Bogen MPS1 Bedienungsanleitung

Bogen Lautsprecher MPS1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Bogen MPS1 (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Specifications subject to change without notice.

54-2194-01A 1010

MPS1

Mini Pendant Speaker

Models MPS1B /MPS1W

Installation and Use Manual

Power Tap Selection

16-ohm or 70V

The Power Tap selector switch is used to set the

appropriate power level or impedance for your

system. Rotate the switch until the power level

you require lines up with arrow.

IMPORTANT: When connecting to a 70V amplifier,

make sure that the MPS1 Tap Selector switch

IS NOT set in the “16Ω” position.

Speaker Connection and Polarity

Speaker wiring is terminated at a snap-lock input

connector, with a positive and negative terminal.

All wiring should be done prior to installation and

then plugged into the rear of the MPS1. Wire all

speaker polarities the same way.

70V System Configurations

When designing a 70V system, the total of all power tap settings of all the connected

speakers CANNOT EXCEED the output power of the 70V amplifier (amplifier power

can exceed the sum of the speaker loads).

Low-Impedance System Configurations

When wiring together multiple MPS1 speakers that are set to 16 ohms, it is important to

calculate (using Ohmʼs Law) the total load that these speakers present to the amplifier.

The total load impedance of the interconnected speakers cannot be lower than the

minimum load impedance rating of the low-impedance amplifier. Also, care must be

taken to ensure the amplifier cannot overdrive the speakerʼs maximum power rating.

POWER TAP

SELECTOR SWITCH

SNAP-LOCK

WIRING TERMINAL

MPS1

(Top View)

EXAMPLE: 16 + 32 + 8 + 8 + 16 = 80 Watts minimum amplifier output rating.

EXAMPLE: Four 16 -ohm speakers in parallel = 4 ohms. Also in this example,

the maximum amplifier output power rating should not exceed 200W (4 X 50W,

the MPS1 max. power is 50W).

__ +

IMPORTANT:

The MPS1 Mini Pendant is not an outdoor speaker. DO NOT expose the

speaker to rain or moisture. The MPS1 should be installed by qualified personnel.

ALONG WITH THE MAIN DROP CABLE, YOU MUST ALSO USE A

SAFETY CABLE WHEN SUSPENDING AN MPS1 PENDANT SPEAKER.

BE SURE TO SECURE

ALL RIGGING POINTS AND FOLLOW ALL

THE CABLE MANUFACTURER’S

MATERIAL RECOMMENDATIONS

& INSTALLATION INSTRUCTIONS. FAILURE TO DO SO MAY RESULT

IN PROPERTY DAMAGE, INJURY

OR DEATH, AND LEGAL LIABILITY

FOR YOU AND/OR YOUR COM

PANY.

Attach the main drop cable to the MPS1 Main Drop Cable hole in the Suspension

Attachment located on the top of the speaker. This Main Drop Cable will be the primary

connection that will hold all the suspended speakerʼs weight to the anchor point.

Likewise, attach the Safety Cable to the Safety Cable hole in the Suspension Attachment.

This Safety Cable is meant to be a safeguard only, so when attaching to an anchor point

allow for a small amount of slack in the wire, as the Safety Cable should not bear any of

the speakerʼs direct supension weight to keep the speaker hanging level.

MPS1 Speaker Cable Connections

and Suspension Instructions

In addition to the Main suspension Drop Cable,

a backup Safety Cable is required for proper

installation. Use wire rope or other drop line rated

for at least 100 lbs. to ensure a safety

margin.

The attachment point on the structure from which

the speaker is to be anchored also must be able

to handle 100 lbs.

NOTE:

If using suspension cables with a cladding,

be sure to strip away coating where any clamping

device is being used so that bare wire cores of the

cable are being clamped.

MAIN DROP

CABLE HOLE

MPS1

MINI PENDANT

SPEAKER

MPS1 SUSPENSION

ATTACHMENT

SAFETY

CABLE HOLE

MAIN

DROP

CABLE

SAFETY

CABLE

TO SPEAKER

ANCHOR

POINT

Produktspezifikationen

Marke:	Bogen
Kategorie:	Lautsprecher
Modell:	MPS1
WLAN:	Nein
Bluetooth:	Nein
Gewicht:	2041 g
Empfohlene Nutzung:	Universal
Produktfarbe:	Weiß
Übertragungstechnik:	Kabelgebunden
Impedanz:	16 Ohm
Höhe:	7.875 Zoll
Energiequelle:	AC
RMS-Leistung:	50 W
Gehäusematerial:	ABS Synthetik
Audio Kanäle:	1.0 Kanäle
Energiebedarf:	70V
Anzahl des Antriebs:	1
Frequenzbereich:	50 - 14000 Hz
Anzahl enthaltener Produkte:	1 Stück(e)
Lautsprecherplatzierung:	Deckenmontage möglich
Subwoofer-Treiberdurchmesser (imperial):	4.5 Zoll
Lautsprechergehäuse:	Geschlossen
Empfindlichkeit:	85 dB
Tiefe (imperial):	12 Zoll
Breite (imperial):	12 Zoll