Arctic Silver lean Bedienungsanleitung
Arctic
CPU Kühler
Silver lean
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Arctic Silver lean (7 Seiten) in der Kategorie CPU Kühler. Dieser Bedienungsanleitung war für 40 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/7
Arctic Silver Instructions
Application Instructions for Premium Silver Thermal Compound
on a large contact area (Intel P4 AMD64)
Arctic Silver, Arctic Silver II, Arctic Silver 3 and Arctic Silver 5.
Important Precautions
Don't put it in your mouth. .
Don't give it to children or leave it where children can get a hold of it.
Keep it away from pets.
Follow the instructions at the bottom of this page to clean it off of yourself, your CPU, and other
hardware.
Caution:
While much safer than silver greases engineered for high electrical conductivity, Arctic Silver
thermal compound should be kept away from electrical traces, pins, and leads. The compound is
slightly capacitive and could cause problems if it bridged two close-proximity electrical paths.
Caution:
Never turn on a computer without a heatsink properly mounted on the CPU with a thermal interface
material between the CPU core and the heatsink. A modern high-performance CPU can be
permanently damaged in less than 10 seconds without proper cooling.
Caution:
Arctic Silver is a grease and does not have any adhesive qualities. It will never dry or set and
cannot be used to glue a heatsink to a chip.
To permanently glue a heatsink to a chip that does not have any other attachment method, please
use Arctic Silver Adhesive or Arctic Alumina Adhesive.
Caution:
We do not recommend using Arctic Silver on the older slot type Intel Xeon processors with large
multiple square inch CPU to heatsink interfaces. The huge contact area and large gaps between
the processor and the heatsink require a thermal pad or thick mesh-reinforced paste.
Arctic Silver can be used on socket type Xeons without a problem.
http://articsilver.com/arctic_silver_instructions_big2.htm (1 of 7)5/28/2005 4:02:16 AM
Arctic Silver Instructions
Important Reminder:
Due to the unique shape and sizes of the particles in Arctic Silver's conductive matrix, it will take a
up to 200 hours and several thermal cycles to achieve maximum particle to particle thermal
conduction and for the heatsink to CPU interface to reach maximum conductivity. (This period will
be longer in a system without a fan on the heatsink or with a low speed fan on the heatsink.) On
systems measuring actual internal core temperatures via the CPU's internal diode, the measured
temperature will often drop 2C to 5C over this "break-in" period. This break-in will occur during the
normal use of the computer as long as the computer is turned off from time to time and the
interface is allowed to cool to room temperature. Once the break-in is complete, the computer can
be left on if desired.
Application Instructions
1. Even though Arctic Silver thermal compound is specifically engineered for high electrical
resistance, you should keep the compound away from processor, memory, and motherboard
traces and pins. There is a possibility that dust or metal particles and/or shavings carried by the
airflow inside the computer case could contaminate the compound and increase its electrical
conductivity.
2. ONLY Arctic Silver thermal compound should be between the processor core and the heatsink.
Remove any thermal pads or other interface material from the heatsink before applying the Arctic
Silver. Thermal pads can be scraped off with a plastic tool that will not scratch the bottom then
the remnants can be removed with ArctiClean 1Thermal Material Remover and ArctiClean 2
Thermal Surface Purifier. If you do not have ArctiClean, use a xylene based cleaner, (Goof Off and
some carburetor cleaners) acetone, mineral spirits, or high-purity isopropyl alcohol.
Never use any oil or petroleum based cleaners (WD-40, oil based grease removers and many
automotive degreasers) on the base of a heatsink. If you use a citrus based cleaner, you must use
ArctiClean 2 Thermal Surface Purifier to remove the citrus oil before applying new thermal
material, Any oil remaining on the heatsink will fill in the microscopic valleys in the metal and
significantly reduce the effectiveness of any subsequently applied thermal compound.
If your heatsink has a thermal 'pad' mounted on it, this pad must be removed before using Arctic
Silver thermal compound. Thermal pads are made with paraffin wax that melts once it gets hot.
When it melts, it will fill in the microscopic valleys in the heatsink with wax. To minimize the
permanent contamination of the mounting surface with wax, the thermal pad should be removed
before it is used and melted. Never use heat or hot water to remove the pad, the heat will melt the
wax into the heatsink.
http://articsilver.com/arctic_silver_instructions_big2.htm (2 of 7)5/28/2005 4:02:16 AM
Arctic Silver Instructions
3. Clean the mating surfaces completely with ArctiClean 2 Thermal Surface Purifier or a low residual
solvent (High-purity isopropyl alcohol or acetone will work) and a LINT FREE cloth. (i.e. a coffee
filter) If another thermal compound has previously been applied to the heatsink, the mounting
surfaces should be thoroughly scrubbed and cleaned with ArctiClean 1 Thermal Material Remover
followed by ArctiClean 2 Thermal Surface Purifier. If you do not have ArctiClean, a xylene based
cleaner, (Goof Off and some carburetor cleaners) acetone, mineral spirits, or 99% pure isopropyl
alcohol can be used. It is important to keep the surfaces free of foreign materials and NOT
to touch the surfaces (a hair, piece of lint, and even dead skin cells can significantly affect the
thermal interfaces performance). In addition, oils from your fingers can adversely affect the
performance by preventing the micronized silver fill from directly contacting the metal surface.
(Fingerprints can be as thick as 0.005")
4. For Arctic Silver 1, 2 and 3:
Determine what area on the base of the heatsink will contact the CPU core once the heatsink is
mounted. Squeeze Twist the plunger in the syringe barrel at least 1/2 turn to ensure that it is free.
enough Arctic Silver thermal compound onto the center of this area to create a small mound as
shown in the photo below.
5. Using the compound you applied to the base of the
heatsink, tint the bottom of the heatsink in the area
where the CPU will contact it. Put a finger into a
plastic bag and thoroughly rub the compound into
the base of the heatsink using both clockwise and
counter-clockwise circular motion. This will ensure
optimum filling of the microscopic valleys in the
metal.
DO NOT use your bare finger to apply or smooth
the compound (skin cells, and oils again).
http://articsilver.com/arctic_silver_instructions_big2.htm (3 of 7)5/28/2005 4:02:16 AM
Produktspezifikationen
| Marke: | Arctic |
| Kategorie: | CPU Kühler |
| Modell: | Silver lean |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Arctic Silver lean benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung CPU Kühler Arctic
12 Juni 2023
Bedienungsanleitung CPU Kühler
- CPU Kühler Asus
- CPU Kühler Corsair
- CPU Kühler Zalman
- CPU Kühler LC-Power
- CPU Kühler Enermax
- CPU Kühler Cooler Master
- CPU Kühler SilverStone
- CPU Kühler Thermaltake
- CPU Kühler Be Quiet!
- CPU Kühler Noctua
- CPU Kühler CyberPower
- CPU Kühler Antec
Neueste Bedienungsanleitung für -Kategorien-
5 Juli 2024
5 Juli 2024
24 Mai 2024
16 Mai 2024
8 Mai 2024
30 April 2024