Black And Decker HPD1400 Bedienungsanleitung

Black And Decker bohren HPD1400

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Black And Decker HPD1400 (7 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/7

GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS

WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all

instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust

or fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from

heat, oil, sharp edges or moving parts. Replace damaged cords immediately.

Damaged cords may create a fire.

• A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery. A charger that may be

suitable for one type of battery may create a risk of fire when used with another battery.

• Use battery operated tool only with specifically designated battery pack. Use of any

other batteries may create a risk of fire.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in serious

personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing , and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts. Air vents cover moving parts and should be avoided.

• Avoid accidental starting. Be sure switch is in the locked or off position before

inserting battery pack. Carrying tools with your finger on the switch or inserting the

battery pack into a tool with the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tool. Such

preventative safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

• When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws or other small metal objects that can make a

connection from one terminal to another. Shorting the battery terminals together may

cause sparks, burns, or a fire.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edge are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may create a risk of injury when used on

another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel may result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of shock or injury.

SPECIFIC SAFETY RULES

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord.

Contact with a “live”

wire will make exposed metal parts of the tool “live” and shock the operator.

• Wear ear protectors with impact drills.

Exposure to noise can cause hearing loss.

• Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

• Use clamps or other practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body is unstable and may lead to loss of

control.

• When working on a ladder or on scaffolding be sure to lay the tool down on its side

when not in use. Some tools with large battery packs will stand upright but may be easily

knocked over.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face and body.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation

which, if not avoided, may result in property damage.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min ........................minutes ......................alternating current

......................direct current no ........................no load speed

..........................Class II Construction

........................

earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations per

minute

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the battery is out of the

tool or charger. Remove cap before placing battery in charger or tool.

WARNING: Do not store or carry battery so that metal objects can contact exposed

battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product

kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap.

Transporting batteries can possibly cause fires if the battery terminals inadvertently come

in contact with conductive materials such as keys, coins, hand tools and the like. The US

Department of Transportation Hazardous Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon

luggage) UNLESS they are properly protected from short circuits. So when transporting

individual batteries, make sure that the battery terminals are protected and well insulated

from materials that could contact them and cause a short circuit.

INSTRUCTION MANUAL

Cat. Nos.

HPD1400,

HPD1800

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTESADVERTENCIA:

DE USAR EL PRODUCTO.

Trigger Switch

Interrupteur à détente

Gatillo interruptor

Depress for reverse

(this side)

Enfoncer pour la marche arrière

Oprima para marcha hacia adelante

Depress for forward (other side)

Enfoncer pour la marche avant

Oprima para reversa

Torque Adjust Collar

collier de réglage du couple

collarÍn de ajuste de par (torque)

Battery Cap

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE

A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.

THANK

HANK YOU

YOU FOR

FOR CHOOSING

CHOOSING B

BLACK

LACK &

DECKER

ECKER !

OWWW

WWW.B

.BLACKAND

LACKAND D

DECKER

ECKER .

.COM

COM /N

/NEW

EW O

OWNER

WNER

OREGISTER

YOUR NEW

NEW PRODUCT

PRODUCT.

button. To select reverse, depress the forward/reverse control button the opposite direction.

The center position of the control button locks the tool in the off position. When changing

the position of the control button, be sure the trigger is released.

TORQUE CONTROL - FIGURE 4

To set the tool’s torque, rotate the adjustable torque collar as required. There are 32 clutch

settings in all. These are indicated by numbers depicted on the torque collar. For light duty

work when using small screws, set the collar to the smallest number. Each click in a

clockwise direction means an increase in the torque produced. If the clutch slips on the

lightest setting, turn the clutch collar to a higher number. The highest position is the drill

mode and is indicated by a drill bit icon. In this position the clutch will not operate. This

permits heavy duty drilling.

DUAL RANGE GEARING - FIGURE 5

The dual range feature of your drill allows you to shift gears for greater versatility. To select

position 1, turn tool off and permit to stop. Slide gear shifter back (away from chuck).

Position 1 is for driving and removing screws and drilling with bits that require high torque.

To select position 2, turn tool off and permit to stop. Push button forward towards the chuck.

Position 2 is for drilling using smaller bits. NOTE: Do not change gears when tool is running.

If you are having trouble changing gears, make sure that the dual range gear button is

either completely pushed forward or completely pushed back.

