Boss SD-1W Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Boss SD-1W (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
Owner’s Manual
Precautions When Connecting
5 To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
5 Once the connections have been completed, turn on power to
your various devices in the order specied. By turning on devices
in the wrong order, you risk causing malfunction and/or damage
to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
5 Due to the characteristics of its analog circuitry, this unit’s CHECK
indicator may be lit (eect on) or unlit (eect o) when you turn
the power on.
Use of Battery
5 A battery was installed in the unit before it left the factory. The life
of this battery may be limited, however, since its primary purpose
was to enable testing.
5 If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (supplied on a separate sheet).
5 When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
5 Batteries should always be installed or replaced before connecting
any other devices. This way, you can prevent malfunction and
damage.
Changing the Battery
1. Hold down the pedal and loosen the thumbscrew, then
open the pedal upward.
* The pedal can be opened without detaching the thumbscrew
completely.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
2. Remove the old battery from the battery housing, and
remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil
spring, and battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Specications
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output
Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance 10 kΩ or greater
Power Supply Carbon-zinc battery (9 V, 6F22) or
Alkaline battery (9 V, 6LR61)
AC adaptor (PSA series: sold separately)
Current Draw 15 mA
* Expected battery life under continuous use:
Carbon: 25 hours
Alkaline: 42 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 430 g / 1lb (including battery)
Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT
NOTES,” and “Information”)
Alkaline battery (9 V, 6LR61)
Options
(sold separately) AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
English
Main Features
Panel Descriptions
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
INPUT jack
This jack accepts signals coming from a guitar or other musical instrument, or
another eects unit.
* The INPUT jack doubles as the power switch.
Power to the unit is turned on when you plug into the INPUT jack; the
power is turned o when the cable is unplugged.
To prevent unnecessary battery consumption, be sure to disconnect the
plug from the INPUT jack when not using the eects unit.
AC Adaptor
(PSA series: optional)
Electric Guitar
Guitar Amplier
DC IN jack
Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without
being concerned about how much battery power you have left.
* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the correct
voltage. Do not use any other AC adaptor, since this may cause malfunction.
* If the AC adaptor is connected while a battery is installed, the power
supply is drawn from the AC adaptor.
* We recommend that you keep batteries installed in the unit even though
you’ll be powering it with the AC adaptor. That way, you’ll be able to
continue a performance even if the cord of the AC adaptor gets accidently
disconnected from the unit.
CHECK indicator
This indicator shows whether the eect is on or o, and also doubles as the battery check
indicator. The indicator lights when the eect is on.
* If you’re powering the unit with a battery and the CHECK indicator goes dim— or doesn’t
light at all—when you try to turn the eect on, the battery is near depletion and should be
replaced. For instructions on changing the battery, refer to “Changing the Battery.”
OUTPUT jack
Connect this jack to your amp or to the input of another eect unit.
Pedal switch
This switch turns the eect on/o.
Thumbscrew
When this screw is loosened, the pedal
will open, allowing you to change the
battery.
* For instructions on changing the
battery, refer to “Changing the
Battery.”
LEVEL knob
Adjusts the volume when the eect is on.
TONE knob
Adjusts the brightness of the eect sound. Turning the knob clockwise
brightens the sound.
DRIVE knob
Adjusts the amount of overdrive. Turning the knob clockwise increases the eect
(distortion).
Mode switch
Switches the tonal character.
S (standard) The original tone of the SD-1.
C (custom) A custom tone that broadens the range and slightly
boosts the gain.
© 2014 Roland Corporation 02
7This is a “WAZA CRAFT series” eect unit featuring analog circuitry painstakingly designed in every detail for the best possible sound.
7The amp circuit consists entirely of discrete components; no op-amps are used.
7In addition to the sound of the original SD-1, you’ll enjoy a custom tone that’s been fully tuned-up by BOSS engineers.


Produktspezifikationen

Marke: Boss
Kategorie: Nicht kategorisiert
Modell: SD-1W

Brauchst du Hilfe?

Wenn Sie Hilfe mit Boss SD-1W benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Boss

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-