Black And Decker HPD1402 Bedienungsanleitung

Black And Decker bohren HPD1402

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Black And Decker HPD1402 (6 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

•Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tools operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

Service

•Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock or injury.

Specific Safety Rules

•Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

•When working on a ladder or on scaffolding be sure to lay the tool down on its side

when not in use. Some tools with large battery packs will stand upright but may be easily

knocked over.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber. (CCA)

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min ........................minutes ......................alternating current

......................direct current no ........................no load speed

..........................Class II Construction ........................earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations

per minute

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the battery is out of the

tool or charger. Remove cap before placing battery in charger or

tool.

WARNING: Do not store or carry battery so that metal objects can contact exposed

battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product

kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap. Transporting

batteries can possibly cause fires if the battery terminals inadvertently come in contact with

conductive materials such as keys, coins, hand tools and the like. The US Department of

Transportation Hazardous Material Regulations (HMR) actually prohibit transporting

batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage)

UNLESS they are properly protected from short circuits. So when transporting individual

batteries, make sure that the battery terminals are protected and well insulated from

materials that could contact them and cause a short circuit."

General Safety Rules

WARNING: Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

•Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes. Use in well ventilated areas only.

•Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

•Double insulated tools are equipped with a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit

fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician

to install a polarized outlet. Do not change the plug in any way. Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply

system.

•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

•Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

•When operating a power tool outside, use an outdoor extension cord marked "W-A"

or "W." These cords are rated for outdoor use and reduce the risk of electric shock.

Personal Safety

•Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in serious

personal injury.

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair

can be caught in moving parts. Air vents cover moving parts and should be avoided.

•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is

left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

•Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

•Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventative safety measures reduce

the risk of starting the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE

REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

Catalog No. HPD1402, HPD1802

Cat. # HPD1402, HPD1802 Form # 497158-33

Trigger Switch

Interrupteur à détente

Gatillo interruptor

Depress for reverse (this side)

Enfoncer pour la marche arrière

Oprima para marcha hacia adelante

Depress for forward (other

side)

Enfoncer pour la marche avant

Oprima para reversa

Screw Icon

Symbole d’une vis

Icono de tornillo

Drill Bit Icon

Symbole d’une mèche de

perceuse

Icono de broca

Torque Adjust Collar

collier de réglage du couple

collarÍn de ajuste de par (torque)

Gear Shifter

Sélecteur de vitesses

Palanca de cambio de

engranes

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO (544-6986)

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986)

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., AND

DATE CODE (e.g. 20000130M). IN MOST CASES, A REPRESENTATIVE CANBLACK & DECKER

RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT, GIVE

US A CALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.

Battery Cap

Important Safety Instructions

•SAVE THESE INSTRUCTIONS.

• Before using charger, read and understand all instructions and cautionary markings on

(1) charger, (2) battery pack, and (3) product using battery pack.

DANGER: 120 volts present at charging terminals. Do not probe with conductive objects.

Danger of electric shock or electrocution.

DANGER: If battery pack case is cracked or damaged, do not insert into charger. Danger

of electric shock or electrocution.

DANGER: Never attempt to open the battery pack for any reason. If the plastic housing

of the battery pack breaks or cracks, return to a service center for recycling.

WARNING: Don’t allow any liquid to get inside charger. Electric shock may result.

CAUTION: To reduce risk of injury, charge only Black & Decker rechargeable batteries.

Other types of batteries may burst, causing personal injury and damage.

• To facilitate the cooling of the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

• Do not expose charger to rain or snow.

• Use of an attachment not recommended or sold by Black & Decker may result in risk of

fire, electric shock, or injury to persons.

• This charger is not intended for any uses other than charging Black & Decker recharge-

able batteries. Any other uses may result in risk of fire, electric shock or electrocution.

• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

• Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

• An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock, or electrocution. If an extension

cord must be used, make sure:

• That the pins on plug of extension cord are the same number, size and shape of

those of plug on charger.

• That extension cord is properly wired and in good electrical condition and the wire

size is large enough for AC ampere rating of charger as specified below.

An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable,

that is, 16 gauge has more capacity than 18 gauge. When using more than one extension

to make up the total length, be sure each individual extension contains at least the

minimum wire size.

RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS

Total Extension Cord Length (feet)

25 50 75 100 125 150 175

Wire Gauge

18 18 16 16 14 14 12

• The charger is ventilated through slots in the housing. Do not place any object on top of

charger or place the charger on a soft surface that might block the ventilation slots and

result in excessive internal heat. Place the charger in a position away from any heat

source.

