Brandt TG1089XC Bedienungsanleitung

Brandt Herde TG1089XC

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Brandt TG1089XC (22 Seiten) in der Kategorie Herde. Dieser Bedienungsanleitung war für 37 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/22
1
Gas Built-in Domino
Model TG1089XC
INSTALLATION INSTRUCTIONS
(FOR REGISTERED GAS INSTALLER ONLY)
&
USER AND OPERATOR INSTRUCTIONS
Installation must be in accordance with manufacturers’ instruction, relevant
Gas Fitting Regulations, AGA Installation Code for Gas Burning Appliances
and Equipment and any codes and regulations.
These instructions should be read carefully prior to initial use and retained in
a safe place in order that full advantage can be taken of the features of your
DOMINO
ANY SERVICING OF THE DOMINO & INSTALLATION MUST
BE CARRIED OUT BY A REGISTERED GAS INSTALLER.
YOUR HOB IS DELIVERED PRE-SET FOR TOWN GAS USE
A
A – English B - 中文
2
INSTALLATION INSTRUCTIONS
DATA PLATE DETAILS:
The data plate is located on the front side of the tray.
According to the Gas Safety Regulations of Hong Kong, any gas installation
works including the installation of appliances and connection tubing, must be
undertaken by registered gas installers who are registered for that appropriate
classes and be employed by registered gas contractors.
CHECK THAT THE DATA PLATE SHOWS THAT THE APPLIANCE IS
SUITABLE FOR THE AVAILABLE GAS SUPPLY.
1. Before installing the appliance check that the location provides the required
clearances from combustible materials and if necessary provide protection to
adjacent surfaces as required by the regulations. Make provision for the gas
supply to be connected in the position shown in Diagram A.
Diagram A Diagram B
Tray Dimensions (unit in mm) Cut out (unit in mm)
2. Cut the opening in the bench top to the dimensions shown in diagram B. The hob
must be built into the worktop of a support cupboard. This worktop must be at least 3
cm thick and heat-resistant or else coated with a heat resistant material. (Refer
Diagram C.) A side-clearance of at least 30 cm should be left to the right and left of
the hob. A tall cupboard or partition too close to the hob would hinder free movement
of kitchen utensils. If a horizontal partition is put under the hob, it must be placed
between 10 and 15 cm from the bottom of the worktop. In any case, do not keep any
sprays or pressurized containers in the compartment, which could be just under the
hob. Place the hob unit into the opening in the worktop by carefully pulling it
onwards you. Put the burners, caps and pan grates back into position.
Gas
supply
3
Diagram C
Overall dimension
description
If clearance between side
and rear walls and
periphery of the burner is
less than 150mm, the wall
must be protected with a
non-combustible material.
The protection must extend
a minimum distance of
450mm above the burner.
Horizontal surfaces less
than 730mm vertically
above the Domino must
also be protected.
Keep all natural air-vents open or have a mechanical ventilation system installed (a
mechanically ventilated hood).
- Prolonged, intensive use of the hob may require extra ventilation; by opening a window for
example or producing more efficient ventilation by increasing the power of the existing
mechanical ventilation (a minimum air input 2m3/hr per kW of gas energy is required)
For example: 5.0kW (total power) X 2 = 10 m3/h minimum flow rate required
3. Install the Domino in the cut-out (See diagram B).
4. The gas connection to the external gas governor is 1/2”BSP. Please ensure
sealing gasket/washer is in place while connecting to gas supply pipe.
Gas inlet


Produktspezifikationen

Marke: Brandt
Kategorie: Herde
Modell: TG1089XC

Brauchst du Hilfe?

Wenn Sie Hilfe mit Brandt TG1089XC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Herde Brandt

Bedienungsanleitung Herde

Neueste Bedienungsanleitung für -Kategorien-