Blaupunkt DC-S3 Bedienungsanleitung

Blaupunkt Sicherheitskamera DC-S3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Blaupunkt DC-S3 (2 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Door/Window and Shutter Detector with Wire Input (DC-S3)

1. LED indicator & Learn/Test Button

Press the button to transmit a learn/test code and enter Test

mode for 3 minutes. The LED will light up whenever the Detector

is activated der Test mode.un

2. Mounting Holes (Covered by White Caps)

3 Wire Input Terminial 1 .

Connect the terminal to any Normal Close (N.C) device

4. Wire Input Terminial 2

Connect the terminal to Roller Shutter

5. Jumper Switches

For Jumper Switch functions, refer to later section “Jumper

Switch Setting”.

6 Battery Insulator .

7. Tamper Switch

8. Knockout for Extension Terminals

9. Rib-Mark

10. Magnet

1 x Door Contact

2 x wall plugs and screws

1 x adhesive pads

1 x 3V lithium battery (pre-installed)

Put the Control Panel into learning mode, then press the learn

button to transmit learn code. Please refer to Control Panel

manual to complete learn in process.

The Detector can be used either as a door/ window sensor or

transmitter for shutter or wired device, or all at the same time.

Choose the mounting location according to the Door Contact’s

usage.

 As a Door/window sensor: mount the main body on the

door/window frame, and the magnet on the door/window.

Mount as high as possible.

 As a transmitter for shutter or wired device: mount close

to the device accordingly.

 Do not mount on metallic surface.

1. Remove the white caps covering the 2 mounting holes.

2. Drill holes into the mounting location using the holes as

template.

3. Screw the sensor onto the wall or door/window frame with the

screws and plugs provided.

As a Door/ Window Sensor

4. Align the magnet with the Rib Mark on main body; screw the

magnet onto the door/window or apply with double-side

adhesive tape. The gap between the body and the magnet

should be no more than 15 mm.

As a Transmitter

5. Break through the knockout at top of the cover

6. For general wired device: connect the wire from device to

Wire Input Terminal . Multiple wired devices can be 1

connected to single Door Contact as long as the devices form

a closed loop with the Detector (Figure A)

7. For roller shutter: connect the wire from roller shutter to Wire

Input Terminal 2. (Figure B)

Figure A Figure B

8. Replace the white caps.

IInnssttaallllaattiioonn

Frame

Door/

Window

After installation, the Detector will be activated under the

following conditions:

1. When the door is opened and magnet moves away from the

main body, the Reed Switch within the Detector will be

activated.

2. When the Normal Close (N.C.) device connected to Wire Input

Termina is activated (opened). l 1

3. When the pull cord of the roller shutter connected to Wire

Input Terminal is pulled down or retracted for set distance. 2

Please refer to Jumper Switch Setting section below for

setting roller shutter cord activation distance.

The Tamper Switch will be compressed against the mounting

surface when the Detector is properly installed. The tamper

switch will be activated when the Detector is removed from the

mounting location, or when its cover is removed. When the

tamper switch is triggered, the Detector will send a signal to the

Control Panel to notify the situation.

Press the Test Button to enter Test mode for 3 minutes. Under

Test mode, the LED indicator will light up every time the Detector

is activated .

Off

Normal Operation

On (2 seconds)

- When Tamper Switch is triggered

- The Detector is activated (door opened /

wired device triggered / roller shutter

activated under low battery, tamper )

triggered, or Test mode.

BBaatttteerryy

The Detector uses 3one .6V 1/2AA lithium battery as its power

source. It also features low battery detection function to notify the

Control Panel when battery voltage is low.

When the Detector is on low battery, follow the procedure below

to change the batteries.

1. Remove the Detector from mounting location, open the cover.

2. Remove the old battery.

3. Press the learn button several times to fully discharge.

4. Insert the new batteries observing correct polarity.

5. Replace the cover and re-install the Detector at mounting

location.

The jumper switches provides setting option for Door Contact

functions. Each jumper switch has 2 pins; the jumper setting is

determined by how the jumper is installed on the pins.

The Door Contact has 5 jumper switches, marked JP1, JP3, JP5,

JP6, JP8 on the PCB board from left to right.

JP1 Test Mode –

This jumper is used to put the Door Contact into permanent Test

Mode.

ON: The Door Contact is set to Test Mode permanently. You do

not need to press the Learn/Test button to enter Test Mode

O :FF The Door Contact is set to Normal Mode. You can still press

the Learn/Test button to enter Test Mode temporarily for 3

minutes. (Factory Default)

JP3 Reed Switch –

This jumper is used to enable or disabled the Door Contact’s

Reed Switch.

ON: The Reed Switch is Disabled. The Door Contact can only be

activated by the Wire Input Terminals

O :FF The Reed Switch is Enabled. The Door Contact can be

activated by both Reed Switch and Wire Input Terminals.

(Factory Default)

JP5, JP6, JP8 Roller Shutter Pull Cord –

Activation Distance

This jumper is used to set the distance the pull cord on the roller

shutter needs to travel before the Door Contact is activated. The

distance is measured by the number of pulse signal sent to Wire

Input Terminal 2 when the pull cord is pulled or retracted. Only

one of the 3 jumpers can be turned on at a time.

JP5 ON: The Door Contact will be activated after detecting 5

pulses from roller shutter within 10 seconds.

JP6 ON: The Door Contact will be activated after detecting 6

pulses from roller shutter within 10 seconds. (Factory Default)

JP8 ON: The Door Contact will be activated after detecting 8

pulses from roller shutter within 10 seconds.

EEnnvviirroonnmmeennttaall CCoonnddiittiioonn

- C to 40 C, relative humidity 85% non-condensing 10° ° .

868 MHz FM

Jumper On

The jumper link is

inserted connecting

the two pins

Jumper Off

if the jumper link is

removed

or parked on one pin.

Produktspezifikationen

Marke:	Blaupunkt
Kategorie:	Sicherheitskamera
Modell:	DC-S3
Produktfarbe:	Weiß
Übertragungstechnik:	Kabellos
Betriebstemperatur:	-10 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 85 %
Abmessungen (BxTxH):	32 x 22 x 107 mm
Sensor-Abstand:	300 m