• Do not operate charger with damaged cord or plug — have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service or repair

is required. Incorrect reassembly may result in risk of electric shock, electrocution or fire.

• The charger is designed to operate on standard120 VAC, 60Hz household electrical

power. Do not attempt to use it on any other voltage.

• To reduce risk of electric shock, unplug charger from outlet before attempting any

cleaning. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• DO NOT store or use the tool and battery pack in locations where the temperature may

reach or exceed 105°F (such as outside sheds or metal buildings in summer).

• A small leakage of liquid from the battery cells may occur under extreme usage,

charging or temperature conditions. This does not indicate a failure. However, if the

outer seal is broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10

minutes and seek immediate medical attention. The liquid is a MEDICAL NOTE:

25-35% solution of potassium hydroxide.

SAVE THESE INSTRUCTIONS

Introduction

READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS MANUAL BEFORE

ATTEMPTING TO CHARGE THE BATTERY PACK FOR YOUR TOOL.

Your charger is designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any

other voltage. Charge time is 3 to 6 hours depending on battery pack type and condition.

Charging Procedure

1. Plug the charger into an appropriate outlet.

2. Insert 1 or 2 batteries into the charger (Figure 1).

NOTE: Charge time is the same for multiple batteries. Be sure the battery is fully seat-

ed in the charger. The red “Charging Indicator” light will come on indicating that there

is contact between the battery and charger. The light will stay on as long as the battery

is in the charger and the charger is plugged into a working outlet. It WILL NOT flash,

go out or change to a different color when the charging cycle is complete.

Remove pack from the charger and place in tool. To remove the battery fromNOTE:

the tool, press down on the release button on the back of the battery (Figure 2) and

pull out.

Leaving the Battery Pack in the Charger

The charger and battery pack can be left connected with the red light glowing indefinitely.

The charger will keep the battery pack fresh and fully charged.

NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery

pack has not been kept on maintenance charge, it may need to be recharged before use. A

battery pack may also slowly lose its charge if left in a charger that is not plugged into an

appropriate AC source.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when

the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery

pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is

important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a

normal condition, and does not indicate a problem.

3. If the battery pack does not charge properly — (1) Check power at receptacle by plug-

ging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light

switch which turns power off when you turn out the lights. (3) Move charger and battery

pack to a location where the surrounding air temperature is approximately 65°F - 75°F

(18°- 24°C). (4) If charging problems persist, take or send the tool, battery pack and

charger to your local service center.

4. The battery pack should be recharged when it does not produce sufficient power on

jobs which were easily done previously. DO NOT CONTINUE use under these condi-

tions. Follow the charging procedures. You may also charge a partially used pack when-

ever you desire with no adverse affect on the battery pack.

5. Black & Decker battery packs that are labeled “NiMH” should only be used with charg-

ers labeled “NiMH“ or “NiCd/NiMH.”

6. Under certain conditions, with the charger plugged into the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or

any buildup of metallic particles should be kept away from charger cavities. Always

unplug the charger from the power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

7. Do not immerse charger in water or any other liquid.

Operating Instructions

TRIGGER SWITCH & REVERSING BUTTON - FIGURE 3

The drill is turned ON and OFF by pulling and releasing the trigger switch shown in Figure

3. The farther the trigger is depressed, the higher the speed of the drill. A forward/reverse

control button determines the direction of the tool and also serves as a lock off button. To

select forward rotation, release the trigger switch and depress the forward/reverse control

button. To select reverse, depress the forward/reverse control button the opposite direction.

The center position of the control button locks the tool in the off position. When changing

the position of the control button, be sure the trigger is released.

TORQUE CONTROL - FIGURE 4

To set the tool’s torque, rotate the adjustable torque collar as required. There are 36 clutch

settings in all. These are indicated by screw icons depicted on the torque collar. For light

duty work when using small screws, set the collar to the smallest screw icon. Each click in a

clockwise direction means an increase in the torque produced. The highest position is the

drill mode and is indicated by a drill bit icon. In this position the clutch will not operate. This

permits heavy duty drilling.