KEYLESS CHUCK

To insert a drill bit or other accessory:

Loosen the chuck by rotating the sleeve counterclockwise. Insert the bit or other accessory

fully into the chuck, and tighten securely by rotating in the clockwise direction as viewed

from the chuck end.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the

front part of the chuck and turning the tool on. Damage to the chuck and personal injury

may occur when changing accessories.

SCREW DRIVING

For driving fasteners, the reversing button should be pushed to the left. Use reverse (button

pushed to the right) for removing fasteners. When moving from forward to reverse, or vice

versa, always release the trigger switch first.

DRILLING

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the Safety Instructions.

• Secure and maintain work area, as instructed in the Safety Instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the

drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but

not so much as to stall the motor or deflect the bit.

• Hold the drill firmly with two hands to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last

part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce

jamming.

• Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which

should be drilled dry. The lubricants that work best are sulphurized cutting oil or lard oil.

• When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out

frequently to clear chips from the flutes.

•Make sure switch turns drill on and off.

WARNING: It is important to support the work properly and to hold the drill firmly to

prevent loss of control which could cause personal injury. If you have any questions on how

to properly operate tool, call: 1-800-54-HOW-TO (544-6986).

DRILLING IN WOOD

Holes in wood can be made with the same twist drill bits used for metal or with spade bits.

These bits should be sharp and should be pulled out frequently when drilling to clear chips

from the flutes.

DRILLING IN METAL

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which

should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard

oil.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service organizations, always using identical replacement

parts.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to

recycle the battery (or battery pack) at the end of its useful life have already been paid by

Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the

trash or municipal solid waste stream and the RBRC program provides an environmentally

conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent nickel-

cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service center

or to your local retailer for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery, or call 1-800-8-BATTERY.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1 800 544-6986.

WARNING: The use of any accessory not recommended for use with this tool could

be hazardous.

The following accessories should be used only in the sizes specified below:

BITS, METAL DRILLING – Up to 3/8" (9.5mm); BITS, MASONRY DRILLING – Up to 3/8"

(9.5mm); WOOD DRILLING – Up to 1/2" (12.7mm).

IMPORTANT SAFETY INSTRUCTIONS

•SAVE THESE INSTRUCTIONS.

• Before using charger, read and understand all instructions and cautionary markings on

(1) charger, (2) battery pack, and (3) product using battery pack.

DANGER: 120 volts present at charging terminals. Do not probe with conductive objects.

Danger of electric shock or electrocution.

DANGER: If battery pack case is cracked or damaged, do not insert into charger. Danger

of electric shock or electrocution.

DANGER: Never attempt to open the battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service center for recycling.

WARNING: Don’t allow any liquid to get inside charger. Electric shock may result.

CAUTION: To reduce risk of injury, charge only Black & Decker rechargeable batteries.

Other types of batteries may burst, causing personal injury and damage.

• To facilitate the cooling of the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

• Do not expose charger to rain or snow.

• Use of an attachment not recommended or sold by Black & Decker may result in risk of

fire, electric shock, or injury to persons.

• This charger is not intended for any uses other than charging Black & Decker

rechargeable batteries. Any other uses may result in risk of fire, electric shock or

electrocution.

• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

• Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

• An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock, or electrocution. If an extension

cord must be used, make sure:

• That the pins on plug of extension cord are the same number, size and shape of

those of plug on charger.

• That extension cord is properly wired and in good electrical condition and the wire

size is large enough for AC ampere rating of charger as specified below.

An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable,

that is, 16 gauge has more capacity than 18 gauge. When using more than one extension

to make up the total length, be sure each individual extension contains at least the

minimum wire size.

RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS

TOTAL EXTENSION CORD LENGTH (FEET)

25 50 75 100 125 150 175

WIRE GAUGE

18 18 16 16 14 14 12

• The charger is ventilated through slots in the housing. Do not place any object on top of

charger or place the charger on a soft surface that might block the ventilation slots and

result in excessive internal heat. Place the charger in a position away from any heat source.

• Do not operate charger with damaged cord or plug — have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service or repair

is required. Incorrect reassembly may result in risk of electric shock, electrocution or fire.

• The charger is designed to operate on standard120 VAC, 60Hz household electrical

power. Do not attempt to use it on any other voltage.

