Boss DD-3T Bedienungsanleitung

Boss Nicht kategorisiert DD-3T

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Boss DD-3T (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/1
INPUT jack (Power switch)
Inputs the sound to which delay is applied. Connect your electric guitar,
other instrument, or eect unit here.
About power on/o
The INPUT jack also serves as the power
switch. Power is turned on whenever a plug is
inserted into the INPUT jack, and is turned o
when the plug is disconnected.
* To prevent unnecessary battery consumption, be sure
to disconnect the plug from the INPUT jack when not
using the unit.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
English
OUTPUT jack
Outputs a mix of direct sound and delay sound. Connect this to your
guitar amp or eect unit.
* If a device is connected to the DIRECT OUT jack, only
the delay sound is output.
CHECK indicator
Indicates the on/o status of the eect or the short loop function, and also provides a battery check
function. The indicator is lit red when on, and unlit when o.
* When operating on battery power only, the unit’s indicator will become dim when battery power gets too low.
Replace the battery as soon as possible.
[FEEDBACK] knob
Adjusts the feedback level. Turning the knob clockwise increases
the number of repetition of delay sound. Turning the knob fully
counterclockwise produces single delay sound.
Thumbscrew
When the thumbscrew is loosened, the
pedal will open, allowing you to change
the battery.
* A battery was installed in the unit before
it left the factory. The life of this battery
may be limited, however, since its primary
purpose was to enable testing.
[MODE] knob, [TIME] knob
Use the [MODE] knob to choose the mode.
When MODE = S. 50ms, M. 200ms, L. 800ms
Switches the delay time range between three settings. Use the [TIME]
knob to adjust the delay time. Turning the knob clockwise lengthens
the delay time.
MODE Minimum value Maximum value
S. 50ms 12.5 msec 50 msec
M. 200ms 50 msec 200 msec
L. 800ms 200 msec 800 msec
When MODE = SHORT LOOP
The sound immediately prior to pressing the pedal switch is played as
a loop as long as you hold down the pedal switch (short loop function).
Use the [TIME] knob to adjust the loop time (200–800 msec).
* If you change the loop time while the loop is playing, the pitch of the loop
sound changes.
DIRECT OUT jack
Outputs the direct sound. Connect this to your guitar amp, etc.
* Delay sound is output from the OUTPUT Jack.
[E.LEVEL] knob
Adjusts the volume of the delay sound. Turning the knob clockwise
increases the delay sound. If the knob is turned all the way clockwise,
the delay sound has the same volume as the direct sound.
If the knob is turned all the way counterclockwise, no delay sound is
output.
DC IN jack
Accepts connection of an AC Adaptor (sold separately: PSA series). By using an AC Adaptor,
you can play without being concerned about how much battery power you have left.
* We recommend that you keep batteries installed in the unit even though you’ll be powering it
with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the
AC adaptor gets accidentally disconnected from the unit.
* Use only the specied AC adaptor (PSA series).
* If the AC adaptor is connected while power is on, the power
supply is drawn from the AC adaptor.
Owner’s Manual © 2019 Roland Corporation
Panel Descriptions
* 5 1 0 0 0 6 7 6 6 9 - 0 1 *
Pedal switch
Turns the eect or the short loop function on/o.
When setting the delay time to match the tempo of your song (tempo
delay), this is used to enter the tempo.
TEMPO jack
Connect a footswitch (sold separately: FS-5U, FS-6, FS-7). You can use a footswitch to enter the tempo.
* Only one footswitch can be connected. If you’re using the FS-6/FS-7, connect either the A jack or the B jack.
* Make this connection using a 1/4” plug cable (1/4” phone plug ,1/4” phone plug).
* Set the mode/polarity switches as shown in the illustration below.
FS-5U FS-6 FS-7
B A
Precautions When Connecting
5 To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
5 Do not use connection cables that contain a built-in resistor.
5 Once everything is properly connected, be sure to follow the
procedure below to turn on their power. If you turn on equipment
in the wrong order, you risk causing malfunction or equipment
failure.
When powering up
Turn on the power to your guitar amp last.
When powering down
Turn o the power to your guitar amp rst.
5 Before turning the unit on/o, always be sure to turn the volume
down. Even with the volume turned down, you might hear some
sound when switching the unit on/o. However, this is normal and
does not indicate a malfunction.
About Output
7 Connect to the OUTPUT jack only
The direct sound + delay sound is output.
DD-3T
7 Connect to the OUTPUT jack and the DIRECT OUT jack
The delay sound is output from the OUTPUT jack, and the direct
sound is output from the DIRECT OUT jack.
DD-3T
Direct soundDelay sound
7 Connect to the SEND/RETURN jacks of a guitar amplier
