Audio-Technica ES933/C Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Audio-Technica ES933/C (2 Seiten) in der Kategorie Mikrofon. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
CARDIOID CONDENSER
HANGING MICROPHONE
- Designed for quality sound
reinforcement, professional
recording, television and other
demanding sound pickup
applications.
- Superior off-axis rejection for
maximum gain before feedback.
- Furnishing with a vinyl-coated steel
hanger that allows to be adjusted for
correct positioning.
- Accepts interchangeable elements
to permit angle of acceptance from
90° to 120°.
- Snap-on foam windscreen effectively
reduces noise from wind or
ventilation air currents.
- Connected power module can be
powered from any external 11V to
52V phantom power supply with an
XLRM-type connector.
- Enclosed in a rugged housing with
a low-reectance black nish. And
also available with white housing,
cable and hanger as the ES993W/C.
The ES933/C shall have a permanently-attached 15.2m miniature low-
noise cable, and require 11V to 52V DC phantom power for operation.
A uniform 120° angle of acceptance provides well-balanced audio
pickup. The microphone should be located forward of the front-most
source, above the rear-most source, and "aimed" between them (Fig.1).
Increasing the height of the mic above the sources will tend to equalize
sound levels between them, but may also increase from the mic to the
rear-most pickup should be no more than twice the distance to the front
source, to maintain front-to-rear balance (Fig.1).
Width of pickup is approximately three times the distance to the closest
performer. If additional mics are needed for wide sources, they should
be positioned apart laterally at least three times the distance to front
source, to avoid phase cancellation (Fig.2).
Output is low impedance balanced. The output connector mates with
XLRF-type cable connectors. The balanced signal appears across Pins
2 and 3, while the ground (shield) connection is Pin 1. Output is phased
so that positive acoustic pressure produces positive voltage at Pin 2, in
accordance with industry convention.
At integral 80 Hz high-pass filter provides easy switching from a flat
frequency response to a low-end roll-off. The roll-off position reduces
the pickup of low-frequency ambient noise (such as trafc, air-handling
systems, etc.), room reverberation and mechanically coupled vibrations.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 43°C for extended periods. Extremely high
humidity should also be avoided.
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Optional Accessories:
AT8506 four-channel 48V phantom power
supply (AC powered).
AT8801/EU single-channel 48V phantom
power supply (AC powered).
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Roll-off
Response in dB
FORM No. ATGC-L0055-06-E
Machida Tokyo Japan
SPECIFICATIONS
ELEMENT Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN Cardioid
FREQUENCY RESPONSE 30-20,000 Hz
LOW-FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave
OPEN CIRCUIT SENSITIVITY -40 dB (10.0 mV) re 1V at 1 Pa
IMPEDANCE 250 Ω (1000 Ω without power module)
MAXIMUM INPUT SOUND LEVEL 138 dB SPL, 1 kHz at 1% T.H.D.
DYNAMIC RANGE (typical) 109 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO 65 dB, 1 kHz at 1Pa
SWITCHES Flat response, low-roll-off
PHANTOM POWER REQUIREMENTS 11-52V DC, 4 mA typical
WEIGHT Microphone
Power Module
5 g
56 g
DIMENSIONS Microphone
Power Module
23.3 mm - long,
8.4 mm - head diameter
98.0 mm - long,
18.9 mm - diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
CABLE 15.2m - long, 3.2 mm - diameter
ACCESSORIES FURNISHED AT8109 snap-on foam windscreen
AT8452 steel hanger
OPTIONAL INTERCHANGEABLE
ELEMENTS
ESE-H hypercardioid (100°)
ESE-ML MicroLine ® (90°)
3 TIMES
DISTANCE "X"
MIC A MIC B
120° 120°
120°
ANGLE OF
ACCEPTANCE
DISTANCE "X"
LESS THAN 2 TIMES "X"
Fig.2Fig.1
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
指向特性
频率特性
声压曲线
1刻度5 dB
频率
频率 (赫兹)
电平 平直
高通滤波
响应电平 (dB)
FORM No. ATGC-L0055-06-C
Machida Tokyo Japan
心形指向性 悬挂式
专业型电容话筒
-
、电视广播、会议等高要
-
-
固定调校到任何正确位置。
-
9 0 °
120°
-
低在讲话时收到其他风声
的情况出现。
- 连接到 11 V 5 2 V 话筒前置
线 3
XLR M
-
白色的 ES9 33W /C型号。
E S 9 3 3 / C 1 5 . 2 m 线
11V 52V
1 2 0 °。 话 筒 安 装 应 先
定最前及最后的声源位置,而话筒应瞄准两者之间的中央
( ) 使 1
却可能会增加背景噪音声及回声,所以调校话筒时,应避
( ) 1
平衡。
而与其他话筒的宽度距离,应以最前声源的大致三倍距离
( ) 2
2 3
针脚输出,而 1 针脚则为地线() 连接。输出相位将
2
内置高质量高通滤波电路,可轻易由平直的频率响应,
80 H z 以下衰减的收音效果,应高通滤波器可低收
(
)
弱,应避免将话筒留在日晒的地方或长时间置于温度超
43° C 湿
选择配件:
AT8506 四通通48V幻象供电器 (交流供电)
AT8801/EU 单通道48V幻象供电器 (交流供电)
技术指标
收音头 固定充电背板,
静电型电容式
指向特性 心形单指向性
频率响应 30-20,000 Hz
高通滤波 80 Hz, 12 dB/octave
开通灵敏度 -40 dB (10.0 mV)
1V 1 Pa
输出阻抗 250 欧姆 (不带供电模组1000 欧姆)
最大承受声压 138 dB 声压, 1 kHz 1% T.H.D.
动态范围 (典型) 109 dB, 1 kHz
于最高声压
讯噪比 65 dB, 1 kHz 1Pa
开关 平直,高通滤波
幻象供电 直流 11-52V DC, 耗电 4 mA 典型
重量 话筒
供电模组
5
56
外形尺寸 话筒
供电模组
23.3 mm -
长,8.4 mm - 收音头直径
98.0 mm -
长,18.9 mm - 直径
输出连接器 内置式3针卡农公头
连接线 15.2 m - 长,3.2 mm - 直径
附属品 AT8109 双层式防风海棉罩
AT8452 悬挂弹簧
可转换收音头 ESE-H 超心形指向
(100°)
ESE-ML MicroLine®
超指向性 (90°)
3倍距离:
"3X"
话筒 A 话筒 B
120° 120°
120°
一般收音角度
与收音头的距离
"X"
最远距离少于 2倍:
"2X"
21


Produktspezifikationen

Marke: Audio-Technica
Kategorie: Mikrofon
Modell: ES933/C

Brauchst du Hilfe?

Wenn Sie Hilfe mit Audio-Technica ES933/C benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Mikrofon Audio-Technica

Bedienungsanleitung Mikrofon

Neueste Bedienungsanleitung für -Kategorien-