BeSafe IZi Go Modular i-Size Bedienungsanleitung

BeSafe Autositz IZi Go Modular i-Size

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für BeSafe IZi Go Modular i-Size (98 Seiten) in der Kategorie Autositz. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/98
1 3
4
5
2
b
c
e
h
g
d
f
a
i
k
m
l
j
click!
> 25 cm
USER MANUAL
Max. weight 13 kg
Age 0-12 mths
UN regulation no. R129
i-Size
Stature height 40-75 cm
104
110
116
122
128
134
140
146
152
158
164
170
176
187
193
199
1
14
20
26
32
38
44
50
56
62
68
74
80
86
92
98
8 9
! Vital information
• The child seat MUST NOT be installed in a front
passenger seat WITH AN ACTIVATED AIRBAG.
• iZi Go Modular can be installed rearfacing on iZi
Modular i-Size base or can be installed rearfacing with a 3-point
car belt, approved according to UN/ECE Regulation No.16 or other
equivalent standards.
• iZi Go modular is approved for children with a stature height from
40 to 75 cm, with a max. weight of 13 kg.
• The harness straps must always be locked when the child is in
the seat.
• The harness straps must be tightened without slack and not twisted.
• The shoulder pads contain magnets. Magnets can influence
electronic equipment such as pacemakers.
• Protect any part of the child’s body which is exposed to the sun.
• Remove the head space reducers on both sides from the headrest
when the child is older than 3 months or if the head is not tting
anymore. These reducers can be removed by opening the velcro on
the back of the head rests.
• Remove the baby cushion (bottom part) when the child is taller
then 60 cm, or over 4 months.
• Remove the baby cushion (bottom part) and body hugger (upper
part) when the child is taller than 65 cm, or over 6 months.
• After an accident, the seat must be replaced. Although it may look
undamaged, if you were to have another accident, the seat may not
be able to protect your child to the level to which it was designed.
• Prevent the seat from becoming trapped or weighed down by
luggage, seats and/or slamming doors.
• Make sure you can fit no more than one finger between the harness
and your child (1 cm).
• DO NOT attempt to dismantle, modify or add any part to the seat.
Warranty will be void if non-original parts or accessories are used.
• Never leave your child unattended in the seat.
• Make sure all passengers are informed about how to release your
child in case of emergency.
6
8
9
7 10 11 16
19
20 21
17 18
12
14
15
13
click!
< 60 cm
0-4 months
60-65 cm
4-6 months
> 65 cm
> 6 months
Thank you for choosing BeSafe iZi Go Modular
! It is important that you read this user manual BEFORE
installing your seat. Incorrect installation could endanger
your child.
10 11
• Carrying handle (1a)
• Head cushion (1b)
• Head space reducer (1c)
• Handle release buttons (2x) (1d)
• Shoulder straps (2x) (1e)
• Hip belt hook (2x) (1f)
• Baby cushion (1g)
• Harness buckle (1h)
• Sun canopy (1i)
• Stroller release handles (4x) (1j)
• Shoulder belt hook (1k)
• Harness height adjuster (1l)
• Stroller adapter house (1m)
Preparing to install
Installation of the seat on the i-Size base
Removal of the seat of the i-Size base
Belt installation
1. Check if the ISOfix and floor support indicators on the base
are green. (2)
2. Position the seat in the correct position on the base untill it clicks
with the base and the indicator at the front shows green. (3)
3. Leave the carrying handle up in the carrying position.
4. When the seat is positioned rearfacing on the back seat of the
vehicle, you should, if possible, push the front seat of the vehicle
backwards, so that it is in contact with the child seat. If it is not
possible to obtain contact with the child seat, push the back rest of
the front seat of the vehicle forward as far as possible. (4)
5. The seat is delivered with removable SIP+ (side impact protection +).
This extra side impact protection should be used on the doorside of
the vehicle. It can be connected by slotting between the seatshell and
the fabric. The seat already oers high level integrated side impact
protection. This extra side impact protection improves the protection
in the side impact still further. (Not on all models) Do not use the
SIP+ on the seat when the space between seat and door of the
vehicle is too small, which might lead to a situation where the seat is
not positioned correctly on the vehicle seat.
• The seat can be taken o by pulling the seat release handle at the
front of the base.
1. Position the seat on the vehicle seat. Make sure the carrying handle
is up in the carrying position. (5)
2. Guide the hip belt of the 3-point-belt over the blue sections under
the hip belt hooks and fasten the seat belt with a ‘click’. (6)
3. Guide the shoulder belt over the blue section through the shoulder
belt hook at the rear side of the seat shell. (7)
4. Tighten the 3-point belt by pulling the belt through the hip belt
hooks and through the shoulder belt hook until it is as tight as
possible. (8)
5. Leave the carrying handle up in carrying position.
Positioning of the child
Baby cushion
1. Check that the shoulder strap slots are level with your child’s
shoulders. (9)
2. Pull the shoulder straps up while pressing the button of the central
adjuster. (10)
3. Open the harness buckle. (11)
4. The height of the shoulder straps and the head cushion can be
adjusted by pulling the release handle upwards at the back of the
seat and pulling the handle up or down. (12)
5. Position the shoulder straps over the marking at the sides of the seat
to use the magnets to keep the harness open while you position the
child. (13)
6. When the child is positioned, place the shoulder straps over the
child’s shoulders and close the buckle: CLICK! (14)
7. Pull the harness strap through the central adjuster in the direction of
the arrow straight up/forwards. Continue pulling until the harness is
a comfortable but a rm t. (15)
8. You can protect your child against the sun by raising the sun canopy.
The baby cushion oers extra comfort for young babies. As baby grows
the thickness of the baby cushions can be adjusted.
• 0-4 m (16)
• 4-6 m (17)
• 6 m + (18)