DUAL RANGE GEARING - FIGURE 5

The dual range feature of your drill allows you to shift gears for greater versatility. To select

low speed, high torque setting (position 1), turn tool off and permit to stop. Push button

forward towards the chuck. To select the high speed, low torque setting (position 2), turn

tool off and permit to stop. Slide gear shifter back (away from chuck). NOTE: Do not

change gears when tool is running. If you are having trouble changing gears, make sure

that the dual range gear button is either completely pushed forward or completely pushed

back.

KEYLESS CHUCK

To insert a drill bit or other accessory:

1. Grasp the rear half of the chuck with one hand and use your other hand to rotate

the front half in the counterclockwise direction, as viewed from the chuck end.

2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding

the rear half of the chuck and rotating the front portion in the clockwise direction as

viewed from the chuck end.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the

front part of the chuck and turning the tool on. Damage to the chuck and personal injury

may occur when changing accessories.

REMOVABLE CHUCK WITH QUICK CONNECT TM BIT CHANGE SYSTEM- FIGURE 6

Another unique feature of your drill is the ability to remove the chuck quickly and easily.

This allows for a drill bit to be in the keyless chuck, while another accessory such as a

screwdriver bit, can be inserted into the Quick ConnectTM hex shaft at the same time.

To remove the chuck:

1. Grasp the drill and depress the two orange buttons on the chuck collar as shown in

Figure 6.

2. With the buttons depressed, pull straight out.

To replace the chuck:

1. Push the quick connect chuck straight on with a slight twisting motion until you hear

it click into place.

To insert a screwdriver bit into the Quick ConnectTM hex shaft, push the bit in until you hear

it click into place. To remove the bit, hold the drill as shown in figure 7. Push in evenly on

the spring loaded disc with two fingers and pull the bit straight out.

SCREW DRIVING

For driving fasteners, the reversing button should be pushed to the left. Use reverse (button

pushed to the right) for removing fasteners. When moving from forward to reverse, or vice

versa, always release the trigger switch first.

ON BOARD BIT STORAGE

A bit storage slot is built-in to the area just above the battery.

DRILLING

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the Safety Instructions.

• Secure and maintain work area, as instructed in the Safety Instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the

drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

but not so much as to stall the motor or deflect the bit.

• Hold the drill firmly with two hands to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the

last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce

jamming.

• Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which

should be drilled dry. The lubricants that work best are sulphurised cutting oil or lard oil.

• When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out

frequently to clear chips from the flutes.

•Make sure switch turns drill on and off.

WARNING: It is important to support the work properly and to hold the drill firmly to

prevent loss of control which could cause personal injury. If you have any questions on how

to properly operate tool, call: 1-800-54-HOW-TO (544-6986).

DRILLING IN WOOD

Holes in wood can be made with the same twist drill bits used for metal or with spade bits.

These bits should be sharp and should be pulled out frequently when drilling to clear chips

from the flutes.

DRILLING IN METAL

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which

should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard

oil.

DRILLING IN MASONRY

Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but

not so much that you crack the brittle material. A smooth, even flow of dust indicates the

proper drilling rate.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

An occasional application of a household oil to the Quick Connect

TM hex shaft will help

prevent rust.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service organizations, always using identical replacement

parts.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to

recycle the battery (or battery pack) at the end of its useful life have already been

paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium

batteries in the trash or municipal solid waste stream and the RBRC program

provides an environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent nickel-

cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service center

or to your local retailer for

recycling. You may also contact your local recycling center for information on where to drop

off the spent battery, or call 1-800-8-BATTERY.

Accessories

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-54-HOW-TO (544-6986).

WARNING: The use of any accessory not recommended for use with this tool could

be hazardous.

CONSERVER CES MESURES.

ZONE DE TRAVAIL

• S’assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et

des endroits sombres présentent des risques d’accidents.

• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme

celles dégagées par des liquides, des gaz ou des poussières inflammables).

Lesétincelles générées par le moteur des outils électriques peuvent enflammer les

poussières ou les vapeurs.

• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu’on utilise

un outil électrique. Une distraction peut entraîner la perte de maîtrise de l’outil.

MESURES DE SÉCURITÉ RELATIVES À L’ÉLECTRICITÉ

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter

l’outil ni tirer sur le cordon pour débrancher l’outil. Éloigner le cordon des sources

de chaleur, des flaques d’huile, des arêtes tranchantes et des pièces mobiles.

Remplacer immédiatement les cordons endommagés. Les cordons endommagés

augmentent les risques de secousses électriques.

