Boss RC-1 Bedienungsanleitung

Boss Nicht kategorisiert RC-1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Boss RC-1 (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

Owner’s Manual

* 5100069045- 01*

Basic Operation

To perform recording, overdubbing, and playback, press the pedal as shown in the diagram.

Technique for stopping

Example: When you want to stop at the end of a

measure with a 4/4 time signature

Press the pedal one time at the beginning of

the fourth beat, then press it once again at the

beginning of the rst beat of the next measure.

1st time 2nd time

1 2 3 4 1

Stop

Loop Playback

Play back a phrase as a loop.

Pressing the pedal switches

the unit to overdubbing.

Overdubbing

Layer your performances while

the phrase plays as a loop.

Pressing the pedal switches the

unit to playback.

Recording

Record your

guitar or bass

performance.

Stop

During overdubbing or loop playback, you

can stop by pressing the pedal twice in

succession.

* Press the pedal twice within one second.

Press twice

Lit red and

green

Lit greenLit red

Deleting a Phrase

The recorded phrase is erased if you hold down the pedal for two seconds or

longer while stopped.

During erasure, the LOOP indicator (red) blinks rapidly.

* Never turn o the power while the LOOP indicator (red) is blinking rapidly. The

recorded data might be lost if you do so.

* The phrase plays while you hold down the pedal. If you want to erase the

phrase without playing it, use an external footswitch to stop the phrase.

Cancelling an Overdub (Undo/Redo)

You can undo/redo by holding down the pedal for two seconds or longer during

overdubbing or playback.

Operation Explanation

Undo Cancels the last recording or overdub.

Redo

To bring back the cancelled sound, hold down the pedal once

again for two seconds or longer during playback.

* Redo is possible only during overdubbing or playback.

During undo/redo, the LOOP indicator (green) blinks rapidly.

Connecting to an External Footswitch

Connect your footswitch to the STOP/UNDO jack as shown in the illustration, and

set its POLARITY switch.

* The FS-5L cannot be used.

FS-7

FS-6

FS-5UFS-5U

1/4” phone type

10 1/4” phone

type

Stereo 1/4” phone

type 1/4” 10

phone type x 2

Stereo 1/4” phone

type Stereo 1/4” 10

phone type

Footswitch Operation

FS-5U Stop

During recording/overdubbing/playback,

press the footswitch to stop.

Erase the phrase

Hold down the footswitch two seconds or

longer to erase the phrase.

FS-5U/FS-7 pedal connected

to the stereo L side

FS-6’s pedal B

FS-5U/FS-7 pedal connected

to the stereo R side Undo/Redo

You can undo/redo by pressing the footswitch.

FS-6’s pedal A

Changing the Recording Mode/Stop Mode/Display Mode

1. While holding down the pedal switch, turn the power on (insert a plug into

the OUTPUT A jack).

The LOOP indicator (red) lights, indicating the current recording mode.

Recording mode Explanation

Red

Upper

half

Switch in the order of recording overdubbing 0

0 playback.

Lower

half

Switch in the order of recording playback 0 0

overdubbing (default setting).

2. Press the pedal switch successively twice (within one second) to change the

recording mode.

3. Press the pedal switch.

The LOOP indicator (green) lights, indicating the current stop mode.

Stop mode Explanation

Green

Upper

half

Press the pedal switch successively twice to stop

immediately (default setting).

Lower

half

Press the pedal switch successively twice to

enable stopping at the end of the phrase;

playback stops when the phrase has played to its

end. When playback stops, the phrase is erased.

Operation when stop has been enabled

• The LOOP indicator (green) rotates while

blinking.

• Press the pedal switch successively twice to

stop immediately and erase the phrase.

• Hold down the pedal switch for two seconds

or longer to cancel the stop-enabled state.

4. Press the pedal switch successively twice (within one second) to change the

stop mode.

5. Press the pedal switch.

The LOOP indicator (red and green) lights, indicating the current display mode.

