AudioSource AMP 100 Bedienungsanleitung
AudioSource
Receiver
AMP 100
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AudioSource AMP 100 (4 Seiten) in der Kategorie Receiver. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
OWNER’S MANUAL
AMP 100
AudioSource®
13970 SW 72nd Ave
Portland, OR 97223
503.914.4688
www.audiosource.net AMP 100 Owner’s Manual
Congratulations on your purchase of the AudioSource® AMP 100.
Please take a few moments to read this entire manual, and be sure to
retain this document for future reference. Please read and observe all
safety instructions detailed on page 2.
NOTE: If any part of this product is damaged or missing, please call your
dealer or AudioSource® directly at 1.877.715.5439 or 503.914.4688.
Please read your warranty and retain your receipt and original carton
for possible future use.
For more information about AudioSource® electronics, speakers and
accessories please visit www.audiosource.net
AMP 100
Home Audio Multi-Zone Stereo Power Amplifier
FEATURES:
Line 1 / Line 2 priority input switching
Line 2 auxiliary output
Speaker A/B switching
Front panel Balance and Volume controls
Signal sensing “Power On”
SPECIFICATIONS
Stereo (8 ohm): 50W per channel, 20Hz ~ 20kHz, <1% THD+N
60W per channel, 1kHz, <1% THD+N
Stereo (4 ohm): 60W per channel, 20Hz ~ 20kHz, <1% THD+N
75W per channel, 1kHz, <1% THD+N
Bridged Mono (8 ohm): 160W, 1kHz, <1% THD+N
Frequency Response: 10Hz ~ 30kHz, +0dB/ -3dB
Signal to Noise Ratio: 100dBA below 50W output into 8 ohms
Channel Separation: 65dB @ 1kHz, referred to 50W output
into 8 ohms
Input Sensitivity: 900mV input for rated 50W output
into 8 ohms
AC Power Consumption: 500W maximum
Net Weight: 9.6lbs / 4.4kgs
Gross Weight: 10.8lbs / 4.9kgs
2.9”
(74mm)
16.5” (419mm)
9.5”
(242mm)
Left Right
Balanc e Volume
SPEAKERS
A B
AMP 100
STEREO POWER AMPLIFIER
Min Max
POWER
AMP 100
OWNER’S MANUAL
13970 SW 72nd Ave. Portland, OR 97223 • 503.914.4688 • www.audiosource.net
2
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO
USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL!
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. The ventilation should not be impeded
by covering the ventilation openings with items such as newspaper, table-
cloths, curtains etc. Install in accordance with the manufacturer’s instructions.
8. Do not install near heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat. No open flame
sources, such as lighted candles, should be placed on the apparatus.
9. Do not defeat the safety purpose of the polarized or grounding type plug.
A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
MAGNETIC FIELD: !!CAUTION!! Do not locate sensitive high-gain equipment such as preamplifiers or tape decks directly above or below the unit. Because
this amplifier has a high power density, it has a strong magnetic field, which can induce hum into unshielded devices that are located nearby. The field is
strongest just above and below the unit. If an equipment rack is used, we recommend locating the amplifier(s) in the bottom of the rack and the preamplifier
or other sensitive equipment at the top.
EXPLANATION OF
SAFETY SYMBOLS
The exclamation point within an equilateral triangle is intended to alert the user of the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the products’ enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
10. Protect the power cord from being walked on or pinched particularly at the
plugs, convenience receptacles, and at the point of exit from the apparatus.
11. Unplug the apparatus during lightning storms or when unused for long
periods of time.
12. Refer all servicing to qualified personnel. Servicing is required when the
apparatus has been damaged in any way, such as when the power supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
13. The apparatus should be connected to a mains socket outlet with a protective
earthing connection.
• WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE APPARATUS SHALL NOT
BE EXPOSED TO DRIPPING OR SPLASHING AND THAT OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL NOT BE PLACED
ON APPARATUS.
• WARNING: TO PREVENT FIRE OF SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
• WARNING: THE MAINS PLUG IS USED AS DISCONNECT DEVICE. THE DISCONNECT DEVICE SHALL REMAIN READILY AVAILABLE.
