Audio-Technica ATM710 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Audio-Technica ATM710 (2 Seiten) in der Kategorie Mikrofon. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
CARDIOID CONDENSER VOCAL MICROPHONE
- Tailored for exacting detail, high-delity vocal reproduction with maxi-
mum impact and intelligibility.
- Excels in venues with controlled stage volume or in-ear monitoring.
- Cardioid polar pattern reduces pickup of sounds from the sides and rear,
improving isolation of desired sound source.
- Durable performance for professional applications.
- Superior anti-shock engineering for low handling noise.
- Multi-stage grille design offers excellent protection against plosives and
sibilance without compromising high-frequency clarity.
- Condenser design for studio-quality performance.
- Integral 80Hz HPF switch and 10 dB pad.
- Corrosion-resistant contacts from gold-plated XLRM-type connector.
- Rugged, all-metal design and construction for years of trouble-free use.
The ATM710 is intended for use in professional applications where remote
power is available. It required 11V to 52V DC phantom power, which may
be provided by a mixer or console, or by a separate, in-line source such
as the Audio-Technica AT8801 single-channel or AT8506 four-channel
phantom power supplies.
Output from the microphone’s XLRM-type connector is low impedance
(Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground
(shield). Output phase is “Pin 2 hot” - positive acoustic pressure produces
positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be wired
consistently: Pin 1-to-Pin 1, etc.
When using the ATM710 in settings with a stage monitor speaker, the
speaker should be located 180° off axis (at rear of the microphone). This
placement, in conjunction with the microphones uniform cardioid pickup
pattern, will virtually eliminate the possibility of undesired audio feedback.
An integral 80Hz hi-pass filter provides easy switching from a flat fre-
quency response to a low-end roll-off. The roll-off position reduces the
microphone’s sensitivity to popping in close vocal use. It also reduces the
pickup of low-frequency ambient noise (such as trafc, air-handling sys-
tems, etc.), room reverberation and mechanically coupled vibrations.
The ATM710 is also equipped with a switchable 10 dB pad that lowers the
microphones’s sensitivity, thus providing higher SPL capability for exible
use with a wide range of performers and system congurations.
Avoid leaving the microphone in the open sun or in areas where tempera-
tures exceed 40°C for extended periods. Extremely high humidity should
also be avoided.
FORM No. ATGC-L0026-06-E
Machida Tokyo Japan
SPECIFICATIONS
ELEMENT Fixed-change back plate permanently
polarized condenser
POLAR PATTERN Cardioid
FREQUENCY RESPONSE 40-20,000 Hz
LOW FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave
OPEN CIRCUIT SENSITIVITY -40 dB (10.0 mV) re 1V at 1 Pa
IMPEDANCE 200 ohms
MAXIMUM INPUT SOUND LEVEL 148 dB SPL, 1 kHz at 1% T.H.D.
DYNAMIC RANGE (typical) 127 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO 73 dB, 1 kHz at 1 Pa
PHANTOM POWER REQUIREMENTS 11-52V DC, 3.5 mA typical
SWITCHES Flat, roll-off; 10 dB pad
WEIGHT 274 g
DIMENSIONS 179.0 mm - long,
50.0 mm - diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED AT8470 Quiet-Flex™ stand clamp for
⅝”-27 threaded stand;
⅝”-27 to ⅜”-16 threaded adapter;
Soft protective pouch
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
Roll-off
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
指向特性
频率特性
声压曲线 1刻度5 dB
频率
频率 (赫兹)
电平 平直
响应电平 (dB)
FORM No. ATGC-L0026-06-C
Machida Tokyo Japan
心形指向性电容式话音话筒
-
越的
- 擅长在舞台上有音量控制或耳机监听的应用。
- 心形指向性收音,能有效减低旁边及后方的杂声干扰。
- 应用
- 的抗效减声。
-
高音
- 录音音头
- 80Hz内置 及 衰10dB
- 蚀的XLRM卡农输出头。
- 全金、耐使用。
ATM710 11V 52V应用于专业收音工作,需要提供 至 幻象供电,可
使用调音台上的幻象电源,也可以使用鐵三角的AT8801单通道或
AT8506四通道幻象电源供电器作独立供电。
话筒的 卡农输出端为低阻抗平衡输出,号最XLRM
以卡农公头的23号针脚输出,而1号针脚则为地线()
接。出相电平2号针脚上。
为避免出现相位相互抵消而失真的情况,所有话筒连接时,
线必需1-12-23-3型式把针脚连接。
ATM710话筒及现场监听音箱同时使用时,需要把音箱放置于
话筒的 180°正后方。在这位置上,由于话筒的心形指向性设计,
可减低出现反馈回声的情况。
置高通滤波电路,可轻易由平直的频率响应,开启为于 80 Hz
以下衰减的收音效果,应用高通滤波器可减低话筒在近距离讲话
收音时的喷气声,并可减低收音环境中低频噪声 (如外间汔车引
擎声,空调系统的风声等 )
,房间中的回声及机械性的震动声。
话筒并设有10dB衰减开关,在高声压环境收音时,减低话筒的灵
敏度,避免破声的失真现象出现。
把话筒暴露于高温中可能导致输出电平逐渐及永久性减弱,应避
免将话筒留在日晒的地方或长时间置于温度超过 43°C的地方,而
极高湿度也应避免。
技术指标
收音头 固定充电背板,静电型电容式
指向特性 心形指向性
频率响应 40-20,000 Hz
高通滤波 80 Hz, 12 dB/octave
开通灵敏度 -40 dB (10.0 mV) 1V 1 Pa
输出阻抗 200 欧姆
最大承受声压 148 dB 声压, 1 kHz 1% T.H.D.
动态范围 (典型) 127 dB, 1 kHz 于最高声压
讯噪比 73 dB, 1 kHz 1 Pa
幻象供电 直流 11-52V, 耗电
3.5 mA 典型
开关 高通滤波;10 dB 衰减
重量(不带连线与配件) 274
外形尺寸 179.0 mm - 长度,
50.0 mm - 直径
输出连接器 内置 XLRM-3针卡农公头
附属品 AT8470 Quiet-Flex™ - ⅝”-27接头
⅝”-27⅜”-16转接头,保護袋。
高通滤波


Produktspezifikationen

Marke: Audio-Technica
Kategorie: Mikrofon
Modell: ATM710

Brauchst du Hilfe?

Wenn Sie Hilfe mit Audio-Technica ATM710 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Mikrofon Audio-Technica

Bedienungsanleitung Mikrofon

Neueste Bedienungsanleitung für -Kategorien-