Produktspezifikationen

Marke: BeSafe
Kategorie: Autositz
Modell: IZi Go Modular i-Size

Brauchst du Hilfe?

Wenn Sie Hilfe mit BeSafe IZi Go Modular i-Size benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Autositz BeSafe

BeSafe

BeSafe iZi Flex S fix Bedienungsanleitung

27 August 2024
BeSafe

BeSafe Tablet and Seat Cover Bedienungsanleitung

27 August 2024
BeSafe

BeSafe combi Bedienungsanleitung

27 August 2024
BeSafe

BeSafe IZI Modular Isofix base Bedienungsanleitung

27 August 2024
BeSafe

BeSafe iZi Go X1 - 2015 Bedienungsanleitung

27 August 2024
BeSafe

BeSafe iZi Turn i-Size Bedienungsanleitung

21 August 2024
BeSafe

BeSafe IZi Kid i-Size Bedienungsanleitung

21 August 2024
BeSafe

BeSafe IZi Sleep ISOfix Bedienungsanleitung

21 August 2024
BeSafe

BeSafe iZi Modular X1 i-Size Bedienungsanleitung

21 August 2024
BeSafe

BeSafe iZi Turn E-M i-Size Bedienungsanleitung

20 August 2024

Bedienungsanleitung Autositz

Neueste Bedienungsanleitung fĂźr -Kategorien-

RĂśmer

RĂśmer EVOLVA 1-2-3 plus Bedienungsanleitung

14 Oktober 2024
Lorelli

Lorelli Jupiter Bedienungsanleitung

5 Oktober 2024
Joie

Joie i-Prodigi Bedienungsanleitung

30 September 2024
RĂśmer

RĂśmer BABY-SAFE plus SHR II Bedienungsanleitung

27 September 2024
Cosatto

Cosatto Zoomi Bedienungsanleitung

24 September 2024
Cosatto

Cosatto Axkid Minikid 4 Bedienungsanleitung

24 September 2024
Cosatto

Cosatto All in All Ultra Rotate i-Size Bedienungsanleitung

24 September 2024
Cosatto

Cosatto All in All 360 Rotate i-Size Bedienungsanleitung

24 September 2024
Cosatto

Cosatto Acorn 2 i-Size Bedienungsanleitung

24 September 2024
Xadventure

Xadventure Junior Isofix Bedienungsanleitung

23 September 2024