 19 from the storage bag 14 on
the back side of the seat.
8. ReïŹtting harness buckle 21 and crotch pad 32 : pull the elastic strip 44 in the sea-
ting area towards you. Group 1 (9-18 kg) use the belt slot closest to the backrest a
for Group 2 (15-25 kg) use the one furthest away b.
9. Take the harness buckle 21 and hold the metal plate 33 verticaly. Push it with the
narrow side upwards through the belt slot a or b into the seat shell from above.
10. Ensure by looking underneath the seat that the metal plate 33 is in a horizontal posi-
tion and check the installation by pulling on the harness buckle 21 several times.
11. Guide the two buckle latches 20 together and engage them before putting them
into the harness buckle 21 - this should make a click noise.
CAUTION! The lap belts must not be twisted or swapped.
12. Thread the shoulder pads 19 onto the shoulder belts 08 in the correct orientation
as shown ensuring there are no twists. Allign the two loops of the shoulder belts 08
and strap loops of the shoulder pads 19 .
13. Pull the shoulder belts 08 and the strap loops of the shoulder pads 19 through the
slots 40 .
Tip: Fold up the rear cover part.
14. Pull the strap loops of the shoulder pads 19 onto the plastic extensions 41 of the
shoulder belt height adjuster 10 .Tip: the strap loops of the shoulder pads should
be the lower loop.
15. Fold the upper part of the cover downwards.
CAUTION! The shoulder belts 08 must not be twisted or swapped.
16. Take the connecting piece 39 from the provided storage on the back side of the
child seat.
17. Hook the shoulder belts 08 back onto the connecting piece 39 . The left loop on
the left arm of the connecting piece and the right loop on the right arm.
18. Pull slowly on the adjustment strap 09 and at the same time push the connecting
piece 39 between backrest and the provided storage of the connecting piece.
1. Put the storage bag 14 forward over the seat.
2. Loosen the 5-point harness 38 of the child seat as much as possible.
Back side of the child seat:
3. Press the button of the shoulder belt height adjuster 10 at the rear of the seat shell
and tilt the shoulder belt height adjuster 10 towards you.
4. Move the shoulder belt height adjuster 10 into the top position and ïŹx the position
by releasing the button of the shoulder belt height adjuster.
5. Loosen the 5-point harness 38 of the child seat as much as possible. Unhook the
shoulder belts 08 on the back side of the child seat from the connecting piece 39 .
6. Snap the connecting piece 39 in the provided storage.
7. Pull below both, the shoulder pads 19 and the two shoulder belts 08 to the front
through the slots 40 (front side of the child seat).
8. Slide the belt loops oî of the plastic extensions 41 of the shoulder belt height adjus-
ter 10 .
Front side of the child seat:
9. Pull out the adjuster strap 09 as far as possible.
10. Store the adjuster strap in the adjuster housing 26 .
11. Pull the shoulder pads 19 through the slots 40 to the front.
12. Remove the shoulder pads 19 from the shoulder belts 08 and put them in the
storage bag on the rear of the seat.
13. Open the harness buckle 21 (press the red release button)
14. Lift the lower part of the rear cover to the top and place it over the headrest.
15. Open the left and right poppers 42 on the lower part of the cover 43 and lift the
cover piece to the front. Slide the buckle latches 20 down into the storage compart-
ments.
16. Roll the shoulder belts 08 together and place them also into the storage compart-
ments.
17. Repositon the two cover parts to the rear and lock the poppers 42 on the left and
right side of the cover back side.
18. Lift the recline handle and pull at the front to fully recline the child seat.
19. Pull the elastic strip 44 over the harness buckle 21 .
20. Grasp the metal plate 33 from underneath and turn it into a vertical position.
21. Push upwards and slide the metal plate 33 through the slot 34 .
22. Remove the harness buckle 21 with the crotch pad 32 and store it in the storage
bag 14 .
