Black Box LES431A Bedienungsanleitung

Black Box Server LES431A

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Black Box LES431A (2 Seiten) in der Kategorie Server. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com

Page 5 Page 6

Black Box and the Double Diamond logo are registered trademarks of

BB Technologies, Inc. UL is a registered trademark of Underwriters

Laboratories. Any other trademarks mentioned in this manual are

acknowledged to be the property of the trademark owners.

Quick Start Guide

Modbus Hardened Serial Server

LES431A

Order toll-free in the U.S.:

Call 877-877-BBOX

(outside U.S. call 1-724-746-5500)

FREE technical support

24 hours a day, 7 days a week:

Call 724-746-5500 or

fax 724-746-0746

Mailing address:

Black Box Corporation

1000 Park Drive

Lawrence, PA 15055-1018

Web site: www.blackbox.com

E-mail: info@blackbox.com

Customer

Support

Information

LES431A Quick Start Guide

Step 12. Set up Port 1 ID remap.

• Only use this screen to remap “Modbus Slave IDs.”

• On each line, select the range of IDs to re-route. In

the first box, enter the first serial port of the range

to remap from. Valid port IDs range from 1 to 247.

• Second box: Enter the last serial port of the range to

remap.

• Third box: Enter starting ID of the range to remap to.

• Fourth box: Auto fills based on ranges entered in the

first three columns.

Step 13. Set up Modbus ID routing.

• Only use this screen to re-route “Modbus Slave IDs.”

• On each line, select the range of IDs to re-route. In

the first box enter the starting ID. Valid IDs range

from 1 to 247.

• Second box: Enter the last ID of the range to

re-route.

• Third box: Enter the “IP Address” or “Port” that has

slave devices attached.

• Fourth box: Shows the IP address of the slave device,

if an IP address is chosen in the third box.

Step 14. Set up Modbus priority.

• Only use this screen to set “Modbus Priority.”

• Enter up to five different priorities, based on

“Originating IP Address,” “Modbus ID,” “Modbus

Function Code,” or a combination of these.

• “IP Address” sets a static IP address for the Modbus

Hardened Serial Server.

• “Modbus ID” has a valid range from 1 to 247.

• Function code has a valid range from 1 to 99.

Step 15. Save and logout.

• If you have completed the configuration, click

“Save” to save the configuration to the serial server.

• To logout, click the “Logout” button.

Step 1. Check for all required hardware.

Your package includes:

• 1-Port Modbus Hardened Serial Server

• CD-ROM containing software

• This Quick Start Guide

You will also need:

• Network and serial cables (not included)

• Power supply (not included)

Step 2: Install the hardware.

• Connect a 10- to 48-VDC (58 VDC max.)

power supply (4.0 W required).

• Connect the network cable from the serial

server to a network drop using a standard

serial cable.

• Connect the serial device to the RS-232

DB9 or terminal block serial connector with a

straight-through cable for a DCE device or a

null-modem cable for a DTE device.

NOTE: UL® requires one conductor per terminal,

28 to 16 AWG copper-wire, tightening

torque of 5 kg-cm, and 105° C rating

sized for 60° C ampacity.

LES431A Quick Start Guide, rev. 1

LES431A Quick Start Guide

Step 16. Test and verify operation.

• The primary check for normal operation is the device

LEDs. See Step 3 in this document for more

information.

• For advanced information, see the “Modbus

Configuration Manager” menu, at the top of the

Modbus Hardened Serial Server Manager screen.

• Select “Diagnostic” to check communications status

with the Modbus Hardened Serial Server, then select

the device for which you want to check

communications data.

• A report of reply times and ping statistics is

generated and can be saved.

• Select “Monitor” to review activity logs of attached

LES431A devices, then select the device for which

logged information is needed.

• Logged information includes “Time,” “Source and

Destination,” “Type of event,” “Subscriber ID,”

“Data collected,” and “Information” the Modbus

Hardened Serial Server software has gathered since

the current login of the affected device.

724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com

LES431A Quick Start Guide LES431A Quick Start GuideLES431A Quick Start Guide

Page 3Page 2 Page 4

Step 5. Install Black Box Modbus Hardened Serial

Server software.

• Insert the included CD and it should autostart.

• Follow the prompts to install the software.

NOTE: Make sure you have administrative rights and

disable firewalls.

Step 6. Set up Black Box Modbus Hardened Serial

Server software.

• Open the software. Click ”Start—>Programs—>

Black Box—> Modbus Hardened Serial Server

Software.” The “Discovery” page opens.

