Biodrier Biobot Bedienungsanleitung
Biodrier
Händetrockner
Biobot
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Biodrier Biobot (15 Seiten) in der Kategorie Händetrockner. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/15
Biobot
Hand dryer
Automatic
High Speed
Technical Specications
Item Category Performance Data
Operating Voltage 220 - 240Vac, 50Hz, 900 WATTS
Warm Air Speed Output 64 m/s
Air Output Temperature 77°F (25°C) - Ambient Temperature 68°F (20°C)
Motor Type 23,000 rpm, Brush Type, Dual Ball Bearings
Motor Thermal Protection Auto Resetting Thermostat turns unit o,
240V at 221°F (105°C) - EURO Spec
Heater Element 250W
Heater Thermal Protection Auto Resetting Thermostat turns unit o at, 149°F (65°C)
Drying Time Less than 15 seconds
Circuit Operation Infared Automatic, self adjusting
Sensor Range 100 mm
Timing Protection 60 seconds auto shut o
Drip Proof IP22
Isolation CLASS 1
Net Weight 4.5 kg
Shipping Weight 5 kg
Unit Size 280mm W x 300mm H x 175mm D
Item Code Cover Type/Finish
BB08 Die Cast Aluminium; Epoxy Polyester Powder Coating (Blue)
Operating Instructions and Parts Manual (Automatic)
Eco Surface Mounted High Speed Hand Dryer
Biobot
1
300mm
280mm
175mm
Operating Instructions and Parts Manual (Automatic)
Eco Surface Mounted High Speed Hand Dryer
General Safety Information
• WARNING
Failure to properly ground unit could result in
electrical shock and/or death.
This product is intended for installation by a
qualied service person. Use AWAG No.16 solid
conductor for wiring.
Disconnect power at the service breaker before
installing or servicing.
NOT FOR HOUSEHOLD USE - MAY CAUSE BURNS
“IMPROPRE A L’USAGE DOMESTIQUE - PUET
OCCASIONNER.”
All units must be supplied with a 3-wire service. The
ground wire must be connected with the dryers
back plate.
NOTE: Do not install dryer over wash basin.
Type Y attachment
If the power supply cord is damaged, it must be
replaced by the manufacturer or its service agent or a
similar qualied person in order to avoid a hazard.
Means for disconnection must be incorporated in the
xed wiring in accordance with the wiring rules.
2
Biobot
Installation
1. Make sure power supply breaker is switched o.
Installation must be carried out in accordance with the
current edition of the local wiring regulations code
having jurisdiction. Installation should be performed
only by a qualied electrician.
2. Place template against wall at desired height
(see mounting height recommendations) and mark
locations of 4 mounting holes and wire service entry at
knockout (KO) location.
NOTE: For two or more dryers, dryers should be no
closer than 24 inches (610 mm) on centre.
3. Remove and retain 2 cover screws and cover.
4. Connect supply wires to terminal block where
indicated and connect ground wire to baseplate with
ground screw.
Connections:
a. Connect the live wire (coloured red or brown) to
the terminal block marked “L”.
b. Connect the neutral wire (coloured black or blue)
to the terminal block marked “N”.
c. Connect the ground wire (coloured green or green
and yellow) to the green screw marked “ ”.
Note that the colour of live and neutral wires depends
on voltage of supply service.
5. Replace cover. Do not over-tighten screws.
Produktspezifikationen
| Marke: | Biodrier |
| Kategorie: | Händetrockner |
| Modell: | Biobot |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Biodrier Biobot benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Händetrockner Biodrier
15 September 2023
Bedienungsanleitung Händetrockner
- Händetrockner Mitsubishi
- Händetrockner Dyson
- Händetrockner Honeywell
- Händetrockner Thermex
- Händetrockner Stiebel Eltron
- Händetrockner Dimplex
- Händetrockner Noirot
- Händetrockner Starmix
- Händetrockner Vortice
- Händetrockner Royal Sovereign
- Händetrockner Fantini Cosmi
- Händetrockner American Dryer
- Händetrockner Bobrick
Neueste Bedienungsanleitung fĂĽr -Kategorien-
9 Oktober 2024
11 August 2024
16 Mai 2024
21 März 2024
19 März 2024
13 März 2024
4 Februar 2024
2 Februar 2024
25 Januar 2024