Display mode Explanation

Red

and

Green

Upper

half

The rotational speed of the LOOP indicator

changes according to the length of the recorded

phrase (default setting).

Lower

half

The LOOP indicator rotates rapidly; then the

playback location blinks.

6. Press the pedal switch successively twice (within one second) to change the

stop mode.

7. When the power is turned o and on again, the unit returns to normal

operation.

Changing the Battery

1. Hold down the pedal and loosen the

thumbscrew, then open the pedal upward.

* The pedal can be opened without detaching

the thumbscrew completely.

2. Remove the old battery from the battery

housing, and remove the snap cord

connected to it.

3. Connect the snap cord to the new battery,

and place the battery inside the battery

housing.

* Be sure to carefully observe the battery’s

polarity (+ versus -).

4. Slip the coil spring onto the spring base on

the back of the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely.

Specications

BOSS RC-1: Loop Station

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output Level -20 dBu

Output Impedance 1 kΩ

Recommended Load Impedance 10 kΩ or greater

Maximum Recording Time Approx. 12 minutes

Power Supply DC 9 V: Alkaline battery (9 V, 6LR61), AC Adaptor (PSA

series: sold separately)

Current Draw

95 mA * Expected battery life under continuous use:

Alkaline: Approx. 3 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 430 g/1 lb (including battery)

Accessories

Owner’s Manual,

Leaet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,”

and “Information”), Alkaline battery (9 V, 6LR61)

Options (sold separately) AC adaptor: PSA series

Footswitch: FS-5U, FS-6, FS-7

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the time that the document was

issued. For the latest information, refer to the Roland website.

About the Battery

• Batteries should always be installed or replaced before connecting any other devices. This way,

you can prevent malfunction and damage.

• The use of an AC adaptor is recommended as the unit’s power consumption is relatively high.

Should you prefer to use battery, please use the alkaline battery.

• If you handle batteries improperly, you risk explosion and uid leakage. Make sure that you

carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES.”

Repairs and Data

• Although we will do our utmost to preserve the data stored in your unit when we carry out

repairs, in some cases, such as when the memory section is physically damaged, restoration of

the stored content may be impossible. Roland assumes no liability concerning the restoration

of any stored content that has been lost.

Intellectual Property Right

• It is

forbidden by law to make an audio recording, video recording, copy or revision of a third

party’s copyrighted work (musical work, video work, broadcast, live performance, or other

work), whether in whole or in part, and distribute, sell, lease, perform, or broadcast it without

the permission of the copyright owner.

• Do not use this product for purposes that could infringe on a copyright held by a third party.

We assume no responsibility whatsoever with regard to any infringements of third-party

copyrights arising through your use of this product.

• Roland, BOSS, and Loop Station are either registered trademarks or trademarks of Roland

Corporation in the United States and/or other countries.

• Company names and product names appearing in this document are registered trademarks or

trademarks of their respective owners.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

DC IN jack

Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without being

concerned about how much battery power you have left.

* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the

correct voltage. Do not use any other AC adaptor, since this may cause malfunction.

* If the AC adaptor is connected a battery is installed, the power supply is drawn from the AC

adaptor.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it

with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the

AC adaptor gets accidently disconnected from the unit.

CHECK indicator

This indicator shows the power on/o status, and also provides a battery check function.

* If you’re powering the unit with a battery and the CHECK indicator goes dim—or doesn’t light at all—the battery is

near depletion and should be replaced. For instructions on changing the battery, refer to “Changing the Battery.”

Panel Descriptions

OUTPUT jacks A (MONO)/B

Connect these jacks to your amp or monitor speakers.

If you’re using a mono setup, use the OUTPUT A jack.

* The OUTPUT A jack also operates as a power switch. The power

will be on if a plug is inserted in the OUTPUT A jack. Remove the plug

when you’re not using the RC-1.

* Do not connect headphones to the OUTPUT jacks. Doing so may

damage the headphones.

