Bertazzoni PRO30 4 GAS VI Bedienungsanleitung

Bertazzoni Herde PRO30 4 GAS VI

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Bertazzoni PRO30 4 GAS VI (28 Seiten) in der Kategorie Herde. Dieser Bedienungsanleitung war fĂĽr 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/28
Installation, Service and User Instructions
FREESTANDING GAS RANGES
BERTAZZONI
DIMENSIONS: 30’’ (762 mm)(W) x 253/16’’ (640 mm)(D) x36’’ (915 mm)(H)
Models X304GGVX [M7S0GTU4X(2 or 5)A]
IMPORTANT - PLEASE READ AND FOLLOW
-Before beginning installation, please read these instructions completely and carefully.
-Do not remove permanently affixed labels, wa may void the warranty. -Please observe alrnings, or plates from the product. This l local
and national codes and ordinances.
-Please ensure that this product is properly grounded.
-The installer should leave these instructions with the consumer who should retain for local inspector's use and for
future reference.
-The electrical plug should always be accessible.
Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1-latest edition. Electrical
installation must be in accordance with the National Electrical Code, ANIS/NFPA70
- latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas Installation Code or CAN/CGA-B
149.2, Propane
Installation Code and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.
Installation of any gas-fired equipment should be made by a licensed plumber. A manual gas shut-off valve must be installed in the gas
supply line ahead of the oven in the gas flow for safety and ease of service.
In Massachusetts: All gas products must be installed by a "Massachusetts" licensed plumber or gasfitter. A "T" handle type manual
gas valve must be installed in the gas supply line to this appliance.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
OBSERVE ALL GOVERNING CODES AND ORDINANCES.
WARNING: If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal injury
or death.
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
- Do not light any appliance.
- Do not touch any electrical switch.
- Do not use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions.
- If you cannot reach your gas suppliers, call the fire department.
Installation and service must be performed by a qualified installer,
service agency or the gas supplier.
310240
Warning!
- This range can tip. Injury to persons could result.
- Install anti-tip device shipped with range.
-See Installation Instructions
2
WARNING
Read this instruction booklet before installing and using the appliance.
The manufacturer will not be responsible for any damage to property or to persons caused by
incorrect installation or improper use of the appliance.
The manufacturer reserves the right to make changes to its products when considered necessary and useful,
without affecting the essential safety and operating characteristics.
This appliance has been designed for non-professional, domestic use only.
Warning: do not place any pot or pan on the open oven door. The door is made of glass and it can
break if loaded with a weight.
Warning: this appliance must be used only with base feet properly installed. See installation
instruction for details.
Installation instructions
This appliance shall only be installed by an authorized person. This appliance shall be installed in
accordance with the manufacturer’s installation instructions, IMPORTANT: this appliance must be
installed in accordance with the norms & standards of the country where it will be installed.
The installation of this appliance must conform to local codes and ordinances. In the absence of
local codes, Installations must conforms to American National Standards, National Fuel Gas Code
ANSI Z223.1 – latest edition** or B149.1.
If local codes permit, a flexible metal appliance connection with the new AGA or CGA certified
design, max. 5 feet (1,5 m) long, ½” I.D. is recommended for connecting this appliance to the gas
supply line. Do not bend or damage the flexible connector when moving the appliance. The pressure
regulator has ½” female pipe thread. The appropriate fitting must be determined based on the size of
your gas supply line, the flexible metal connector and the shutoff valve.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in
the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.
The appliance must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal
to or less than ½ psi (3.5 kPa).
For use with a pressure regulator. The regulator supplied must be used with this appliance; it shall
be properly installed in order to be accessible when appliance is installed in its final location.
The gas appliance pressure regulator must be set for the gas with which the appliance is used.
This appliance can be used with Natural Gas and LP Gas. It is shipped from the factory adjusted for
use with Natural Gas: CONVERSION FIXED ORIFICES ARE LOCATED IN THE LITERATURE PACK
SUPPLIED WITH THE UNIT.
A gas nozzle kit for the change of type of gas are contained inside the package together with the
gas appliance installation kit and instruction booklet.
The maximum inlet gas supply pressure incoming to the gas appliance pressure regulator is 20’’
water column (5 kPa) .
The minimum gas supply pressure for checking the regulator setting shall be at least 1“ w.c. (249 Pa)
above the inlet specified manifold pressure to the appliance (this operating pressure is 4” w.c.
(1.00 kPa) for Natural Gas and 11” w.c. (2.75 kPa for LP Gas).
All opening and holes in the wall and floor, back and under the appliance shall be sealed before
installation of the appliance.
ATTENTION: A manual valve shall be installed in an accessible location in the gas line external to the
appliance for the purpose of turning on or shutting off gas to the appliance
WARNING: Do not use aerosol sprays in the vicinity of this appliance while it is in operation
3
Requirements
Room ventilation – Location and venting.
ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in
conformity with the appropriate national and local standards.
ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be
installed in conformity with the appropriate national and local standards.
INSTALLATION MANUAL
ANTI-TIP STABILlTY DEVICE INSTALLATION INSTRUCTIONS
1. The anti-tip bracket have to be installed to the rear wall as shown. The height for the bracket location from
the floor has to be determined after the range legs have been adjusted to the proper installation height - as
shown in the installation instructions – and after the range has been leveled.
2. Measure from the floor to the bottom of the anti-tip bracket location on the back of the range.
3. Position the two anti-tip brackets on the wall at the measured dimension plus 1/8" (0.32 cm). The brackets
have to be placed at 2”5/16 (6,0 cm) from the side of the range. The distance between the two bracket is
31”1/4 (79,3 cm) clearance. Secure with suitable inserts.
4. Slide the range against the wall until the brackets are fully inserted into the holes on the backside of the
range..
Height adjustable legs:
1. Legs are packed in the top box.
2. Legs should be installed with the appliance being near the location of final installation, they are not secure
for long transport. After unpacking the range, raise it about a foot to insert the legs in their bases assembled
on the lower part of the cooker and lower the range gently to keep any undue strain from legs and mounting
hardware. It is recommended to use a pallet or lift jack instead of tilting the unit.

