AV:link M8S Bedienungsanleitung

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr AV:link M8S (4 Seiten) in der Kategorie Subwoofer. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
M8S
ACTIVE SUBWOOFER 8”
Order ref: 170.190UK
User Manual
Version 1.1
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
170.190 User Manual UK
Introduction
Thank you for choosing the AV Link M8S active subwoofer as part of your sound system. This product is designed with
flexibility and reliability in mind to offer long-lasting, high quality output for many varied applications. Please read this
manual fully and follow the instructions to achieve the best results with your new purchase and to avoid damage through
misuse.
Warning
To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.
If liquids are spilled on the cabinet, stop using immediately, allow unit to dry out and have checked by qualified personnel
before further use. Avoid impact, stress or extreme pressure to the cabinet
No user serviceable parts inside Do not open the panel refer all servicing to qualified service personnel – –
Safety
• Check for correct mains voltage and condition of Fig.8 lead before connecting to power outlet
• Ensure speaker wires and/or signal leads are in good condition with no shorts or damaged plugs
• Do not allow any foreign objects to enter the case or through the ventilation grilles
Placement
• Keep out of direct sunlight and away from heat sources
• Avoid damp or dusty environments
• Position on a level, stable surface, ideally against a wall or in a corner
• Avoid sharp objects protruding through the front grille cloth or speaker cone
• Ensure adequate access to controls and connections
Cleaning
• Use a soft dry or slightly damp cloth to clean the cabinet as required
• Use a vacuum cleaner to clear the rear heat-sink of any dust or debris build-ups
• Do not use strong solvents for cleaning the unit
Amplifier Panel
1. Amplifier “HI LEVEL” inputs
Connect and wires tween + - be
amplifier L+R outputs and speakers
2. RCA L+R LINE IN
L+R inputs for line level audio signal
3. POWER LED
Indicates mains power on
4. FREQ control
Adjust cutoff frequency of crossover
5. VOLUME level control
Adjust overall output of subwoofer
6. Mains fuse holder
Replace only with approved type
7. Fig.8 Mains inlet
Connect supplied mains lead here
8. Power switch
Switches mains power ON/OFF
9. AUTO ON/ON
Select “Auto on” or “Always on”
170.190 User Manual UK
Connection
Connect the M8S to the mains using the mains lead supplied or an equivalent, good quality fig.8 mains lead.
Ensure that the mains voltage is as stated on the rear panel and the outlet has sufficient capacity to operate the sub.
Determine how the sub unit is to be configured. If already operating a stereo amplifier with 2 speakers, the M8S can be
configured to “tap off” a signal from the amplifier output without affecting the power output of the left and right
speakers.
Simply connecting the Left and Right amplifier outputs to the “AMPLIFIER HI LEVEL IN” terminals on the M8S and then
from these terminals onto the left and right speakers effectively connects the M8S between the amplifier and speakers,
which can simplify wiring, removing the need for a separate signal lead to the sub unit.
Alternatively, if a separate line level audio signal is available, connecting left and right RCA cables to the “LINE IN”
connectors is preferred (left and right signals are fed independently to the speaker and are not electrically summed)
With the VOLUME control turned fully down, switch on the power on the rear panel Once powered up, gradually turn the .
VOLUME up part way and play a signal through the system. Increase VOLUME as required to balance with top speakers.
Rotating the FREQ control will vary the cutoff frequency of the internal active crossover circuit. The ideal setting depends
upon the program material, types of top speakers used and personal preference. Lower settings may require higher
VOLUME adjustment to compensate for the extra frequencies that are removed from the signal.
Take care not to drive the sub unit too hard (usually denoted by a “knocking” or “flapping” noise from the speaker cone).
Sub bass is difficult to hear over full range speakers and should be almost imperceptible in operation, simply adding
warmth and fullness to the sound.
At the lower right- hand side of the rear panel is a selector switch marked “AUTO ON – ON”
Selecting AUTO ON puts the M8S into an energy saving standby mode when no signal is present and automatically
switches power to the amplifier when a signal is detected.
Selecting ON keeps the amplifier powered up constantly.
The front grille frame is removable for studio monitor applications or where the speaker cone may not need protecting.
Before powering down, turn the channel gain controls fully down to avoid loud noises when switching off.
Specifications
M8S Subwoofer
Power supply
220 - 250Vac, 50/60Hz, Fig.8
Driver
20cm (8“) reinforced cone
Connections
Speaker level input terminals, RCA line level in
Cutoff frequency
45 - 150Hz
Rated output power
100W
Peak output
200W
Frequency response
50 - 250Hz
Dimensions
300 x 330 x 300mm
Weight
7.44kg

Produktspezifikationen

Marke: AV:link
Kategorie: Subwoofer
Modell: M8S

Brauchst du Hilfe?

Wenn Sie Hilfe mit AV:link M8S benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Subwoofer AV:link

Bedienungsanleitung Subwoofer

Neueste Bedienungsanleitung fĂĽr -Kategorien-