BeefEater Signature BS12850 Bedienungsanleitung

BeefEater Grill Signature BS12850

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für BeefEater Signature BS12850 (24 Seiten) in der Kategorie Grill. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/24

FOR OUTDOOR USE ONLY AUSTRALIA / NEW ZEALAND

Assembly and Operating Instructions SL4000S

SERIES

STAINLESS STEEL

BARBECUES

CONTENTS

Important safety instructions ��3

For built-in units only ��4

Assembly of main barbecue ��5

Assembly of optional rotisserie��7

Assembly of accessories ��8

Installation instructions ��9

Using your barbecue ��13

Getting the most from your barbecue ��15

Cleaning your barbecue ��17

Care and maintenance ��19

Help guide ��20

Specifications �� 21

Notes ��22

Warranty ��23

Please read the user manual carefully and store in a handy

place for later reference�

The symbols you will see in this booklet have these

meanings:

WARNING

This symbol indicates information concerning your

personal safety.

CAUTION

This symbol indicates information on how to avoid

damaging the appliance.

IMPORTANT

This symbol indicates tips and information about use

of the appliance.

ENVIRONMENT

This symbol indicates tips and information about

economical and ecological use of the appliance.

Dear customer,

Congratulations and thank you for choosing our barbecue�

We are sure you will find it a pleasure to use� Before you use

the barbecue, we recommend that you read through the

relevant sections of this manual, which provide a description

of your appliance and its functions�

To avoid the risks that are always present when you use

an appliance, it is important that the appliance is installed

correctly and that you read the safety instructions carefully

to avoid misuse and hazards�

We recommend that you keep this instruction booklet

for future reference and pass it on to any future owners�

After unpacking the appliance, please check it is not

damaged� If in doubt, do not use the appliance but contact

your local customer care centre�

This appliance complies with requirements of Australian

Standards AS4557�

CONDITIONS OF USE

These important notes apply to your appliance

• This appliance must be serviced only by a qualified

licenced person�

• This product is intended for personal, domestic or

household use only, not commercial use�

• This product is intended for outdoor use only�

• This product must be installed, operated and maintained

as per the instructions�

• Ventilation holes in the unit must not be obscured by the

installation�

Please ensure you read the instruction manual fully

before you call for service, or a full service fee could

be applicable.

Record model and serial number here:

Model number: ��

Serial number: ��

PNC: ��

CONTENTSCONGRATULATIONS

3SAFETY

WARNING

We want you to enjoy your barbecuing experience - Failure

to follow the instructions and observe the warnings

provided in this operating manual could result in serious

bodily injury or damage to property.

NOTE TO INSTALLER: This manual must remain with the

owner for future reference�

For Your Safety

1� Do not store or use gasoline or other flammable

vapours or liquids in the vicinity of this or any other

appliance�

2� An LPG cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance�

• Some foods produce flammable fats and juices� Regular

cleaning is essential�

Warning: If you smell gas, shut off gas supply and extinguish

any open flame� If odour continues immediately call your gas

supplier�

• Attend an operating barbecue at all times� Damage

caused by fat & grease fires is not covered by warranty�

• When not in use keep barbecue and side burner dry and

covered�

CAUTION

If your barbecue incorporates an electrical component,

such as a rotisserie, then it must be electrically grounded

in accordance with local codes� The electric cord must

be equipped with a three-prong (grounding) plug for your

protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle� Do

not cut or remove the grounding prong from this plug� Keep

any electrical supply cord and the fuel supply hose away

from any heated surfaces�

If an external electrical source is utilised, this outdoor

cooking appliance, when installed, must be electrically

grounded in accordance with the local codes or, in the

absence of local codes with the following:

USA: National Electrical Code, ANSI/NFPA 70

CAN: Canadian Electrical Code, CSA C22�1

AUS: Aust Standards Code AS:5601

WARNING

Contact your local municipality for any building codes

regulating the installation of outdoor barbecue appliances.

