Atlas FAP6260T Bedienungsanleitung

Atlas Lautsprecher FAP6260T

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Atlas FAP6260T (1 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
Ceiling Material up to 2"
Tile Bridge
Auxiliary Suspension int Po
Dogleg In Inverted sition Po
FAP6260T
Installation Instructions
ATS004631 RevA 7/13
FAP6260T
Installation Instructions
Mounting Template
9
916
" Diameter
The Atlas Sound Strategy Series® III assembly mounts easily into existing
construction drop ceiling or drywall materials.
Drop Tile Ceiling Installation
1. Remove 2' 2' or 2' 4' tile. x x
2. Align adjustable dual rail -ring assembly on rear of tile in& C
desired position.
3. Using template provided mark cut out circle with marker and cut hole. the ,
(9916" FAP6260T)
4. Affix -ring assembly to rails using screws provided and position assembly on rear of ceiling tile. C
Replace tile into grid formed ends of tile bridge rails engage T-bar tile support rails.. Ensure
5. Bring service loop from rear of tile, through tile bridge C-ring to access panel located on of the / the top
enclosure. Terminate the service loop to Phoenix style connector provided (please note polarity).
6. Insert enclosure through front of tile. Using standard #2 Phillips screwdriver or screw-gun,
tighten four dogleg assemblies
until they engage C-ring assembly. the DO NOT OVER-TIGHTEN DOGLEG SCREWS!
7. Adjust front mounted switch to desired tap setting or 8power Ω* (See important note regarding 8 operation)Ω
8. Place grille on front of unit by aligning the tabs on the underside of grille with the notches on the unit bezel.
Allow magnets to hold the grille while rotating to lock the securing tabs.
9. For safety and seismic considerations a suspension ring is integrated into input panel section of unit. the
Atlas Sound strongly suggests that a support wire be installed from this support point to a suitable anchor point above ceiling grid.
In drop tile applications, this wire can usually be installed from an adjacent tile access near speaker location.
Dry Wall ("Hard Deck") Installation
1. Using the template provided, mark cut out circle in desired mounting location and cut hole. ( 9 916" FAP6260T)
2. Place tile bridge rails and C-ring through hole. Use V shaped edge of C-ring to align tile bridge assembly above ceiling-
(alignment screws provided are not required for this type of installation)
3. Bring service loop from rear of tile, through the tile bridge / C-ring to access panel located on side of the enclosure. Terminate service loop to the
Phoenix style connector provided (please note polarity).
4. Insert enclosure into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten dogleg assemblies until they engage the C-ring assembly.four
DO NOT OVER-TIGHTEN DOGLEG SCREWS!
5. Adjust front mounted switch to desired tap setting or 8power Ω* (See important note regarding 8 operation)Ω
6. Place grille on front of unit by aligning the tabs on the underside of grille with the notches on the unit bezel.
Allow magnets to hold the grille while rotating to lock the securing tabs.
NOTE: Doglegs will accommodate ceiling material thickness up to 1
12" as shipped from factory. For thicker ceiling materials (up to 2") simply unscrew and flip doglegs
as shown. DO NOT OVER-TIGHTEN DOGLEGS IN EITHER CONFIGURATION!
NOTE: UL recognized conduit clamp must be used for conduit connections. Cable connection cavity is not intended to be used as a junction box.
NOTE: *DO NOT USE 8 SETTING WITH 70.7V / 100V SYSTEMS! *DO NOT OVERPOWER IN 8 CONFIGURATION! Ω Ω
AMPLIFIER OUTPUT SHOULD NOT EXCEED 60 W RMS @ 8 PER SPEAKERΩ
15W @ 70.7V
Full nge Ra
15W @ 70.7V
Full nge Ra
15W @ 70.7V
FAP6260T-B FAP6260T-BFAP6260T-BFAP6260T-B
Full nge Ra
15W @ 70.7V
Full nge Ra
Tap wer Total: 60 Po Watts
Typical 120 tt 70.7V Output Wa
Typical rallel Hookup of Full Range 70.7V/100V SpeakersPa
1 4 5 as er o
Amplifier
Input
-
+
- + - + - + - +
Ceiling Material up to 1-1/2"
Auxiliary Suspension int Po
Tile Bridge
Dogleg In Normal Position
ATS004631 RevA 7/13
Grille tabs aligned with
notches on the unit bezel
Grille tabs secured to the
unit bezel


Produktspezifikationen

Marke: Atlas
Kategorie: Lautsprecher
Modell: FAP6260T

Brauchst du Hilfe?

Wenn Sie Hilfe mit Atlas FAP6260T benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher Atlas

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-