• Il faut charger un outil à piles intégrées ou un ensemble de piles seulement dans le

chargeur conçu à cet effet. Un chargeur convenant pour un type de piles peut présenter

un risque d’incendie lorsqu’on s’en sert avec un autre type de piles.

• Utiliser un outil alimenté par piles seulement avec la pile appropriée. L’utilisation de

toute autre pile présente des risques d’incendie.

SÉCURITÉ PERSONNELLE

• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu’on utilise un outil

électrique. Ne pas s’en servir lorsqu’on est fatigué ou affaibli par des drogues, de

l’alcool ou des médicaments. De graves blessures peuvent résulter d’un moment

d’inattention lors de l’utilisation d’un outil électrique.

•Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des

bijoux. Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les

vêtements et les gants des pièces en mouvement qui peuvent les happer.

•Éviter les démarrages accidentels. S’assurer que l’interrupteur est en position hors

tension avant d’insérer la pile. Afin d’éviter les risques de blessures, ne pas transporter

l’outil avec le doigt sur l’interrupteur ni insérer la pile dans un outil dont l’interrupteur est en

position sous tension.

•Enlever les clés de réglage avant de mettre l’outil sous tension. Une clé qui est laissée

sur une pièce rotative de l’outil présente des risques de blessures.

•Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s’assure d’une

meilleure maîtrise de l’outil dans des situations imprévues grâce à une position stable et un

bon équilibre.

•Porter de l’équipement de sécurité. Toujours porter des lunettes de sécurité. Dans

certaines conditions, il faut porter des masques respiratoires, des chaussures

antidérapantes, un casque de sécurité ou des protège-tympans.

UTILISATION ET ENTRETIEN DE L’OUTIL

•Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de

soutenir la pièce à ouvrer sur une plate-forme stable. La pièce est instable lorsqu’elle

est retenue par la main ou le corps de l’utilisateur. Cela présente des risques de perte de

maîtrise de l’outil.

•Ne pas forcer l’outil. Utiliser l’outil approprié à la tâche. L’outil approprié fonctionne

mieux et sûrement lorsqu’on s’en sert à son rendement nominal.

•Ne pas se servir de l’outil lorsque l’interrupteur est défectueux. Le cas échéant, l’outil

est dangereux et il faut le réparer.

•Enlever la pile de l’outil ou placer celui-ci en position hors tension avant de le régler,

d’en remplacer les accessoires ou de le ranger. On minimise de la sorte le risque de

démarrage accidentel de l’outil.

•Ranger l’outil hors de portée des enfants et de toute autre personne qui n’en connaît

pas le fonctionnement. L’outil est dangereux entre les mains de ces personnes.

•Lorsque la pile ne sert pas, l’éloigner de tout objet métallique (comme des

trombones, des pièces de monnaie, des clés, des clous, des vis ou tout autre petit

objets métalliques qui peut créer une connexion d’une borne à l’autre). Lorsque les

bornes sont court-circuitées, cela peut générer des étincelles, des brûlures ou un incendie.

•Prendre soin des outils. S’assurer que les outils de coupe sont tranchants et

propres. Des outils bien entretenus à arêtes tranchantes ont moins tendance à se coincer

et ils se maîtrisent mieux.

•Vérifier l’alignement et les attaches des pièces mobiles, le degré d’usure des pièces

ainsi que tout autre facteur susceptible de nuire au bon fonctionnement de l’outil.

Faire réparer un outil endommagé avant de s’en servir. Des outils mal entretenus sont

la cause de nombreux accidents.

•Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires qui

conviennent à un outil peuvent présenter des risques avec un autre outil.

ENTRETIEN

•Confier l’entretien de l’outil seulement à du personnel qualifié. Le non-respect de la

présente directive présente des risques de blessures.

•Lors de l’entretien de l’outil, utiliser seulement des pièces de rechange identiques.

Respecter les consignes relatives à l’entretien du présent guide d’utilisation. Il y a

risque de secousses électriques ou de blessures lorsqu’on utilise des pièces non autorisées

ou lorsqu’on ne respecte pas les consignes relatives à l’entretien

MESURES DE SÉCURITÉ SPÉCIFIQUES

• Saisir l’outil par ses surfaces de prises isolées lorsque l’outil peut entrer en contact

avec des fils cachés. En cas de contact avec un fil sous tension, les pièces métalliques

de l’outil seront sous tension et l’utilisateur subira des secousses électriques.

