Audiovox AS9233ST Bedienungsanleitung

Audiovox Sicherheit AS9233ST

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Audiovox AS9233ST (8 Seiten) in der Kategorie Sicherheit. Dieser Bedienungsanleitung war fĂĽr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/8
128-8604
1 of 8
Remote Start Alarm Keyless Entry
Upgrade System
Congratulations on your purchase of this automotive Remote Start / Alarm Keyless Entry
Upgrade System. This system is a state - of - the - art system is designed to arm and disarm
when it receives a lock or unlock command from your existing Factory Keyless Entry
Transmitter. Taking a few moments to read this manual will help to ensure that your vehicle
is protected at all times.
NOTE:
The system has the ability to beep the vehicle's horn, sound a siren, or both. Where a beep
or chirp is mentioned, consider either or both may sound.
Also All functions of the system will be controlled by the factory transmitter, including the start
sequence however for optimum range, it is suggested that the one button transmitter supplied
be used for starting, and unlocking while running under control of the the remote start.
ARMING THE SYSTEM: ( ACTIVE )
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. Press and release the Lock button on the keychain transmitter.
3. The siren and or horn will beep one time, the parking lamps will flash one time,
and the LED found on the glass mounted receiver will begin to slowly flash, indicating that
the system is ARMED.
If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
Simply close the opened entry point to provide full protection. If the siren "chirped"
three times, sometime after arming, the exclusive delayed dome light learn circuit
has been programmed and the system detected a open entry point after the
learned delay expired. Again, closing the hood, trunk, or doors will correct the
problem and you do not need to disarm the system to make the correction. If the
siren/horn did not sound when arming, then the chirps have been turned off, and
you should refer to the section titled “ ELIMINATING THE ARM / DISARM CHIRPS “
in this manual.
4. Any time the door lock switch in the vehicle is used to lock the doors while
the ignition key is turned off, the system will immediately arm. To lock the doors
after entering the vehicle, make sure the ignition key is switched on first.
Turning the ignition key on first will stop the system from arming.
ARMING THE SYSTEM: ( PASSIVE )
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. The LED will begin to flash rapidly, indicating that the system
is automatically ( passively ) arming. As an added convenience, the 30
second automatic passive arming will not begin until all doors are closed,
allowing passengers to exit the vehicle at their convenience.
3. In 30 seconds, you will hear a single short chip from the siren, and the vehicle’s
parking lamps will flash one time, indicating that the system has ARMED. At
this time, the dash mounted PRLED will begin to flash slowly, providing a
visualindication that the system is fully armed.
4. It is possible to program the system, that when the alarm is allowed to
automatically passive arm, there will be a 15 second delay after a door is
opened before the alarm will sound. However, if the system is programmed
for instant trigger there will be no delay. Check with your installer for the setting
of this feature.
Model AS9233ST
OWNER’S MANUAL
128-8604
2 of 8
Page 2
IMPORTANT! When the system is programmed for passive arming, the system
will always arm, even when the keychain transmitter has not been used to
lock the doors.
When you leave the vehicle, and a door has been left opened, the system will arm
after 10 minutes. If you plan to vacuum the car, or if service work is being
performed, either leave the key in the ignition and switched to the on position,
or put the system into valet mode. If you do not do this, the system will arm in
10 minutes, and you may inadvertently trip the alarm.
PROTECTION WHILE THE SYSTEM IS ARMED :
1. Opening any door, hood, or trunk will cause the alarm to immediately sound.
The alarm will continue to sound for 30 seconds, then stop and
automatically rearm the vehicle. If the potential thief left a door opened, the
alarm will sound for three more 30 second cycles, then re - arm and ignore the
opened door zone.
2. Whenever the system is armed, the on glass receiver's LED indicator will
slowly flash. This serves as a visual deterrent to the potential thief. The LED
is a very low current bulb, and will not cause the vehicle’s battery to drain, even
when the vehicle is left unattended for extended periods.
3. Whenever the system is triggered, the vehicle’s parking lights will flash for the
30 second alarm cycle, attracting added visual attention to the vehicle.
4. Whenever the system is armed, the vehicle’s starter will be disabled. The
vehicle will not start.
DISARMING THE SYSTEM :
1. As you approach the vehicle, press and release the unlock button on the
keychain transmitter.
2. The siren and or horn will beep two times, the parking lamps will flash two
times,and the on glass receiver's LED will turn off, indicating that the
system is DISARMED. If the optional entry illumination feature has been
installed, the vehicle’s interior lights will turn on for 30 seconds, or until the
ignition key is turned on.
NOTE: If your system has been programmed for “ passive arming “, then it will
begin to re-arm immediately after disarming. This is indicated by a
rapid flashing of the on glass receiver's LED. Opening one of the
vehicle’s doors will suspend the passive arming process until all doors
have been closed, or until the ignition key has been turned on.
INTRUSION WARNING SIGNALS :
The system will inform you if an intrusion attempt has occurred while you were away from
the vehicle. If an intrusion attempt has occurred, the siren and or horn will beep four times
when the system is disarmed. The vehicle’s parking lights will also flash three times to indicate
an intrusion has occurred.
Enter the vehicle and observe the on glass receiver's LED for further information.
1. If the LED is flashing one time...pause...one time...pause...etc., then an
intrusion attempt was made to a voltage sensing, light activated entry point, or
to an optional sensor that has been connected to zone 1.
2. If the LED is flashing two times...pause...two times...pause...etc., then an
intrusion attempt was made to the hood or trunk, or to an optional sensor that
has been connected to zone 2.
3. If the PRLED is flashing three times...pause...three times...pause...etc., then an
intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory, and will only be erased
when the ignition key is turned to the “ on “ position.
OPERATING THE EMERGENCY PANIC:
The buttons on your keychain transmitter will allow you to immediately activate the alarm in
emergency situations. To use the remote panic switch;
1. Press the unlock, then lock, then unlock buttons on your keychain transmitter
128-8604
3 of 8
within3 seconds. The alarm will immediately sound, and continue to sound for
30 seconds.
2. To stop the alarm before the 30 second cycle has expired, simply press
and release the unlock button on your keychain transmitter.
NOTE: If the factory system has a panic mode, it is suggested that the factory panic feature
be used instead of the PRO9233ST to prevent any potiential problem of turning off the panic
mode.
USING THE VALET SWITCH :
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need
to hand your transmitter to parking attendants or garage mechanics. When the system is in
valet mode, all alarm functions are bypassed, however the remote panic feature and
remote door locks will remain operational. To use the valet mode, the system must first be
disarmed either by using your keychain transmitter, or by overriding the system as
explained in the Manual Override Section of this manual.
TO ENTER THE VALET MODE:
1. Disarm the unit by use of the factory transmitter or by use of the manual override
sequence.
2. Turn the ignition switch to the “On” position.
3. Press and hold the pushbutton switch found on the glass mounted receiver assembly
for 5 seconds, until the LED turns on, indicating valet mode has been successfully
entered.
TO EXIT VALET:
With the ignition switch in the on position, press and release the pushbutton switch one time
. The LED turns off indicating the valet mode has successfully been exited.
MANUALLY OVERRIDING YOUR SYSTEM:
USING SIMPLE VALET SWITCH MANUAL OVERRIDE
If your factory transmitter is lost, broken, or otherwise rendered inoperable your Security
System can be disarmed without the use of the keychain transmitter. This is necessary,
since you will need the ability to operate your vehicle if the transmitter is lost or its battery
fails. If your system has been selected for Valet Switch manual override as indicated on the
last page of this manual, to override the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the on position.
3. Within 5 seconds, press and hold the valet pushbutton switch found on the glass
mounted receiver.
The alarm system will stop sounding and enter the (bypassed) mode. You can now start
and operate the vehicle normally.
Typically this override mode is used only if the transmitter has become inoperative.
USING CUSTOM CODE MANUAL OVERRIDE:
If your factory transmitter is lost, broken, or otherwise rendered inoperable, your system
can be overridden allowing operation of the vehicle. The manual override code is pre-
programmed at the factory to 11. This code can be changed by the operator to a more
familiar two digit number. Once you’ve become familiar with the system’s operation and
override procedure, we suggest you change the code for added security.
NOTE: The override procedure below describes use, assuming that the factory
preset code has not been changed and is still set to the factory default 11.
The on glass receiver's LED valet/override push button switch is used to enter the
tenths and units digits, pressing and releasing this button one time for each
digit required.
If your system has been selected for Custom Code manual override as indicated on the last
page of this manual, to bypass the alarm system; with a code of 11, follow the sequence
listed below:
1. The LED is flashing indicating the unit is armed, enter the vehicle, the siren
will sound, turn the ignition switch to the “on” position.
Page 3

