Binatone Action 950 Bedienungsanleitung

Binatone Radio Action 950

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Binatone Action 950 (10 Seiten) in der Kategorie Radio. Dieser Bedienungsanleitung war fĂĽr 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/10
USER GUIDE
Private mobile radio with twin charger
1. LCD Screen
Antenna
LCD Screen
- Displays the
current channel
selection and other
radio s ymbols.
PTT (PUSH to
TALK) button
–Press and hold to
transmit. CALL button
-Press to send
Ringing tone to
other PMR units.
MENU Button
-Press to switch
between Modes.
Sp reake
Ear/Mic/Charge
jack
PWR/VOL Switch
– Rotate clockwise/
counter clockwise
to turn
ON or OFF, and
adjust the volume.
MIC (Microp )hone
UP/DOWN
Buttons –
Press to change
channels, volume,
and to select
settings during
p g gro rammin .
the unit
Channel Number. Changes from 1 to
8 as selected by the user.
Digital Code. Changes from 1 to 83
as selected by the user.
Displays the Battery charge level.
When the bars are reduced, the
battery needs recharging.
TX Displayed when transmitting a signal.
RX Displayed when receiving a signal.
DCS Displayed when the Digital Code System is turned On.
VOX Displayed when the VOX feature is enabled.
SCAN Displays when the PMR is scanning all channels.
Displayed when the Key Lock feature is activated.
Displayed when a CTCSS sub-channel is turned on.
Displays when the call signal is ON.
Displays when the vibrator function is activated.
Action 950
CTCSS Code. Changes from 1 to 38
as selected by the user.
Displayed when the Dual Watch function is turned ON.
DCM
CTCSS
Receiver (LED)
Lights up when you
are receiving signals
Transmit (LED)
2. Installation
2.1 Removing the Belt Clip
2.2 Installing the Belt Clip
2.4 Charging the Batteries
a. Pull the Belt Clip latch up
(away from the ) Action 950
b. While pulling the Belt Clip
latch,slide the Belt Clip up as
shown in Figure1.
Belt Clip latch
Fig gure 1 Fi ure 2
a. Slide the Belt Clip into the
slot as shown in Figure2.
A “click” indicates the Belt
Clip is locked into position.
Fig gure 3 Fi ure 4
a. Unclip the battery cover latch at the bottom of the cover, and lift
the battery cover off.
Important
Read these Safety Warnings before you charge the batteries.
When placing the Action 950 in the charger, use only the power
supplies listed in the user instructions supplied with the Action 950.
Don’t try to recharge non-rechargeable batteries.
Make sure the battery compartment cover is securely locked in
place when you are charging the batteries.
Dispose of used batteries safely and in a way that will not harm
the environment- never try to burn them or put them anywhere they
could get burnt or punctured.
Don’t leave dead batteries in your units. Action 950
They might leak if you do.
a. Insert the small plug on the end of the mains adaptor into the
Power-in Connection Jack at the back of the desktop charger.
b. Plug the mains adaptor into a 240V AC, 50Hz main socket with
the switch on the socket set to OFF.
c. Switch ON the mains socket.
Using any other adaptor will result in non-compliance with
EN60950-1 and will invalidate any approvals & warranty.
2.3 Installing the Batteries
Caution: Observe the proper battery polarity orientation when
installing batteries. Incorrect positioning can damage both the
batteries and the unit.
b. Insert the 4 “AAA” size rechargeable batteries by following the
c. Replace the Battery Compartment Cover. See Figure 4.
+ polarity marking inside the Battery Compartment as shown in /-
Figure 3.
Use only the mains adaptor provided.
%DWWHU\ PHWHU
%DWWHU\ OLIH
d. P g a p g p i nlace the uni s the char Action 950 t in e cradle in n u ri ht os tio .
The Charge LED indicators will light up.
completely run down. New batteries take up to 14 hours to fully
charge.
e. It takes about 10 hours to fully recharge the batteries if they are
Important:
Always turn off the PMR units
when charging. This will
shorten the charging time.
Mains socket
OR: Charging the batteri s ( sing ada tor) e u p
Lift the charge socket cover located on
the right side of the handset.
Insert the round connector of
the 9.0V DC/200mA adaptor
into the charge jack.
Plug the mains adaptor into a
240V AC, 50Hz main socket
with the switch on the socket
set to OF . e onlyF Us the mains
adaptor provided.
Then switch ON the mains socket.
Mic/Earpiece jack
Charge jack
The battery meter is located in the left corner of the LCD Screen. It
appears like a battery with three bars inside. These indicate the
amount of power available. When the battery level reaches its
minimum level in PMR on mode, the unit will emit two beep tones
and automatically power off.
The can detect the battery charge in 4 levels; Action 950
Battery charge at high level.
Battery charge at medium level.
Battery charge at low level. At this level, the Action 950 will
Important: Charge the unit for 10-14 hours.
Battery charge at very low level. When the battery level
reachs its minimum level in Action 950 on mode, the unit will
Important: Charge the unit for 10-14 hours.
CAUTION : Risk of explosion if battery is replaced by an
inco rect pe. D spos of used batter es ac o d ng to ther ty i e i c r i
instructions.
The Action 950 h as a built in power saver to make the batteries
emit a “beep” sound for every 10 seconds in normal mode.
emit two beep tones and automatically turn off the
power .
last longer. But when you are not using the units, turn them
OFF to conserve battery power.
c
ll
a


Produktspezifikationen

Marke: Binatone
Kategorie: Radio
Modell: Action 950

Brauchst du Hilfe?

Wenn Sie Hilfe mit Binatone Action 950 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Radio Binatone

Bedienungsanleitung Radio

Neueste Bedienungsanleitung fĂĽr -Kategorien-