Produktspezifikationen

Marke: Bertazzoni
Kategorie: Herde
Modell: PRO30 4 GAS VI

Brauchst du Hilfe?

Wenn Sie Hilfe mit Bertazzoni PRO30 4 GAS VI benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Herde Bertazzoni

Bertazzoni

Bertazzoni MAS365GASBIV Bedienungsanleitung

20 Juni 2024
Bertazzoni

Bertazzoni PRO486IGFEPCAT Bedienungsanleitung

12 Juni 2024
Bertazzoni

Bertazzoni PRO105I2EXT Bedienungsanleitung

11 Juni 2024
Bertazzoni

Bertazzoni PRO1005GGVLXE Bedienungsanleitung

1 Juni 2024
Bertazzoni

Bertazzoni P905CAPROX Bedienungsanleitung

1 Juni 2024
Bertazzoni

Bertazzoni MAS95C2EXC Bedienungsanleitung

31 Mai 2024
Bertazzoni

Bertazzoni MAS105I2ENEC Bedienungsanleitung

31 Mai 2024
Bertazzoni

Bertazzoni MAS95C1EXC Bedienungsanleitung

31 Mai 2024
Bertazzoni

Bertazzoni MAS106L3ENEC Bedienungsanleitung

31 Mai 2024
Bertazzoni

Bertazzoni MAS95C2ENEC Bedienungsanleitung

31 Mai 2024

Bedienungsanleitung Herde

Neueste Bedienungsanleitung fĂĽr -Kategorien-

Nemco

Nemco 9130A Bedienungsanleitung

18 August 2024
Meireles

Meireles MI 1600 Bedienungsanleitung

12 August 2024
BEKO

BEKO HIGG 64123 SB Bedienungsanleitung

5 August 2024
NABO

NABO KFC 6060 Bedienungsanleitung

28 Juni 2024
NABO

NABO KFI 6010 Bedienungsanleitung

28 Juni 2024
NABO

NABO KFC 3000 Bedienungsanleitung

28 Juni 2024
NABO

NABO HS 4062 Bedienungsanleitung

28 Juni 2024
AEG

AEG TI64IB10IZ Bedienungsanleitung

27 Juni 2024
BORA

BORA M Pure Bedienungsanleitung

27 Juni 2024
BORA

BORA Basic Bedienungsanleitung

27 Juni 2024