• WARNING: ONLY USE ATTACHMENTS OR ACCESSORIES SPECIFIED OR PROVIDED BY THE MANUFACTURER.
AMP 100
OWNER’S MANUAL
13970 SW 72nd Ave. Portland, OR 97223 • 503.914.4688 • www.audiosource.net 3
1. Power Switch
Switches the AMP100 on or off. A red LED indicates connection to AC power
while in standby mode. Turns green indicating audio signal is present.
2. Speaker Selector
Selects speaker zone A or B. For A + B zones push both buttons in.
3. Balance
Fades speaker output between the Right and Left Channels
4. Volume
Adjusts amplifier volume.
FRONT PANEL CONTROLS
6. Line 1 Input
This is the secondary input, use Line 2 IN for your main input. Line 1 IN can
be used if a second source is desired and takes over when signal is present
and has at least a 5mV level. When there is no signal, or a signal with less
than 5mV level, the amp switches back to Line 2 IN after a brief delay.
7.
8.
Line 2 Input/Output
9.
10.
Mode Select Switch
Switches the amplifier from Stereo mode to Bridged mode.
11.
13.
AUTO ON Select Switch
Power can be turned on and off manually via the switch on the front panel
or automatically by signal sensing. Set it to NORMAL for manual power on/off.
Set to AUTO for signal sensing; the amp will turn on when audio signal is
detected at the inputs. NOTE: The front panel power switch must be in the
ON position (pushed in) for the AUTO ON feature to operate.
Speaker Zone A Output
Speaker output terminals for zone A. Minimum impedance: 8 ohm bridged
or 4 ohm stereo.
Speaker Zone B Output
Speaker output terminals for zone B. Minimum impedance: 8 ohm bridged
or 4 ohm stereo.
Power Cord & Fuse Holder
This amplifier is configured for operation at 115V. (North America) A fuse
in the integrated holder provides safety protection from fault conditions.
Replace fuse with 5 x 20mm T4A 250V.
REAR PANEL CONTROLS
Figure 1. Front Panel
Left Right
Balance Volume
SPEAKERS
A B
AMP 100
STEREO POWER AMPLIFIER
43
21
Min Max
POWER
12. Unswitched A/C Terminal
Provides A/C power for additional components. Use only for a single low
power device such as a tuner, CD, DVD, turnable or other non-amplified
electronics. Do not connect another amplifier or receiver. Ensure 400W
max power consumption for any device plugged in here.
6
8
9 11 13
Figure 2. Rear Panel
7
10
RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN
CAUTION NORMAL AUTO
AUTO ON
MODEL AMP100
POWER CONSUMPTION
500W/117 VAC-60Hz
RIGHT LEFT
( )-
(+) Bridging
IN
Line 1
Serial Number:
IN OUT
Line 2 Line 2
WARNING:
TO PREVENT ELECTRICAL
SHOCK DO NOT REMOVE
THE COVER. NO USER
SERVICABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED PERSONNEL.
INPUT
STEREO BRIDGED
MODE
(+) (+)( )-
UNSWITCHED
400W MAX
117 VAC-60Hz
CLASS 2 WIRING
FUSE 4A
Connect
Receiver
Here
12
Line 2 IN should be used as the “primary” or main input for the amplifier.
Connect your receiver or main source to this input. Use Line 2 OUT to pass
Line 2 IN signal to another amplifier.
If you will be connecting one or two pair of speakers to the amplifier, place
the switch in the “Stereo” position. NOTE: For playing 2 pairs of speakers
(A plus B), make sure each speaker has an impedance of 8 ohms or greater.
When set to “Bridged” mode, the amplifier is a single channel mono amplifier.
To play separate Right and Left channel signals with a pair of mono amplifiers,
connect to the source using the Right (red) RCA jacks at Line 2 IN. Connect
the Left RCA cable end to one amp, and the Right RCA cable to the other.
Set both MODE switches to BRIDGED, and follow the instructions for bridged
speaker connection.
NOTE:The AMP 100 supplies 150W in bridged mode, Please verify that your
speakers are capable of handling such power to avoid possible damage!