Thumbscrew

When this screw is loosened, the pedal will open,

allowing you to change the battery.

* For instructions on changing the battery, refer to

“Changing the Battery.”

INPUT jacks A (MONO)/B

Connect your electric guitar, or another instrument or eect unit, to these jacks.

LEVEL knob

This adjusts the volume level of the loop phrase being played back.

* The input level from the INPUT jacks cannot be adjusted.

AC Adaptor

(PSA series: sold

separately)

Guitar

Amplier

* Use the INPUT A jack and INPUT B jack when

connecting a stereo-output eects unit. Use only

the INPUT A jack if you’re using a mono source.

MEMO

• If a footswitch is connected to the STOP/UNDO jack, you can stop by

pressing the footswitch just once.

• The recorded phrase is saved even if you turn o the power.

NOTE

• The minimum recording time for a loop phrase is approximately 0.25

seconds. If you press the pedal within approximately 0.25 seconds after

you start recording, recording will continue until the phrase is at least

approximately 0.25 seconds long.

• The maximum recording time for a loop phrase is approximately 12

minutes (stereo). If you exceed the maximum recording time, recording

or overdubbing is interrupted, and operation changes to loop playback.

• Roland assumes no liability concerning the restoration of any stored

content that has been lost.

Pedal switch

This pedal switches you between phrase recording, overdubbing, and playback. Press

the pedal twice in succession to stop playback.

If you hold down the pedal two seconds or longer while stopped, the recorded phrase

is erased.

STOP/UNDO jack

If you connect a footswitch (FS-5U, FS-6, FS-7: sold separately), you can

use it to stop playback or to undo/redo.

LOOP indicator

This lights during recording, overdubbing, and playback.

Indicator Explanation

Red During recording

Red and green During overdubbing

Green During playback

* During overdubbing/playback,

the speed at which the indicator

rotates corresponds to the length

of the loop.

English

Precautions When Connecting

* To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units before making any

connections.

* Raise the amp volume only after turning on the power to all connected devices.

* When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the

battery as soon as possible.

* When connection cables with resistors are used, the volume level of equipment connected to the INPUT jacks may be low.

If this happens, use connection cables that do not contain resistors.

Caution When Connecting an External Footswitch

You must power-o the unit before connecting an external footswitch.

If you connect the footswitch while the power is on, recorded data might be lost.

Turning On the Power

Inserting a connecting plug into the OUTPUT A jack turns on the power to the unit.

Once the connections have been completed, turn on power to your various devices in the order specied. By turning on

devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

* This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will

operate normally.

* Before turning the unit on/o, always be sure to turn the volume down. Even with the volume turned down, you might

hear some sound when switching the unit on/o. However, this is normal and does not indicate a malfunction.

Caution when turning o the power

Never turn o the power while the LOOP indicator is rotating or blinking (i.e., don’t pull the plug out of the OUTPUT A

jack). The recorded data might be lost if you do so.

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

Electric Guitar

Produktspezifikationen

Marke:	Boss
Kategorie:	Nicht kategorisiert
Modell:	RC-1
Breite:	73 mm
Tiefe:	129 mm
Gewicht:	430 g
Produkttyp:	Expressionspedal
Produktfarbe:	Rot
Höhe:	59 mm
Energiequelle:	AC,Battery
Gleichstrom-Anschluss (DC):	Ja
Betriebsanleitung:	Ja
Energieverbrauch:	95 mA
Anzahl unterstützter Akkus/Batterien:	1
Akku-/Batteriespannung:	9 V
6,35 mm (1/4-Zoll) Eingang:	3
Rutschfeste Oberfläche:	Ja
Beste Verwendung:	Gitarre
Synchronisations-Eingangsimpedanz:	1000000 Ohm
Output Widerstand:	1000 Ohm
6,35 mm (1/4-Zoll) Ausgang:	2
Ausgangspegel:	-20/0 dB
Nominales Input level:	-20 dB
Status-LED-Anzeige:	Ja