Outdoor installations must conform to local codes or, in the

absence of local codes, with the following:

USA: National Fuel Gas Code, ANSI Z223�1/NFPA 54

CAN: B149�1 Natural Gas & Propane Installation Code�

AUST: Australian Standards Code AS: 5601

as well as the requirements of any local council, gas,

electricity authority or other statutory regulation�

For Your Safety

If you smell gas:

1� Shut off gas to the appliance�

2� Extinguish any open flame�

3� Open lid�

4� If odour continues, immediately call your gas supplier

or your fire department�

When using an LPG supply system in an enclosure,

ventilation must be provided. Gas vapour is highly explosive

and can cause serious bodily injury or damage to property if

allowed to accumulate in a confined space and ignited.

This appliance must not be installed under or on

any combustible material. Minimum clearance from

combustible materials to all sides of the appliance is

450mm (18”).

These specifications must be left with the owner.

This appliance must be installed in accordance with

the installation requirements of the LOCAL GAS and

ELECTRICITY supply authority, or the appropriate

installation code relevant to your country�

USA

Fuels used in gas or oil-fired appliances, and the products

of combustion of such fuels, contain chemicals known to

the state of California to cause cancer, birth defects and /

orother reproductive harm� This warning is issued pursuant

to the California Health & Safety Code Sec� 25249�6�

The Gas cylinder must be constructed and marked in

accordance with specifications for LP Gas Cylinders Stand

of Canada, CAN/CSA - B339, Cylinders, Spheres or Tubes

for the transportation of dangerous goods� The gas cylinder

used must incorporate a safety collar to protect the valve

assembly� The gas cylinder supply valve must be turned off

when the appliance is not in use�

IMPORTANT SAFETY INSTRUCTIONS

4FOR BUILT-IN UNITS ONLY

FOR BUILT-IN UNITS ONLY

The SL4000 comes in both trolley-mounted and built-in

models. These two pages contain information relating to

setting up built-in model only.This appliance is designed

to be used with a gas cylinder not exceeding 9KG (20lbs)

capacity.

About The Cylinder Enclosure

If the gas for your barbecue is to be supplied by a portable

gas cylinder, you will need to ensure that adequate provision

is made to house the cylinder safely� The following must be

adhered to:

Keep out of heat: The cylinder and hose must be sheltered

from the sun’s direct heat� The flexible PVC hose assembly

supplied must not be exposed to temperatures in excess of

60°C (140°F)� DO NOT allow the hose to come in contact with

the hot surface of the barbecue body�

Keep cylinder upright: The cylinder must be housed

securely� It must remain upright at all times� It can be either

attached to a firm vertical wall by a cylinder bracket, or

stored on a firm level base�

Requirements for cylinder base: If the cylinder is to be

stored on a flat base, the base must be made from non-

combustible material� Soil or grass is not an appropriate

surface� Ensure there is adequate drainage, and that water

cannot collect around the cylinder�

Requirements for cylinder enclosure: Where the cylinder

is to be kept inside an enclosure, you must ensure there is

200 square centimetres of open ventilation at each of the top

and the bottom of the enclosure, for each cylinder stored in

it� This prevents leaking gas from building up in a confined

space� Gas vapour is highly explosive and can cause serious

bodily injury or damage to property if allowed to accumulate

in a confined space and ignited�

ventilation

The Barbecue Housing

We recommend that this installation be done in a masonry

structure and carried out by a professional tradesperson�

Other non-combustible material such as Hardiplank,

Villaboard with metal studs may also be used�

• Must have a minimum clearance from combustible

materials of all sides of the barbecue of 450 mm (18”)�

• This appliance must not be installed under or on

any combustible material� Minimum clearance from

combustible construction materials to all sides of the

appliance is 450mm (18”)�

Warning: Contact your local municipality for any building

codes regulating the installation of outdoor barbecue

appliances� Outdoor installations must conform to local

codes or, in the absence of local codes, with:

USA: National Fuel Gas Code, ANSI Z223�1/NFPA 54

CAN: B149�1 Natural Gas & Propane Installation Code

AUST: Australian Standards Code AS: 5601

as well as the requirements of any local council, gas,

electricity authority or other statutory regulation�

The Cavity

Your barbecue has been designed to sit into a cavity or

cutout rather than be placed directly onto a flat surface� It is

important that the dimensions of the cavity conform exactly

to those listed on page 21� This will ensure the barbecue sits

correctly in the cavity, and that the barbecue has sufficient

ventilation to operate efficiently and safely�

In creating the cavity, you should ensure that you have

convenient access to the gas connection point and

associated hardware:

• If the gas for your barbecue is supplied by a portable gas

bottle, you will need access to the gas connection point,

the gas hose and the gas cylinder at all times�

• If the gas for your barbecue is supplied by a fixed piped

gas supply (either natural gas or 45kg LPG cylinders),

you will need access to the gas connection point, the

piping and the shutoff valve�

Putting The Barbecue Into Place

Lower the barbecue onto the brickwork, but do not push

back into its final position - you will need to ensure you

can access the screws towards the front of the barbecue

side panel�

Attach the right and left side facia panels� The fixing

screws should already be in place at each side of the

barbecue frame�

Tighten the screws to

secure the facia panels�

Push the barbecue back

to its final position�

5ASSEMBLY OF MAIN BARBECUE

ASSEMBLY OF MAIN BARBECUE

Before You Start

Note the tools you will need before you begin�

Remove any protective plastic from stainless steel

components�

Check for damaged or missing parts, and consult your

retailer if necessary�

Attach The Side Shelves

(Trolley-Mount Models Only)

Attach the two top side shelves using the four screws

provided with each side shelf kit� You do not need any nuts,

as the screws go directly into threaded holes in the cart�

If you have an optional lower side shelf, attach it to the side

panel using 4 screws, washers and nuts�

Side Burner Parts

Assemble the side burner parts as shown�

The first burner disk should locate onto two notches on the

side burner (inside arrows)�

Also, the two notches on the bottom of the trivet line up with

the holes on the side burner (outside arrows)�

Fit The Heat Reﬂectors

The reflectors fit between each burner� They reflect heat

from the burners, upwards to the cooking surfaces�

The tabbed ends of the heat reflectors face forward to the

front of the barbecue frame� The tabs fit into the slots in the

front end of the barbecue behind the control panel�

The back of the reflectors rest on the rear of the barbecue

frame�

Allen Key

(provided)

Adjustable

spanner/

wrench

Phillips head

screwdriver

Top side shelf - use the

front holes, screws only

Lower side shelf - use the

side holes, screws, washers

and nuts�

6ASSEMBLY OF MAIN BARBECUE

Fit The Burners

Remove the ‘R’-shaped retaining clips from the burners�

Fit the burners, open end first, over the stem of the control

valves at the front of the barbecue� Lower the other end of

the burner so the lug locates into the corresponding hole at

the rear of the barbecue�

Replace the retaining clips into the burner lugs so the

burners stay in position�

Fit The Vaporizers

The Vaporizers are designed to vaporise fats and juices from

the meat� The Vaporizers reduce flare-ups and help to add

that great barbecue flavour� One Vaporizer is fitted over each

burner that is located under the grill�

The tabbed ends of the Vaporizers face forward to the front

of the barbecue frame� The tabs fit into the slots in the front

end of the barbecue behind the control panel� The Vaporizers

should be fitted to the same side of the barbecue as the

grate� They will not work if fitted under the plate�

Fit Cooking Plates And Grates

You should fit the plate to the left-hand side of the barbecue

frame (with the drain hole to the extreme left)� The grates are

fitted to the right hand side

of the barbecue frame� The temperature gauge on the

roasting hood has been calibrated for this arrangement of

plate and grate�

NOTE: The grates must always be positioned over the

Vaporizers�

The 5 burner model (4 main burners plus a side burner)

comes standard with a 320mm plate, a 320mm grill and a

160mm grill� You may use other combinations of cooking

surface, however, the plate may cover no more than 50% of

the total cooking area�

The 6 burner model (5 main burners plus a side burner)

comes standard with one third plate and two thirds grate and

is approved for use with a maximum of two thirds plate�

Do not cover the entire surface of the barbecue frame

with plates as this will cause severe heat damage to the

appliance�

ASSEMBLY OF MAIN BARBECUE

7ASSEMBLY OF MAIN BARBECUE

Fit The Warming Rack

The warming rack needs no screws� It sits on two notches on

the insides of the hood�

The Grease Tray (Built-In Models Only)