For stereo output connect the speaker’s positive (red) terminal to the amplifier’s
positive (red) terminal, and the speaker’s negative (black) terminal to the
amplifier’s negative (black) terminal for each Right and Left speaker.
NOTE: To prevent sonic degradation in your speaker installation, total speaker
wire resistance should be kept below 0.5 ohms. This table lists recommended
speaker wire gauge versus wire run length.
Place the “MODE” switch in the “BRIDGED” position and use both red
terminals to connect to the speaker. Connect the speaker’s negative (black)
terminal to the amplifier’s left channel positive (red) terminal, and the speaker’s
positive (red) terminal to the amplifier’s right channel positive (red) terminal.
NOTE: Only one zone (A or B) can be bridged. Do not attempt to bridge both
A and B speaker terminals! This may result in a lower impedance than the
amplifier is designed for and may damage your amplifier. The minimum
impedance for the total load connected in bridged mode is 8 ohms.
STEREO MODE
BRIDGED MODE
BRIDGED MODE- STEREO SOUND USING TWO MONO AMP 100
BRIDGED MODE- MONO APPLICATION
For bridged mode, playing Right and Left together as mono output, use a
Y cable adapter to connect Right and Left RCA signal to the Right (red) input
at Line 2 IN. Set the MODE switch to BRIDGED and follow the instructions
for bridged speaker connection in the SPEAKER TERMINALS section of
this manual.
50’ or less - 16 Gauge 2-Cond. CL3 Rated
50’ - 150’ - 12 Gauge 2-Cond. CL3 Rated
150’ - 200’ - 10 Gauge 2-Cond. CL3 Rated
SPEAKER TERMINALS - STEREO MODE
SPEAKER TERMINALS - BRIDGED MODE
Produktspezifikationen
Marke: | AudioSource |
Kategorie: | Receiver |
Modell: | AMP 100 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit AudioSource AMP 100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Receiver AudioSource
31 August 2024
Bedienungsanleitung Receiver
- Receiver Asus
- Receiver Hama
- Receiver Audio-Technica
- Receiver Logitech
- Receiver Manhattan
- Receiver Nedis
- Receiver Philips
- Receiver Sandberg
- Receiver Sony
- Receiver Roland
- Receiver MX Onda
- Receiver Bosch
- Receiver Vox
- Receiver TechniSat
- Receiver Yamaha
- Receiver Velleman
- Receiver CSL
- Receiver Alecto
- Receiver Denver
- Receiver EMOS
- Receiver König
- Receiver MarQuant
- Receiver Renkforce
- Receiver Bush
- Receiver Thomson
- Receiver Blaupunkt
- Receiver Kenwood
- Receiver Sharp
- Receiver Hilti
- Receiver Pyle
- Receiver Golden Age Project
- Receiver Aiwa
- Receiver AKG
- Receiver Auna
- Receiver Bose
- Receiver Bowers And Wilkins
- Receiver Caliber
- Receiver Denon
- Receiver Pioneer
- Receiver JBL
- Receiver JVC
- Receiver Klipsch
- Receiver Motorola
- Receiver Onkyo
- Receiver Sennheiser
- Receiver Shure
- Receiver Technics
- Receiver Vivanco
- Receiver Hifonics
- Receiver Megasat
- Receiver Smartwares
- Receiver Akai
- Receiver Dual
- Receiver Ferguson
- Receiver Strong
- Receiver Tascam
- Receiver Zoom
- Receiver Garmin
- Receiver Nexa
- Receiver Goobay
- Receiver Lindy
- Receiver Plantronics
- Receiver Fenton
- Receiver TOA
- Receiver Rotel
- Receiver Musway
- Receiver Tripp Lite
- Receiver Audio Pro