•Lorsqu’on est installé sur une échelle ou un échafaudage pour travailler, on doit

déposer l’outil sur le côté lorsqu’on ne s’en sert plus. Bien que certains outils munis

d’un gros bloc-piles puissent être placés à la verticale, dans cette position, ils peuvent

facilement être renversés.

L’étiquette de l’outil peut comporter les symboles suivants.

V ....................................volts A..........................ampères

Hz ..................................hertz W ........................watts

min..................................minutes ......................courant alternatif

................................courant continu no ........................sous vide

....................................Construction de classe II ........................borne de mise à la

minute

..................................symbole d´avertissement .../min ..................tours ou courses

à la minute

CONSERVER CES MESURES.

INFORMATION CONCERNANT LE CAPUCHON DU BLOC-PILE

Un capuchon est fourni avec le bloc-pile en vue d’être utilisé chaque fois qu’on retire ce

dernier de l’outil ou du chargeur en vue de le ranger ou de le transporter; enlever le

capuchon avant de remettre le bloc-pile dans le chargeur ou dans l’outil.

AVERTISSEMENT : s’assurer, au moment de ranger ou de transporter le bloc-pile,

qu’aucun objet métallique n’entre en contact avec les bornes à découvert du bloc-pile. Par

exemple, il faut éviter de placer un bloc-pile sans capuchon dans un tablier, une poche,

une boîte à outils ou un tiroir (etc.) contenant des objets tels que des clous, des vis ou des

clés, car le bloc-pile pourrait causer un court-circuit et s’endommager, ou risquer de provo-

quer des brûlures ou un incendie.

Mesures de sécurité importantes

•CONSERVEZ CES DIRECTIVES.

• Bien lire toutes les directives et tous les avertissements qui se trouvent sur (1) le

chargeur, (2) l’ensemble de piles et (3) l’outil avant d’utiliser le chargeur.

DANGER : Les bornes du chargeur sont sous une tension de 120 volts. Ne pas les

examiner avec un objet conducteur; cela présente des risques de secousses électriques.

DANGER : Ne pas placer dans le chargeur un ensemble de piles craqué ou endommagé;

cela présente des risques de secousses électriques.

MISE EN GARDE : Ne jamais tenter d’ouvrir un ensemble de piles. Lorsque le boîtier en

plastique craque ou se casse, en confier le recyclage à un centre de service.

AVERTISSEMENT : Ne laisser aucun liquide s’infiltrer dans le chargeur car cela

représente des risques de secousses électriques.

MISE EN GARDE : Afin de réduire les risques de blessures, charger seulement des piles

rechargeables Black & Decker. Tout autre type de piles peut exploser; ce qui présente des

risques de blessures et de dommages.

• Pour faciliter le refroidissement de l’ensemble de piles après s’en être servi, éviter de

placer le chargeur ou l’ensemble de piles dans un endroit chaud comme une remise en

métal ou une remorque non isolée.

• Protéger le chargeur de la pluie ou de la neige.

• L’utilisation d’un accessoire non recommandé ni vendu par comporte desBlack & Decker

risques d’incendie, de secousses électriques ou de blessures.

• L’utilisation du chargeur pour tout ensemble de piles autres que les ensembles

rechargeables Black & Decker comporte des risques d’incendie et de secousses électriques.

• Pour minimiser les risques de dommages au cordon et à sa fiche, débrancher l’appareil

en tirant sur la fiche plutôt que sur le cordon.

• Placer le cordon de sorte qu’on ne puisse pas marcher ni s’accrocher dessus et qu’il ne

soit pas autrement sujet aux dommages et aux contraintes.

• Ne pas utiliser de rallonge à moins que cela ne soit absolument nécessaire, car l’usage

d’une rallonge ayant une puissance inadéquate pourrait causer des risques d’incendie,

de choc électrique ou d’électrocution. Si une rallonge est nécessaire, s’assurer que :

• les broches de la prise de la rallonge sont de mêmes nombre, taille et forme que celles

de la prise du chargeur.

• la rallonge est correctement câblée et en bonne condition, et que le calibre du fil est

suffisant pour l’intensité nominale de courant alternatif du chargeur comme spécifié

ci-dessous.