The grease tray of the inbuilt model slides along rails located

near the base of the barbecue frame� This is different to the

trolley mounted version, where the grease tray forms part of

the trolley�

Otherwise, the grease tray is exactly as portrayed in the

trolley mounted instructions� Newer models have a retaining

clip towards the rear of the barbecue to secure the grease

tray once it is pushed in�

ASSEMBLY OF MAIN BARBECUE ASSEMBLY OF OPTIONAL

ROTISSERIE

Assemble The Main Shaft

Assemble the shaft in the order shown�

Fit The Motor

First attach the motor mounting bracket to the roasting

hood�

Then slide the motor onto the bracket�

Fit The Shaft

The pointed

end goes into

the motor The collar rests on

the roasting hood�

Fit The Drawer Accessories

ASSEMBLY OF ACCESSORIES

A number of accessories are available for Trolley-Mount

models.

Fit The Baskets

The storage racks and condiment baskets can be fitted

directly, without the use of screws� Ensure they locate

properly into their respective holes�

Fit The Towel Rack

First, unscrew and remove the plastic end caps from the

towel rack� Then, using 2 flathead screws, washers and nuts,

attach the towel rack to the side panel� You may need to slide

the towel rails out of the way to access the screw holes�

Waste Bin

Ice Bucket

Paper Towel Holder

INSTALLATION INSTRUCTIONS

LPG/Propane Cylinder

If your barbecue is to be connected to a portable LPG

cylinder, you should position it in the far right drawer� Place

the prefitted mat down first, then position the cylinder on

top� Secure the cylinder by wrapping the strap around the

cylinder and clipping it to the bracket slots as shown in the

illustration�

Partial Enclosures (Australia Only)

This appliance shall only be used in an above ground, open

air situation with natural ventilation, without stagnant areas,

where gas leakage and products of combustion are rapidly

dispersed by wind and natural convection� Any enclosure

in which the appliance is used shall comply with one of the

following:

Within a partial enclosure that includes an

overhead cover and no more than two walls�

A common example is an outdoor gazebo�

Any enclosure with walls on all sides, but at

least one permanent opening at ground level,

and no overhead cover�

A common example is an enclosed back yard�

Typically, the walls are less than 3m high�

If they are higher, there is a danger of gas

build up�

The barbecue may be within a partial

enclosure that includes an overhead

cover and more than two walls, the

following shall apply:

• At least 25% of the total wall area

is completely open; and

• at least 30% of the remaining wall

area is open and unrestricted�

In the case of balconies, at least 20% of

the total of the side, back and front wall

areas shall be and remain open and

unrestricted�

10 INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Before You Begin

Check that the gas type is correct for your type of gas�

You will find the gas type label on the side of your barbecue�

If your barbecue is of the incorrect gas type, or if you are

unsure, consult your dealer before going any further�

This appliance must have a minimum clearance from

combustible materials of 450 mm (18”) on all sides of the

barbecue�

Do not install the appliance under or on any combustible

surface�

The appliance must be tested for safe and proper operation

on completion of installation�

Keep ventilation openings in the lower cabinet clear and

free of any debris� This barbecue is not approved for use on

marine craft�

NATURAL

GAS

REFER TO LOCAL

GAS AUTHORITY FOR CONFIRMATION OF GAS

UODNIFIEPYT TB

LPG

PROPANE

GAS

REFER TO LOCAL

GAS AUTHORITY FOR CONFIRMATION OF GAS

YT P FIE TBUODNI

Mobile Installation - Portable LP Gas/ Propane

Recommended minimum LPG/propane cylinder capacity

for use with this appliance is 4kg� Maximum LPG/propane

cylinder capacity for use with this appliance is 10kg� In the

USA, only a 20lb cylinder may be used�

Fit the regulator to the LPG/propane cylinder, as shown on

the right� Secure all joints spanner (wrench) tight but do not

over-tighten�

For POL cylinders, tighten anti-clockwise

For Quick Connect cylinders, tighten clockwise

Fixed Installation - Portable LP Gas/Propane.