• To reduce risk of electric shock, unplug charger from outlet before attempting any

cleaning. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• DO NOT store or use the tool and battery pack in locations where the temperature may

reach or exceed 105°F (such as outside sheds or metal buildings in summer).

• A small leakage of liquid from the battery cells may occur under extreme usage, charging

or temperature conditions. This does not indicate a failure. However, if the outer seal is

broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10

minutes and seek immediate medical attention. The liquid is a MEDICAL NOTE:

25-35% solution of potassium hydroxide.

SAVE THESE INSTRUCTIONS

CHARGING THE BATTERY

THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE

FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF

THE SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power. NOTE: Do not

charge by means of an engine generator or DC power source. Use only 120V AC.

1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.

2. Slide the charger onto the battery pack as shown in and let it charge initiallyFigure 1

for 9 hours. After the initial charge, under normal usage, your power pack should be

fully charged in 3 to 9 hours.

3. Remove pack from the charger and place in tool. To remove the battery fromNOTE:

the saw, press down on the release button on the back of the battery (Figure 2) and

pull out.

IMPORTANT CHARGING NOTES

1. Longest life and best performance can be obtained if the battery pack is charged when

the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery

pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is

important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a

normal condition, and does not indicate a problem.

3. If the battery pack does not charge properly — (1) Check power at receptacle by plug-

ging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light

switch which turns power off when you turn out the lights. (3) Move charger and battery

pack to a location where the surrounding air temperature is approximately 65°F - 75°F

(18°- 24°C). (4) If charging problems persist, take or send the tool, battery pack and

charger to your local service center.

4. The battery pack should be recharged when it does not produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE use under these conditions.

Follow the charging procedures. You may also charge a partially used pack whenever

you desire with no adverse affect on the battery pack.

5. Black & Decker battery packs that are labeled “NiMH” should only be used with chargers

labeled “NiMH“ or “NiCd/NiMH.”

6. Under certain conditions, with the charger plugged into the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or

any buildup of metallic particles should be kept away from charger cavities. Always

unplug the charger from the power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

7. Do not immerse charger in water or any other liquid.

OPERATING INSTRUCTIONS

TRIGGER SWITCH & REVERSING BUTTON - FIGURE 3

The drill is turned ON and OFF by pulling and releasing the trigger switch shown in Figure 3.

The farther the trigger is depressed, the higher the speed of the drill. A forward/reverse

control button determines the direction of the tool and also serves as a lock off button. To

select forward rotation, release the trigger switch and depress the forward/reverse control

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Battery not installed properly. • Check battery installation.

• Battery not charged. • Check battery charging

requirements.

• Battery will not charge. • Battery not inserted into charger. • Insert battery into charger

until red LED appears.

• Charger not plugged in. • Plug charger into a working

outlet. Refer to “Important

Charging Notes” for more

details.

• Check current at receptacle

by plugging in a lamp or other

appliance.

• Check to see if receptacle is

connected to a light switch

which turns power off when

you turn out the lights.

• Surrounding air temperature • Move charger and tool to a

too hot or too cold. surrounding air temperature

of above 40 degree F(4,5°C)

or below 105 degree F

(+40,5°C).

For assistance with your product, visit our website www.blackanddecker.com for the

location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Gear Shifter

Sélecteur de vitesses

Palanca de cambio de engranes

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers

with efficient and reliable power tool service. Whether you need technical advice, repair, or

genuine factory replacement parts, contact the Black & Decker location nearest you. To find

your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge

in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may

be required. Black & Decker owned and authorized Service Centers are listed under

“Tools-Electric” in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state and province to province.

Should you have any questions, contact the manager of your nearest Black & Decker

Service Center. This product is not intended for commercial use.

Free Warning Label Replacement: If your warning labels become illegible or are

missing, call for a free replacement.1-800-544-6986

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUI SOIT, VEUILLEZ APPELER AU

1-800-544-6986

IMPORTANTES MESURES DE SÉCURITÉ - POUR TOUS LES

OUTILS ALIMENTÉS PAR PILES

AVERTISSEMENT! Lire et comprendre toutes les directives. Le non-respect de

toutes les directives suivantes présente des risques de secousses électriques, d’incendie

ou de blessures graves.

CONSERVER CES MESURES.

ZONE DE TRAVAIL

• S’assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et

des endroits sombres présentent des risques d’accidents.

• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme

celles dégagées par des liquides, des gaz ou des poussières inflammables).

Lesétincelles générées par le moteur des outils électriques peuvent enflammer les

poussières ou les vapeurs.

• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu’on utilise

un outil électrique. Une distraction peut entraîner la perte de maîtrise de l’outil.

MESURES DE SÉCURITÉ RELATIVES À L’ÉLECTRICITÉ

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter

l’outil ni tirer sur le cordon pour débrancher l’outil. Éloigner le cordon des sources

de chaleur, des flaques d’huile, des arêtes tranchantes et des pièces mobiles.

Remplacer immédiatement les cordons endommagés. Les cordons endommagés

augmentent les risques de secousses électriques.

• Il faut charger un outil à piles intégrées ou un ensemble de piles seulement dans le

chargeur conçu à cet effet. Un chargeur convenant pour un type de piles peut présenter

un risque d’incendie lorsqu’on s’en sert avec un autre type de piles.

• Utiliser un outil alimenté par piles seulement avec la pile appropriée. L’utilisation de

toute autre pile présente des risques d’incendie.

SÉCURITÉ PERSONNELLE

• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu’on utilise un outil

électrique. Ne pas s’en servir lorsqu’on est fatigué ou affaibli par des drogues, de

l’alcool ou des médicaments. De graves blessures peuvent résulter d’un moment

d’inattention lors de l’utilisation d’un outil électrique.

•Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des

bijoux. Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les

vêtements et les gants des pièces en mouvement qui peuvent les happer.

•Éviter les démarrages accidentels. S’assurer que l’interrupteur est en position hors

tension avant d’insérer la pile. Afin d’éviter les risques de blessures, ne pas transporter

l’outil avec le doigt sur l’interrupteur ni insérer la pile dans un outil dont l’interrupteur est en

position sous tension.

•Enlever les clés de réglage avant de mettre l’outil sous tension. Une clé qui est laissée

sur une pièce rotative de l’outil présente des risques de blessures.

•Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s’assure d’une

meilleure maîtrise de l’outil dans des situations imprévues grâce à une position stable et un

bon équilibre.

•Porter de l’équipement de sécurité. Toujours porter des lunettes de sécurité. Dans

certaines conditions, il faut porter des masques respiratoires, des chaussures

antidérapantes, un casque de sécurité ou des protège-tympans.

UTILISATION ET ENTRETIEN DE L’OUTIL

•Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de

soutenir la pièce à ouvrer sur une plate-forme stable. La pièce est instable lorsqu’elle

est retenue par la main ou le corps de l’utilisateur. Cela présente des risques de perte de

maîtrise de l’outil.

•Ne pas forcer l’outil. Utiliser l’outil approprié à la tâche. L’outil approprié fonctionne

mieux et sûrement lorsqu’on s’en sert à son rendement nominal.

•Ne pas se servir de l’outil lorsque l’interrupteur est défectueux. Le cas échéant, l’outil

est dangereux et il faut le réparer.

•Enlever la pile de l’outil ou placer celui-ci en position hors tension avant de le régler,

d’en remplacer les accessoires ou de le ranger. On minimise de la sorte le risque de

démarrage accidentel de l’outil.

•Ranger l’outil hors de portée des enfants et de toute autre personne qui n’en connaît

pas le fonctionnement. L’outil est dangereux entre les mains de ces personnes.

•Lorsque la pile ne sert pas, l’éloigner de tout objet métallique (comme des

trombones, des pièces de monnaie, des clés, des clous, des vis ou tout autre petit

objets métalliques qui peut créer une connexion d’une borne à l’autre). Lorsque les

bornes sont court-circuitées, cela peut générer des étincelles, des brûlures ou un incendie.

•Prendre soin des outils. S’assurer que les outils de coupe sont tranchants et

propres. Des outils bien entretenus à arêtes tranchantes ont moins tendance à se coincer

et ils se maîtrisent mieux.

•Vérifier l’alignement et les attaches des pièces mobiles, le degré d’usure des pièces

ainsi que tout autre facteur susceptible de nuire au bon fonctionnement de l’outil.

Faire réparer un outil endommagé avant de s’en servir. Des outils mal entretenus sont

la cause de nombreux accidents.

•Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires

qui conviennent à un outil peuvent présenter des risques avec un autre outil.

ENTRETIEN

•Confier l’entretien de l’outil seulement à du personnel qualifié. Le non-respect de la

présente directive présente des risques de blessures.