- Receiver Cabasse
- Receiver Harman Kardon
- Receiver Magnat
- Receiver Marmitek
- Receiver Marshall
- Receiver Naim
- Receiver Power Dynamics
- Receiver Samson
- Receiver Scosche
- Receiver Skytec
- Receiver Vonyx
- Receiver Peavey
- Receiver Marshall Electronics
- Receiver Sagem
- Receiver Simrad
- Receiver AVM
- Receiver Xoro
- Receiver Karma
- Receiver Reely
- Receiver Edision
- Receiver GigaBlue
- Receiver Humax
- Receiver Kathrein
- Receiver Metronic
- Receiver Xtrend
- Receiver Icom
- Receiver Alpine
- Receiver Rupert Neve Designs
- Receiver NAD
- Receiver Fender
- Receiver Renegade
- Receiver Ebode
- Receiver Vincent
- Receiver Vision
- Receiver Behringer
- Receiver Mackie
- Receiver Omnitronic
- Receiver MB Quart
- Receiver Marantz
- Receiver Monoprice
- Receiver Arcam
- Receiver Cambridge
- Receiver Crown
- Receiver Dynacord
- Receiver Ecler
- Receiver Luxman
- Receiver Monacor
- Receiver TEAC
- Receiver Thorens
- Receiver Crunch
- Receiver Chamberlain
- Receiver JUNG
- Receiver Aplic
- Receiver InLine
- Receiver Sangean
- Receiver Classé
- Receiver Optex
- Receiver Sherwood
- Receiver Jamo
- Receiver AXTON
- Receiver Clarion
- Receiver Mac Audio
- Receiver Kogan
- Receiver Humantechnik
- Receiver Skytronic
- Receiver Yaesu
- Receiver Audizio
- Receiver ESX
- Receiver Reloop
- Receiver Pinnacle
- Receiver Block
- Receiver Rega
- Receiver SYNQ
- Receiver Insignia
- Receiver DataVideo
- Receiver RCF
- Receiver Electro-Voice
- Receiver Cyrus
- Receiver Scansonic
- Receiver Sogo
- Receiver Delta Dore
- Receiver Salus
- Receiver Yorkville
- Receiver Elektrobock
- Receiver FiiO
- Receiver Boss
- Receiver IFM
- Receiver American Audio
- Receiver Anthem
- Receiver Roksan
- Receiver Engel Axil
- Receiver Alto
- Receiver Kopul
- Receiver Chord
- Receiver Kramer
- Receiver Hertz
- Receiver Pro-Ject
- Receiver Aeon Labs
- Receiver Vaddio
- Receiver Galaxy Audio
- Receiver HQ Power
- Receiver Ibiza Sound
- Receiver Kicker
- Receiver Warm Audio
- Receiver Polk
- Receiver Line 6
- Receiver Bogen
- Receiver DBX
- Receiver McIntosh
- Receiver Sonance
- Receiver Jensen
- Receiver JL Audio
- Receiver Pyle Pro
- Receiver PreSonus
- Receiver Qtx
- Receiver Hartke
- Receiver ART
- Receiver Deaf Bonce
- Receiver Fredenstein
- Receiver LD Systems
- Receiver RDL
- Receiver Audiolab
- Receiver Summit Audio
- Receiver Black Lion Audio
- Receiver Bluesound
- Receiver GlobalSat
- Receiver Chandler
- Receiver DAP
- Receiver DAP Audio
- Receiver Denson
- Receiver DLS
- Receiver Focal
- Receiver Focusrite
- Receiver Formuler
- Receiver Fusion
- Receiver Graupner
- Receiver Ground Zero
- Receiver Helix
- Receiver Homecast
- Receiver Infinity
- Receiver JB Systems
- Receiver Koda
- Receiver Lanzar
- Receiver Legamaster
- Receiver Mercury
- Receiver Monitor Audio
- Receiver Mtx Audio
- Receiver Phoenix Gold
- Receiver REL Acoustics
- Receiver Selfsat
- Receiver Soundstream
- Receiver Steren
- Receiver Sunstech
- Receiver Terratec
- Receiver AMX
- Receiver Triax
- Receiver Velodyne
- Receiver Wharfedale
- Receiver Phonic
- Receiver Adastra
- Receiver Siig
- Receiver Amiko
- Receiver Mooer
- Receiver AudioControl