BeefEater LPG/propane barbecues are designed to operate

at 2�75Kpa (11”WC)�

Connect the gas supply line to the barbecue inlet located on

the right side of the appliance using either hard plumbing,

or a flexible hose connected to a bayonet point, also known

as a quick connect fitting� Refer to AS 5601 or your local

installation code for pipe sizing details� Secure all joints

spanner (wrench) tight but do not over-tighten�

Test gas pressure by removing the last burner from the

left hand side of the barbecue and attaching a hose and

pressure gauge to the end of the gas valve� Turn on 2

burners and check the pressure� Inlet pressure should be

11�0” WC or 2�75 kPa�

Fixed Installation - Natural Gas

(Natural Gas installation should be carried out by a qualified

gas fitter)�

BeefEater Natural Gas barbecues are designed as low-

pressure appliances (4�0” WC, 1�00KPa)�

Fit the natural gas regulator supplied directly to the

barbecue inlet located on the right side of the appliance

using either hard plumbing, or a flexible hose connected to

a bayonet point, also known as a quick connect fitting� Refer

to AS 5601 or your local installation code for pipe sizing

details� Secure all joints spanner (wrench) tight but do not

over-tighten�

Test gas pressure by removing the last burner from the

left hand side of the barbecue and attaching a hose and

pressure gauge to the end of the gas valve� Turn on 2

burners and check the pressure� Inlet pressure should be

4�0” WC or 1�00 kPa�

Australia only (applies to all gas types) : Where a mobile

appliance is to be connected to a fixed gas supply via a

flexible hose connection, a retaining tether of adequate

strength shall be fixed to the appliance and be suitable to be

fixed to the wall within 50mm of each connection point� The

length of the tether shall not exceed 80% of the length of the

hose assembly� In this way, if the barbecue is accidentally

moved, the chain stops the barbecue from stretching the

hose� The barbecue appliance must be isolated from the

gas supply piping system by closing its manual shutoff valve

during any pressure testing of the gas supply piping system�

The barbecue appliance must be isolated from the gas

supply piping system by closing its manual shutoff valve

during any pressure testing of the gas supply piping system�

Converting the unit to natural gas

1� Turn off the gas supply valve on the gas cylinder� Ensure

that all gas controls on the BBQ are in the OFF position�

2� Disconnect the hose and regulator from the gas

cylinder and disconnect the gas hose from the barbecue

gas inlet using a 19mm open-ended spanner/wrench�

3� Open hood and remove all cooking plates, grills and

vaporisers from the BBQ�

4� Remove the ‘R’ shaped locking clips that hold each

burner in place and remove all burners from barbecue�

This needs to be done at the on the front firewall of

the BBQ�

5� The gas injector (also known as jets or nozzles) for each

burner are located within deep pockets at the on the

front firewall of the BBQ�

6� Remove each gas injector from the end of each jet

holder using a 6mm socket spanner/wrench, turning

gently in a counter clockwise direction� Be careful not

to block the orifice at the end of valve where the gas

injector is fitted and do not remove any of the thread

sealing compound from the orifice where the injector

is located�

7� Check the identification mark stamped on Hex Head

of the injector to confirm that it is the correct size

(NG: 2�10mm) Screw correct Jet back into place�

8� When fitting the NG gas injectors to the end of the jet

holder be sure to seat the injector correctly on the

thread before turning it in a clockwise direction until it

is seated firmly in place� Do not over-tighten�

Please note: for SL4000 side burners

One the side burner valve, from the inside bend the

pilot ignition tube out the way, unscrew the pilot jet

and replace with the 0�95mm NG jet supplied with the

conversion kit� Once done bend the tube back to the

original position� If necessary remove the chute before

changing the nozzle and then replace it when done�

INSTALLATION INSTRUCTIONS

Pilot Injector Bend

9� Replace all parts into position in the BBQ�

10� Refit the burners and secure with the locking clips that

hold each burner is position� Replace the vaporisers,

grills and cooking plates� Note: Check the operation

of each burner - on some models it may be necessary

to open the air-mixture screw (located at the burner

venturi) a couple of turns to get the correct flame�

11� Replace the LPG gas type label with the natural gas

label supplied�

12� Connect the natural gas hose and regulator (where

applicable) to the gas inlet on the barbecue� Tighten

firmly but do not over tighten� Connect gas regulator

to gas source line� Perform leak testing using same

procedure as for LPG on page 12�

13� For mobile units attach restraining tether to anchor

point on barbecue, and fasten within 50mm of fixed gas

outlet with suitable fastener� Ensure the length of the

tether does not exceed 80% of the length of the hose to

Aeration Screw Adjustment

12 INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Low

High

Low Off

the fixed gas supply outlet�

Turn down adjustment

• When converting to natural gas the turndown setting

will need to be adjusted to give a satisfactory flame on

low setting on each burner�

• Remove knob from valve shafts� For ignition valve the

low flame adjustment screw is located on the lower

right hand corner of the front of the valve body�

• Fully insert and rotate a flat bladed screwdriver to

adjust turndown�

• For non-igntion valves the screw is located inside the

knob spindle� Use a 2�5mm wide flat blade screwdriver

full inserted and make a 3/4 turn counter clockwise�

• After leak testing light one burner and set to high�

• One burner at a time turn the valve shaft to lowest

setting observe the flame to ensure a small steady

flame in achieved�

• Repeat for the other burners�

• Turn off burners and replace control knobs, ensuring

the knob is in the correct orientation when valve is in

“OFF” position�

Secure All Joints And Leak Test

Never use a naked flame to check for gas leaks. The gas

leak testing procedure should be conducted every time a

gas cylinder is refilled and reconnected to the appliance,

or after any new gas connection is made.

In a small container, mix up a solution of water and

detergent or soap� Mix the solution well�

For LPG/propane make sure that the gas supply valve on the

gas cylinder is turned on� For Natural Gas make sure that

the gas shutoff valve is on�

Make sure that the gas control valves on the appliance are

all turned off�

Using a brush or spray bottle apply the solution to the gas

line and each joint in the gas line�

Bubbling of the solution will indicate that there is a leak

present� Re-tighten or re-seal any joints that are leaking�

If a leak persists contact your distributor or the

manufacturer for assistance�

Check Proper Burner Operation

Following operating instructions, light each burner and

check for a clear blue flame with just a tip of yellow� Excess

yellow tipping can be adjusted using the burner adjustment

screw on the side of the burner� Turn the screw in an anti-

clockwise rotation to reduce the yellow�

Yellow tipping Right Wrong

Yellow tipping

Light blue

Dark blue

Light blue

13USING YOUR BARBECUE

USING YOUR BARBECUE

Before You Light The Barbecue

Perform the following checks

• Make sure all gas connections are tight and leak tested�

• Ensure the cooking surfaces are clean and hygienic�

• Check the control knobs are in the off position�

• Check that the gas supply is turned on�

• Ensure the hood of the barbecue and the lid of the side

burner are up� If you do not, gases can build up inside

the hood and create a dangerous situation�

• Make sure long handles do not hang over the edge of

the barbecue� Injury can result if they are accidentally

knocked�

Grease Tray

Neatly line the grease tray with a couple of sheets of

aluminium foil to aid in clean up� Cut the foil to shape and

make sure that the foil sits on the bottom of the tray�

Fill the tray with a 6mm (1/4”) layer of dry sand or other

non-combustible absorbent material to absorb grease�

Change the foil and absorbent material regularly to reduce

the likelihood of a grease tray fire

Lighting The Barbecue

The same procedure is used to light the main burners as

well as the side burner:

1� Push in and hold the control knob down while turning

slowly in an anti-clockwise direction until the starter

mechanism engages at the two o’clock position� At this

time the gas will start to flow�

2� Hold the control knob in while continuing to turn the

knob toward the High or twelve o’clock position�

3� The starter mechanism will click and the main burner

will now light� Continue turning the knob slowly until it

rests in the twelve o’clock position�

If the burner is alight, release the knob�

The requirement to press the knob in before turning

is a safety feature that prevents the knobs from being

accidentally turned on�

If the burner does not light

Keep the control knob pushed in and turn the control knob

in a clockwise direction to return to the OFF position� Wait

5 minutes for the gas to disperse and then repeat steps

1-3� If you cannot light the burners, call your retailer before

proceeding�

Manual lighting

Press and turn the left hand control knob anti-clockwise

to the High position, then use a long match to light the left

hand burner immediately through the gap between the front

of the grease tray and the barbecue body�

High

Low

O

High

Low

O

High

Low

O

Controlling The Burners

The control knob can now be turned to the desired heat

setting, Low, Medium or High� The control knob does not need

to be pushed in while selecting the heat setting�

To Turn Off The Burner

Push in and hold the control knob while turning in a clockwise

direction until the Off position is reached�

After Use

It is a good idea to leave the barbecue on for about 10 minutes

after you have finished cooking� This helps to burn away any

excess food residues and oil, and makes cleaning easier�

1� Be sure to turn off all control knobs and the cylinder valve

(for LPG/propane) or shut-off valve (for Natural Gas)�

2� Allow barbecue to cool�

3� Clean the drip tray and cooking surfaces�

4� Clean any food spills from the side burner�

5� Lower the hood and side burner lid�

Remove the gas cylinder from the enclosure before

disconnecting the gas line from the appliance� Tighten

all connections before placing the gas cylinder back in its

enclosure�

Off - Knob points

to right�

High - push in and

turn so knob

points

Low - continue

turning so knob

points to left

14 USING YOUR BARBECUE

USING YOUR BARBECUE

How Long Will The Gas In My Cylinder Last?

If you have a full cylinder of propane, just look at the table

below to see how many hours of gas you have, depending

on how many burners you have alight� These figures are

approximate only�

You may notice that if you have several burners alight and

your cylinder becomes low on gas, the liquid may freeze up�

If this occurs, turn the cylinder and all burners off and wait

till the liquid thaws� You may then reignite the burners�

9KG/20LB BOTTLE 4KG/9LB BOTTLE

High HighLow Low

1 burner 25 hours 75 hours 11 hours 33 hours

2 burner 12�5 hours 37�5 hours 5�5 hours 17 hours

3 burners 8�3 hours 25 hours 3�7 hours 11 hours

4 burners 6�3 hours 19 hours 2�75 hours 8 hours

5 burners 5 hours 15 hours 2�25 hours 6�6 hours

These tables were worked out using the following:

• Each burner on high setting uses 19 MJ/hour or 18,000

BTU/hour

• Each burner on low setting uses 6 MJ/hour or 5,700

BTU/hr

• Each kg of gas contains 50MJ� Each lb of gas contains

21,600 BTU

Produktspezifikationen

Marke:	BeefEater
Kategorie:	Grill
Modell:	Signature BS12850

Brauchst du Hilfe?

Wenn Sie Hilfe mit BeefEater Signature BS12850 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Grill BeefEater

BeefEater Signature BOK56WG Bedienungsanleitung

6 September 2024

BeefEater S26010 Bedienungsanleitung

6 September 2024

BeefEater BS26410 Bedienungsanleitung

6 September 2024

BeefEater Signature BOK44WG Bedienungsanleitung

6 September 2024

BeefEater BSW318SA Bedienungsanleitung

6 September 2024

BeefEater Signature BOK53WG Bedienungsanleitung

6 September 2024

BeefEater Proline BOKP60WG Bedienungsanleitung

6 September 2024

BeefEater 1500 Series BDB1540GA Bedienungsanleitung

6 September 2024

BeefEater Discovery 1100S Bedienungsanleitung

6 September 2024

BeefEater Discovery 1100E Bedienungsanleitung

6 September 2024

Bedienungsanleitung Grill

Neueste Bedienungsanleitung für -Kategorien-

Fisher & Paykel BGC30-BQ-L Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BH1-48R-N Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BH1-48RS-L Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BH1-30R-L Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BE1-48RC-L Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BE1-36RC-N Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BE1-36RC-L Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BE1-48RC-N Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BH1-36R-N Bedienungsanleitung

3 Dezember 2024

Fisher & Paykel BH1-30R-N Bedienungsanleitung

3 Dezember 2024