9. REMOVING THE 5-POINT HARNESS
10. REFITTING THE 5-POINT HARNESS
38
10
39
08
39
19
08
40
41
10 26
09
40
19
08
21
42
43 08
42
12
07
42
43
33
34
44
21
32
21
14
2008
47
42
32
21
14
44
21
32
20
21
19
08
08 40
19
19
41
10
39 39
09
08
BRITAX RĂMER
Kindersicherheit GmbH
Blaubeurer StraĂe 71
D-89077 Ulm
Germany
t: +49 (0) 731 9345-199/-299
f: +49 (0) 731 9345-210
e: service.de@britax.com
www.britax.de
BRITAX EXCELSIOR LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
t: +44 (0) 1264 333343
f: +44 (0) 1264 334146
e: service.uk@britax.com
www.britax.eu
20
a
b
21
33
9 â 36 kg
9 m ~ 12 y
www.britax.eu
EDV-NR.: 2000012068 14/08
GB
User instructions
ADVANSAFIX
140826_ADVANSAFIX_EN_WIP_gb-GB.indd 2 26.08.2014 14:59:58
Produktspezifikationen
| Marke: | Britax |
| Kategorie: | Autositz |
| Modell: | Advansafix |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Britax Advansafix benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autositz Britax
21 August 2024
20 August 2024
17 August 2024
16 August 2024
15 August 2024
15 August 2024
15 August 2024
15 August 2024
15 August 2024
14 August 2024
Bedienungsanleitung Autositz
- Autositz Bugaboo
- Autositz Hema
- Autositz Dometic
- Autositz Baninni
- Autositz Bébé Confort
- Autositz Brevi
- Autositz Chicco
- Autositz Hauck
- Autositz Lorelli
- Autositz Biltema
- Autositz Quax
- Autositz Foppapedretti
- Autositz Quinny
- Autositz Fisher-Price
- Autositz Peg Perego
- Autositz Jane
- Autositz ABC Design
- Autositz Baby Jogger
- Autositz Joolz
- Autositz Giordani
- Autositz Stokke
- Autositz XOMAX
- Autositz Maxi-Cosi
- Autositz Cybex
- Autositz BabyGO
- Autositz Be Cool
- Autositz BeSafe
- Autositz Britax-Römer
- Autositz Inglesina
- Autositz Joie
- Autositz Kinderkraft
- Autositz Lionelo
- Autositz Safety 1st
- Autositz Casualplay
- Autositz Cosatto
- Autositz Gesslein
- Autositz Graco
- Autositz Kiddy
- Autositz Kikka Boo
- Autositz Mountain Buggy
- Autositz Nuna
- Autositz Phil And Teds
- Autositz Recaro
- Autositz StorchenmĂŒhle
- Autositz Cangaroo
- Autositz Caretero
- Autositz Axkid
- Autositz Concord
- Autositz Ellermeyer
- Autositz Klippan
- Autositz Nania
- Autositz Osann
- Autositz Petex
- Autositz Renolux
- Autositz UPPAbaby
- Autositz Silver Cross
- Autositz Sena
- Autositz Römer
- Autositz Dreambee
- Autositz GB
- Autositz Kiwy
- Autositz Migo
- Autositz Chipolino
- Autositz X-Adventure
- Autositz Diono
- Autositz Clek
- Autositz InfaSecure
- Autositz Disney
- Autositz Bertoni
- Autositz Evenflo
- Autositz Hamron
- Autositz Mother's Choice
- Autositz Kindercraft
- Autositz Burigotto
- Autositz Hipod
- Autositz Plebani
- Autositz Bellelli
- Autositz Xadventure
- Autositz Heyner
- Autositz Takata
- Autositz Avova
- Autositz Walser
- Autositz Apramo
Neueste Bedienungsanleitung fĂŒr -Kategorien-
14 Oktober 2024
5 Oktober 2024
30 September 2024
27 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
24 September 2024
23 September 2024