Produktspezifikationen

Marke: Audiovox
Kategorie: Sicherheit
Modell: AS9233ST

Brauchst du Hilfe?

Wenn Sie Hilfe mit Audiovox AS9233ST benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Sicherheit Audiovox

Audiovox

Audiovox AS9233ST Bedienungsanleitung

23 August 2024
Audiovox

Audiovox Prestige Platinum APS 686T Bedienungsanleitung

22 August 2024
Audiovox

Audiovox APS-45 Bedienungsanleitung

22 August 2024
Audiovox

Audiovox PRO-9056TW Pursuit Series Bedienungsanleitung

22 August 2024
Audiovox

Audiovox APS 675 Prestige Platinum Bedienungsanleitung

22 August 2024

Bedienungsanleitung Sicherheit

Neueste Bedienungsanleitung fĂĽr -Kategorien-

NetworX

NetworX NX-595E IP Communication Module Bedienungsanleitung

5 Oktober 2024
Unitron

Unitron Smart Alert Systeem Bedienungsanleitung

24 September 2024
NetworX

NetworX NX-408 Bedienungsanleitung

20 September 2024
Theben

Theben Luxa 102.150 - 1020961-2 Bedienungsanleitung

19 September 2024
Elro

Elro AB600P - MOTION DETECTOR Bedienungsanleitung

17 September 2024
Elro

Elro AG40KE Bedienungsanleitung

17 September 2024
Elro

Elro CS95DVR Bedienungsanleitung

16 September 2024
BTicino

BTicino Classe100 X16E Beveiliging Bedienungsanleitung

16 September 2024
One2track

One2track Safety Angel Bedienungsanleitung

27 August 2024
Sygonix

Sygonix SY-3851632 Bedienungsanleitung

27 August 2024