Boss BPLCAM Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Boss BPLCAM (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
REAR VIEW MOTORCYCLE
LICENSE PLATE MOUNT CAMERA
FEATURING HIDDEN MOUNTING BRACKET
BPLCAM
USER’S MANUAL
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech Support: www.bossaudio.com/support
0121
DO NOT FULLY RELY ON REVERSE CAMERA
WHEN BACKING UP.
ALWAYS CHECK YOUR SURROUNDINGS
BEFORE BACKING UP.
SPECIFICATIONS
Power Supply DC 12v
Lens Angle (Deg.) 17
TV System NTSC
Video Output 1.0vp-p, 75
S/N Ratio < 48 dB
IP Rating IP68
Operating Temp. (Deg. C) -30ºC ~ +70ºC (RH 95% Max.)
White Balance Auto
Minimum Illumination 0.5 LUX
AGC Auto
Resolution (TV Lines) 480
Electronic Shutter 1/60 (NTSC)
Eective Pixels 628 x 586
Above parameters can be modified without notification.
TROUBLESHOOTING GUIDE
The following checklist might help to solve the problems when
using this unit. Please double check to ensure connection and
procedure of operation is done properly before using checklist.
PROBLEM CAUSE/SOLUTION
NO IMAGE Check that power cable is securely connected.
Check to ensure there is a good connection
between video-in and monitor.
Check that REVERSE GEAR is engaged.
Check to ensure correct monitor setup.
IMAGE BLURRING Check for water/water stain or dust on
camera lens.
Clean camera lens
IMAGE SHAKING Check to insure camera is mounted and
secured tightly.
IMAGE SLANTED Adjust camera mounting bracket
INSTALLATION
Complete all required connections so that all lines are
hidden in vehicle.
Power/Video
Red and black back lights 12V line
Camera
DC 12V
DC 12V
VIDEO
NOTE:
If problems persist – consult nearest service dealer. DO NOT attempt
to disassemble or modify unit.
1. WIRE CONNECTION
2. CAMERA INSTALLATION
Camera should be installed in the following configuration:
License Plate Frame Mount – Align camera frame with top-set of
screw holes on license plate or license plate frame. Affix camera
using license plate mount screws. See: (diagram 1)
Attention: The camera switch is controlled by reverse gear shift.
3. TO REMOVE THE DISTANCE GUIDE LINES (Optional):
1. Turn the system OFF before proceeding.
2. Cut the white loop wire located at the connection points
(camera end).
3. Insulate the wire, using tape or crimp connectors on both ends.
4. Reconnecting the wire will display the guide lines again.
4. TO INVERT CAMERA IMAGE:
1. Turn the system OFF before proceeding.
2. Cut the blue loop wire located at the connection points (camera end).
3. Insulate the wire, using tape or crimp connectors on both ends.
4. Reconnecting the wire will orient the image back to its original
position.
License Plate
Frame
(diagram 1)


Produktspezifikationen

Marke: Boss
Kategorie: Nicht kategorisiert
Modell: BPLCAM

Brauchst du Hilfe?

Wenn Sie Hilfe mit Boss BPLCAM benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Boss

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-