•Lors de l’entretien de l’outil, utiliser seulement des pièces de rechange identiques.

Respecter les consignes relatives à l’entretien du présent guide d’utilisation. Il y a

risque de secousses électriques ou de blessures lorsqu’on utilise des pièces non

autorisées ou lorsqu’on ne respecte pas les consignes relatives à l’entretien

MESURES DE SÉCURITÉ SPÉCIFIQUES

•Tenir l’outil par les surfaces isolées prévues à cette fin lorsqu’il risque d’entrer en

contact avec des fils cachés ou le cordon,

car de tels contacts peuvent mettre les pièces

métalliques de l’outil sous tension, engendrant des risques de choc électrique.

•

Porter des protecteurs auditifs si une perceuse à percussion est utilisée. Une

exposition au bruit peut entraîner une perte auditive.

•

Utiliser les poignées auxiliaires fournies avec l'outil. Une perte de maîtrise de l'outil

peut entraîner des blessures corporelles.

•Utiliser des brides de fixation ou un autre dispositif de fixation permettant de fixer

solidement et de soutenir la pièce sur une plateforme stable.

Tenir la pièce avec la

main ou contre son corps la rend instable et risque de provoquer une perte de maîtrise de

l’outil.

•Lorsqu’on est installé sur une échelle ou un échafaudage pour travailler, on doit

déposer l’outil sur le côté lorsqu’on ne s’en sert plus. Bien que certains outils munis

d’un gros bloc-piles puissent être placés à la verticale, dans cette position, ils peuvent

facilement être renversés.

AVERTISSEMENT :

:Certaines poussières produites par les activités de ponçage,

de sciage, de meulage, de perçage et autres activités de construction peuvent

contenir des produits chimiques pouvant causer le cancer, des anomalies

congénitales ou d'autres problèmes liés aux fonctions reproductrices. Voici

quelques exemples de ces produits chimiques :

• le plomb contenu dans les peintures à base de plomb;

• la silice cristalline de la brique, du ciment et d'autres produits de maçonnerie; et

• l'arsenic de cuivre et de chrome provenant du bois traité chimiquement.

Les risques reliés à l'exposition à ces poussières varient selon la fréquence à laquelle

vous travaillez avec ce type de matériaux. Afin de réduire votre exposition à ces produits

chimiques : travaillez dans un endroit bien ventilé et portez un équipement de sécurité

approuvé comme un masque anti-poussières conçu spécialement pour filtrer les particules

microscopiques.

• Évitez le contact prolongé avec les poussières produites par les activités de

ponçage, sciage, meulage, perçage et autres activités de construction. Portez des

vêtements de protection et lavez les parties du corps exposées avec une solution

d'eau et de savon. Le fait de laisser la poussière pénétrer par la bouche et les yeux, ou

de la laisser reposer sur la peau, peut promouvoir l'absorption de produits chimiques nocifs.

AVERTISSEMENT : Cet outil peut produire et répandre de la poussière

susceptible de causer des dommages sérieux et permanents au système

respiratoire. Toujours utiliser un appareil respiratoire anti-poussières approprié approuvé

par le NIOSH ou l’OSHA. Diriger les particules dans le sens opposé du visage et du corps.

LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS

Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il

contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les

symboles ci-dessous servent à vous aider à reconnaître cette information.

DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera

la mort ou des graves blessures.

AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle n’est

pas évitée, pourrait causer la mort ou de graves blessures.

MISE EN GARDE : Indique une situation potentiellement dangereuse qui, si elle n’est pas

évitée, pourrait causer des blessures mineures ou modérées.

MISE EN GARDE : Utilisé sans le symbole d’alerte à la sécurité, indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée, peut résulter en des dommages à la

propriété.

L’étiquette de l’outil peut comporter les symboles suivants.

V ....................................volts A..........................ampères

Hz ..................................hertz W ........................watts

min..................................minutes ......................courant alternatif

................................courant continu no ........................sous vide

....................................Construction de classe II ........................borne de mise à la

minute

..................................symbole d´avertissement .../min ..................tours ou courses

à la minute

INFORMATION CONCERNANT LE CAPUCHON DU BLOC-PILE

Un capuchon est fourni avec le bloc-pile en vue d’être utilisé chaque fois qu’on retire ce

dernier de l’outil ou du chargeur en vue de le ranger ou de le transporter; enlever le

capuchon avant de remettre le bloc-pile dans le chargeur ou dans l’outil.