- Receiver TV One
- Receiver StarTech.com
- Receiver Blackstar
- Receiver Smart-AVI
- Receiver QSC
- Receiver Dahua Technology
- Receiver Proel
- Receiver Niles
- Receiver Martin Logan
- Receiver Sound Devices
- Receiver Speco Technologies
- Receiver IFi Audio
- Receiver Gefen
- Receiver Polsen
- Receiver Russound
- Receiver Vocopro
- Receiver SRS
- Receiver Astell&Kern
- Receiver IMG Stage Line
- Receiver Inovonics
- Receiver Mosconi
- Receiver Atlas Sound
- Receiver FBT
- Receiver CYP
- Receiver Amplicom
- Receiver Ampeg
- Receiver Avalon
- Receiver Bang Olufsen
- Receiver Lectrosonics
- Receiver ATen
- Receiver Eventide
- Receiver Laney
- Receiver SVS
- Receiver Citronic
- Receiver Crest Audio
- Receiver Lab Gruppen
- Receiver SPL
- Receiver Parasound
- Receiver MEE Audio
- Receiver Wet Sounds
- Receiver Pyramid
- Receiver Stewart
- Receiver Black Hydra
- Receiver Linn
- Receiver Roswell
- Receiver Music Hall
- Receiver Audac
- Receiver OSD Audio
- Receiver Match
- Receiver Neets
- Receiver EA
- Receiver BZBGear
- Receiver Crestron
- Receiver HiFi ROSE
- Receiver Accell
- Receiver Ibanez
- Receiver Antelope Audio
- Receiver Pharos
- Receiver Kemo
- Receiver Avantree
- Receiver PSB
- Receiver Extron
- Receiver Comtek
- Receiver Ashdown Engineering
- Receiver Ram Audio
- Receiver Esoteric
- Receiver Xantech
- Receiver Artsound
- Receiver Rolls
- Receiver Sonifex
- Receiver Advance Acoustic
- Receiver Wireless Solution
- Receiver Manley
- Receiver Klark Teknik
- Receiver AVMATRIX
- Receiver Mark Levinson
- Receiver Ocean Matrix
- Receiver Markbass
- Receiver AmpliVox
- Receiver LEA
- Receiver Memphis Audio
- Receiver Televes
- Receiver Aquatic AV
- Receiver Ashly
- Receiver Fishman
- Receiver Integra
- Receiver Blustream
- Receiver CyberData Systems
- Receiver JETI
- Receiver SureCall
- Receiver ANKARO
- Receiver NUVO
- Receiver Audiofrog
- Receiver MuxLab
- Receiver Hegel
- Receiver Triangle
- Receiver Whirlwind
- Receiver Hughes & Kettner
- Receiver Palsonic
- Receiver Musical Fidelity
- Receiver Rexing
- Receiver A-NeuVideo
- Receiver Crest
- Receiver Primare
- Receiver C2G
- Receiver Fosi Audio
- Receiver S.M.S.L
- Receiver Advance
- Receiver AEA
- Receiver TechLogix Networx
- Receiver CE Labs
- Receiver Gold Note
- Receiver Audiotec Fischer
- Receiver Sinus Live
- Receiver Shinybow
- Receiver Shanling
- Receiver Fontastic
- Receiver BC Acoustique
- Receiver NuPrime
- Receiver Creek
- Receiver Valcom
- Receiver Intelix
- Receiver Madison
- Receiver Topp Pro
- Receiver Whistler
- Receiver Powersoft
- Receiver LinksPoint
- Receiver Modelcraft
- Receiver Simaudio
- Receiver FSR
- Receiver Edwards Signaling
- Receiver Quad
- Receiver IOTAVX
- Receiver Inter-M
- Receiver Soundtrack
- Receiver Canor
- Receiver Unison Research
- Receiver Clare Controls
- Receiver Loxjie
- Receiver Cayin
- Receiver Technical Pro
- Receiver VMV
- Receiver Bellari
- Receiver Comprehensive
- Receiver PureLink
- Receiver FoneStar
- Receiver Glemm
Neueste Bedienungsanleitung für -Kategorien-
19 September 2024
19 September 2024
19 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
17 September 2024
17 September 2024