Pour la sécurité de l’utilisateur, utiliser une rallonge du calibre AWG approprié. Plus le

calibre est petit, plus la capacité est grande; autrement dit, une rallonge de calibre 16 est

plus puissante qu’une rallonge de calibre 18. Lorsqu’on utilise plusieurs rallonges pour

obtenir la longueur voulue, s’assurer que chacune d’elles présente les valeurs minimales

requises. CALIBRE MINIMAL (AWG) RECOMMANDE DES RALLONGES

LONGUEUR TOTALE DE LA RALLONGE (EN METRES)

7,6 15,2 22,8 30,4 38,1 45,7 53,3

CALIBRE AWG 18 18 16 16 14 14 12

• La ventilation du chargeur se fait par les fentes sur le dessus et le dessous de l’appareil.

Ne rien déposer sur le chargeur et ne pas déposer ce dernier sur une surface qui

pourrait en bloquer les orifices car cela risque de provoquer la surchauffe de l’appareil.

Éloigner le chargeur des sources de chaleur.

• Ne jamais se servir d’un chargeur dont le cordon ou la fiche sont endommagés. Les

remplacer immédiatement.

• Ne jamais se servir d’un chargeur qui a encaissé un coup brusque, qui est tombé ou qui

est endommagé. Le faire vérifier à un centre de service autorisé.

• Ne jamais démonter le chargeur. N’en confier la réparation ou l’entretien qu’à un centre

de service autorisé. Le remontage non conforme du produit comporte des risques

d’incendie ou de secousses électriques.

IMPORTANTES MESURES DE SÉCURITÉ - POUR TOUS LES OUTILS

ALIMENTÉS PAR PILES

AVERTISSEMENT! Lire et comprendre toutes les directives. Le non-respect de toutes

les directives suivantes présente des risques de secousses électriques, d’incendie ou

de blessures graves.

AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA

RAISON PRIÈRE DE COMPOSER

1 800 544-6986

The following accessories should be used only in the sizes specified below:

BITS, METAL DRILLING – Up to 3/8" (9.5mm); BITS, MASONRY DRILLING – Up to 3/8"

(9.5mm); WOOD DRILLING – Up to 1/2" (12.7mm).

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide

customers with efficient and reliable power tool service. Whether you need technical

advice, repair, or genuine factory replacement parts, contact the Black & Decker location

nearest you. To find your local service location, refer to the yellow page directory under

"Tools—Electric" or call:

1-800-54-HOW TO. (544-6986)

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge

in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may

be required. Black & Decker owned and authorized Service Centers are listed under

"Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center.

This product is not intended for commercial use.

Free Warning Label Replacement: If your warning labels become illegible or are

missing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

Capuchon du bloc-pile

Produktspezifikationen

Marke:	Black And Decker
Kategorie:	bohren
Modell:	HPD1402

Brauchst du Hilfe?

Wenn Sie Hilfe mit Black And Decker HPD1402 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung bohren Black And Decker

Black And Decker GC1800 Bedienungsanleitung

13 Oktober 2024

Black And Decker KD664 Bedienungsanleitung

4 Oktober 2024

Black And Decker XD1200 Bedienungsanleitung

4 Oktober 2024

Black And Decker HD455KA Bedienungsanleitung

29 September 2024

Black And Decker PS3500 Bedienungsanleitung

21 September 2024

Black And Decker FSD962 Bedienungsanleitung

20 September 2024

Black And Decker FS7000D Bedienungsanleitung

17 September 2024

Black And Decker CD18SR Bedienungsanleitung

15 September 2024

Black And Decker HP1800 Bedienungsanleitung

14 September 2024

Black And Decker CD96C Bedienungsanleitung

13 September 2024

Bedienungsanleitung bohren

Neueste Bedienungsanleitung für -Kategorien-

Ozito BDP-500 Bedienungsanleitung

16 Oktober 2024

MSW -DDM255 Bedienungsanleitung

16 Oktober 2024

MSW -DDM152 Bedienungsanleitung

16 Oktober 2024

MSW -DDM205 Bedienungsanleitung

16 Oktober 2024

MSW -DDM230 Bedienungsanleitung

16 Oktober 2024

Einhell BM-G1100 E Bedienungsanleitung

15 Oktober 2024

Sun Joe 24V-DDK-LTX-PNK Bedienungsanleitung

15 Oktober 2024

Makita DHR263ZJ Bedienungsanleitung

13 Oktober 2024

Rupes BH 252R Bedienungsanleitung

13 Oktober 2024

Einhell RT-RH 20/1 Bedienungsanleitung

13 Oktober 2024