NOTE: If the device does not connect, cycle (unplug

then replug) the power, then try again to

connect.

• To configure via the network, select “Network.”

• If you know the IP address, select “The device is at

this address” and type in the address. If not, select

“I don’t know the IP address of the device.”

• Click “Connect.”

Step 6. Set up the Web interface.

• Open a browser and type the IP address of the serial

server into the address bar.

• When the Modbus Hardened Serial Server is found,

the “Login” window appears.

Step 7. Login.

• Click “Login.” (The password is blank from the

factory.)

• The “Configuration/General” page appears.

Step 8. Set up the network.

• “I want DHCP” is pre-selected to set up the network

using dynamic IP addressing. The Modbus Hardened

Serial Server is set up at the factory to receive an IP

assignment from a DHCP server. If a DHCP server is

not available on your network, it will default to

. 169.254.102.39

• If this address does not work with your PC, change

your network settings to:

- IP Address = 169.254.102.1

- Subnet Mask = 255.255.255.0

- Default Gateway = 169.254.102.100

• If you need to use different settings, refer to the

user’s manual for instructions.

Step 9. Set up Modbus TCP.

Modbus TCP settings:

• “Connect to Port” identifies the TCP port used in

TCP client mode. Valid range is 1 to 65535.

• “Response Timeout” is the maximum response time.

Valid range is 1 to 65535.

TCP Server Settings:

• “Listen on port” identifies a TCP port in TCP server

mode.

• “Limit the number of connections” controls the

number of simultaneous TCP clients that can be

connected.

• “Allow everyone,” “allow specific IP address,” and

“allow a range of IP addresses” are Connection Filter

mode options that control which TCP clients can

connect.

Step 10. Set up Port 1 Serial.

• Change the “Description” of the serial port if

needed.

• Select the “Mode” to RS-232, RS-422, RS-485

2-wire, or RS-485 4-wire.

• Select the baud rate, data bits, stop bits, parity, and

flow control needed to communicate with the serial

device.

Step 11. Set up Port 1 Modbus.

• Select the “Attached” as “Master” or “Slave.”

• Select the Modbus protocol to be used, either RTU

or ASCII.

• As needed, check option boxes for “Enable Modbus

broadcast,” “Enable OBh Exception,” and “Enable

serial message buffering.”

• Select from 0 to 5 “Modbus Serial Retries.”

• Enter “Milliseconds Modbus Message Timeout,”

from 1 to 65535.

• Enter “Milliseconds TX Delay,” from 1 to 65535.

Step 3: LED status.

LED Status

Ready Blinks if system is operating correctly.

Port 1 ON when port is open; blinks when data present on serial port.

Link ON when device is operating in 100BASE-TX mode. Blinks

when data is present on the Ethernet link.

Step 4: Mode switch.

Hold in Mode switch for… Result

0 to 2 seconds Initiates a hardware reset.

2 to 10 seconds Enters Console mode.

More than 10 seconds Resets to factory defaults.

Produktspezifikationen

Marke:	Black Box
Kategorie:	Server
Modell:	LES431A
Gewicht:	100 g
Produktfarbe:	Schwarz
Internationale Schutzart (IP-Code):	IP30
Betriebstemperatur:	-40 - 80 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 95 %
Netzstandard:	IEEE 802.3
Unterstützte Netzwerkprotokolle:	TCP, IPv4, UDP, ARP, HTTP 1.0, ICMP/PING, DHCP/BOOTP, DHCP, , TCP
Zertifizierung:	FCC Part 15, Class A, CE, NEMA TS2, UL Class 1, Division 2, Groups A, B, C, D
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-40 - 85 °C
Energieverbrauch:	4000 mA
Unterstützt Windows-Betriebssysteme:	Windows 7, Windows Vista, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64
Auto MDI/MDI-X:	Ja
Abmessungen (BxTxH):	81 x 119 x 30 mm
Serielle Schnittstelle:	RS-232/422/485
Eingangsspannung:	10 - 58 V
Verkabelungstechnologie:	10/100Base-T(X)
Anzahl serielle Anschlüsse:	1
Unterstützung Datenflusssteuerung:	Ja
Datenübertragungsrate:	0.234 Mbit/s
Unterstützte Server-Betriebssysteme:	Windows Server 2003, Windows Server 2008
Baudrate:	230400 Kbit/s
Datenbits:	5, 6,7, 8
Stop bits:	1, 1.5, 2
RS-232 Signale:	CTS, DCD, DSR, DTR, GND, RTS, RXD, TXD
RS-485 signale:	Data+, Data-, GND
RS-422 signale:	GND