If you’re using this unit in a parallel-connected eect loop, insert a
dummy plug into the DIRECT OUT jack so that only the delay sound
is output to the RETURN jack.
RETURN
Dummy plug
SEND
INPUT
DD-3T
Using the Tempo Delay
By pressing the pedal switch or an external footswitch several times
in rhythm with your song, you can set the delay time to match the
tempo of the song (tempo delay)
MEMO
5 The delay time range is 133–800 msec (BPM = 75–300).
5 The delay time specied by tempo input is maintained until you operate
the [TIME] knob.
Using the pedal switch
* If a footswitch (sold separately) is connected to the TEMPO jack, you
can’t use the pedal switch to enter the tempo.
1. Use the [MODE] knob to specify the note value that will be the
basis of the delay time.
MODE Note length
S. 50ms Quarter note triplet
M. 200ms Dotted eighth note
L. 800ms Quarter note
2. Hold down the pedal switch for two seconds or longer.
The CHECK indicator is lit green, and now you can use the pedal
switch to enter the tempo.
* Tempo entry is not possible if the [MODE] knob is set to “SHORT LOOP.”
3. Press the pedal switch at quarter-note intervals in
synchronization with the tempo of the song.
According to the tempo that you enter, the delay time is set so
that it is the length of the note value that you specied with the
[MODE] knob.
The CHECK indicator blinks at the specied tempo.
4. To nish inputting the tempo, hold down the pedal switch for
two seconds or longer.
Using an external footswitch
Basic operation is the same as when using the pedal switch.
1. Connect a footswitch (sold separately: FS-5U, FS-6, or FS-7) to
the TEMPO jack.
2. Use the [MODE] knob to specify the note value that will be the
basis of the delay time.
3. Press the footswitch at quarter-note intervals in synchronization
with the tempo of the song.
The delay time is set, and the CHECK indicator blinks at the
specied tempo.
Changing the Battery
* Batteries should always be installed or replaced before connecting any
other devices. This way, you can prevent malfunction and damage.
* If you handle batteries improperly, you risk explosion and uid leakage.
Make sure that you carefully observe all of the items related to batteries
that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES”
(supplied on a separate sheet).
Thumbscrew
Battery housing
Pedal
Spring base
Coil spring
Guide bush hole
Battery snap cord
Battery snap
9 V battery
1. Hold down the pedal and loosen the thumbscrew, then open
the pedal upward.
2. Remove the old battery from the battery housing, and remove
the snap cord connected to it.
3. Connect the snap cord to the new battery, and place the
battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus –).
4. Slip the coil spring onto the spring base on the back of the
pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil spring,
and battery housing.
5. Finally, insert the thumbscrew into the guide bush hole and
fasten it securely.
Main Specication
BOSS DD-3T: Digital Delay
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance 10 kΩ or greater
Power Supply
Carbon-zinc battery (9 V, 6F22) or Alkaline battery
(9 V, 6LR61)
AC adaptor (PSA series: sold separately)
Current Draw
45 mA
Expected battery life under continuous use
Alkaline Approx. 11.5 hours
Carbon Approx. 3 hours
* These gures will vary depending on the actual
conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight
(including battery)
420 g
15 oz
Accessories
Owner’s Manual, Leaet (“USING THE UNIT SAFELY,”
“IMPORTANT NOTES,” and “Information”), Alkaline
battery (9 V, 6LR61)
Options
(sold separately)
AC adaptor: PSA series
Footswitch: FS-5U, FS-6, FS-7
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the time that
the document was issued. For the latest information, refer to the Roland
website.
AC adaptor (sold
separately: PSA series)
Electric guitar
Guitar amplier
Guitar amplier
Footswitch
(FS-5U etc.)
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
DD-3T
Guitar Eects
Roland Corporation U.S.
5100 S. Eastern Avenue Los Angeles, CA 90040-2938
(323) 890-3700
SUPPLIER’S DECLARATION OF CONFORMITY
Compliance Information Statement
For the USA

Produktspezifikationen

Marke: Boss
Kategorie: Nicht kategorisiert
Modell: DD-3T

Brauchst du Hilfe?

Wenn Sie Hilfe mit Boss DD-3T benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Boss

Boss

Boss PW-3 Bedienungsanleitung

4 September 2024
Boss

Boss BCAM60 Bedienungsanleitung

3 September 2024
Boss

Boss ME-90B Bedienungsanleitung

3 September 2024
Boss

Boss TU-80 Bedienungsanleitung

31 August 2024
Boss

Boss Reverb RV-6 Bedienungsanleitung

31 August 2024
Boss

Boss Reverb RV-200 Bedienungsanleitung

28 August 2024
Boss

Boss GKC-AD Bedienungsanleitung

26 August 2024
Boss

Boss GT-1000CORE Bedienungsanleitung

26 August 2024
Boss

Boss Pocket GT Bedienungsanleitung

26 August 2024
Boss

Boss GKC-DA Bedienungsanleitung

26 August 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024