AVERTISSEMENT : S’assurer, au moment de ranger ou de transporter un bloc-pile ou

une pile, qu’aucun objet métallique n’entre en contact avec leurs bornes à découvert de

celui-ci. Par exemple, il faut éviter de placer un bloc-pile ou une pile sans capuchon dans un

tablier, une poche, une boîte à outils ou un tiroir (etc.) contenant des objets tels que des

clous, des vis ou des clés, car tout contact entre les bornes à découvert et un objet

métallique comme une clé, une pièce de monnaie, un outil à main. etc. pourrait causer un

incendie. En effet, les règlements américains Hazardous Material Regulations (HMR) du

US Department of Transportation interdisent le transport d’un bloc-pile ou d’une pile dans

tout moyen de transport commercial ou aéronef (que ce soit dans une valise ou le bagage

de cabine) SAUF s’ils sont bien protégés contre les courts-circuits. On doit donc s’assurer,

lorsqu’on transporte un bloc-pile ou une pile séparément, de bien protéger et isoler les

bornes contre tout matériau qui risque d’entrer en contact avec eux et de causer un

court-circuit.

MESURES DE SÉCURITÉ IMPORTANTES

•CONSERVEZ CES DIRECTIVES.

• Bien lire toutes les directives et tous les avertissements qui se trouvent sur (1) le

chargeur, (2) l’ensemble de piles et (3) l’outil avant d’utiliser le chargeur.

DANGER : Les bornes du chargeur sont sous une tension de 120 volts. Ne pas les

examiner avec un objet conducteur; cela présente des risques de secousses électriques.

DANGER : Ne pas placer dans le chargeur un ensemble de piles craqué ou endommagé;

cela présente des risques de secousses électriques.

MISE EN GARDE : Ne jamais tenter d’ouvrir un ensemble de piles. Lorsque le boîtier en

plastique craque ou se casse, en confier le recyclage à un centre de service.

AVERTISSEMENT : Ne laisser aucun liquide s’infiltrer dans le chargeur car cela

représente des risques de secousses électriques.

MISE EN GARDE : Afin de réduire les risques de blessures, charger seulement des piles

rechargeables Black & Decker. Tout autre type de piles peut exploser; ce qui présente des

risques de blessures et de dommages.

Capuchon du bloc-pile

Produktspezifikationen

Marke:	Black And Decker
Kategorie:	bohren
Modell:	HPD1400

Brauchst du Hilfe?

Wenn Sie Hilfe mit Black And Decker HPD1400 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung bohren Black And Decker

Black And Decker GC1800 Bedienungsanleitung

13 Oktober 2024

Black And Decker KD664 Bedienungsanleitung

4 Oktober 2024

Black And Decker XD1200 Bedienungsanleitung

4 Oktober 2024

Black And Decker HD455KA Bedienungsanleitung

29 September 2024

Black And Decker PS3500 Bedienungsanleitung

21 September 2024

Black And Decker FSD962 Bedienungsanleitung

20 September 2024

Black And Decker FS7000D Bedienungsanleitung

17 September 2024

Black And Decker CD18SR Bedienungsanleitung

15 September 2024

Black And Decker HP1800 Bedienungsanleitung

14 September 2024

Black And Decker CD96C Bedienungsanleitung

13 September 2024

Bedienungsanleitung bohren

Neueste Bedienungsanleitung für -Kategorien-

Ozito BDP-500 Bedienungsanleitung

16 Oktober 2024

MSW -DDM255 Bedienungsanleitung

16 Oktober 2024

MSW -DDM152 Bedienungsanleitung

16 Oktober 2024

MSW -DDM205 Bedienungsanleitung

16 Oktober 2024

MSW -DDM230 Bedienungsanleitung

16 Oktober 2024

Einhell BM-G1100 E Bedienungsanleitung

15 Oktober 2024

Sun Joe 24V-DDK-LTX-PNK Bedienungsanleitung

15 Oktober 2024

Makita DHR263ZJ Bedienungsanleitung

13 Oktober 2024

Rupes BH 252R Bedienungsanleitung

13 Oktober 2024

Einhell RT-RH 20/1 Bedienungsanleitung

13 Oktober 2024