APC Back-UPS ES 350 Bedienungsanleitung

APC Unterbrechungsfreies Stromversorgungssystem Back-UPS ES 350

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für APC Back-UPS ES 350 (2 Seiten) in der Kategorie Unterbrechungsfreies Stromversorgungssystem. Dieser Bedienungsanleitung war für 45 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Safety

Specifications

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!

Connect the Battery” label that covers the outlets. Prior to connecting any equipment

to the unit, connect the battery cable to the unused battery terminal. It is normal for

small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

• Horizontal installation, use 2 screws 5.0" (127 mm) apart.

• Vertical installation, use 2 screws 4.3" (110.4 mm) apart.

• Allow 5/16" (8 mm), of the screw to protrude from the wall.

Connect Equipment

Battery Backup + Surge Protection Outlets

Battery backup outlets provide protection to connected equipment when the

Back-UPS is turned on and connected to utility power.

Battery backup outlets receive power from the Back-UPS for a limited period of time

when a power outage, or brownout condition occurs.

Battery backup outlets provide protection from power surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection Outlets

Surge protection outlets provide protection to connected equipment when the

Back-UPS is connected to utility power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices that do not need to remain on

during power outages, or utility problems to the surge protection outlets.

Connect telephone line

The Back-UPS protects equipment connected to a telephone line from power surges

when connected through the Back-UPS coaxial connectors.

Turn On the Back-UPS

Press the POWER ON button located on the top of the Back-UPS. The Power On/

Replace Battery LED will illuminate and a single short beep will be audible to

indicate that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first 16 hours while connected to

utility power. The Back-UPS battery will charge while the Back-UPS is switched on

or off and is connected to utility power. Do not expect full battery run capability

during the initial charge time.

If the red Building Wiring Fault LED located on the side of the Back-UPS

illuminates, do not operate the Back-UPS. Have a qualified electrician correct the

building wiring fault.

Voltage Sensitivity Adjustment (optional)

The Back-UPS detects and reacts to line voltage distortions by transferring to battery

backup power to protect connected equipment. In situations where either the

Back-UPS or the connected equipment is too sensitive for the input voltage level it is

necessary to adjust the transfer voltage.

1. Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode,

no indicators will be illuminated.

2. Press and hold the ON/OFF button for 10 seconds. The OnLine LED will

illuminate alternately green-amber-red, to indicate that the Back-UPS is in

Program mode.

3. The Power On/Replace Battery LED will flash either green, amber, or red to

indicate the current sensitivity level. Refer to the table for an explanation of the

transfer voltage sensitivity levels.

4. To select LOW sensitivity, press and hold the ON/OFF button until the LED

flashes green.

5. To select MEDIUM sensitivity, press and hold the ON/OFF button until the LED

flashes red.

6. To select HIGH sensitivity, press and hold the ON/OFF button until the LED

flashes amber.

7. To exit Program mode wait five seconds and all LED indicators will extinguish.

Program mode is no longer active.

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in

contact with fluids, or where there is

excessive dust or humidity.

Connect the Back-UPS power cord directly to

a wall outlet. Do not use a surge protector or

an extension cord.

Input

Voltage 120 Vac Nominal

Frequency 60 Hz + 3

Brownout Transfers 92 Vac Typical

Over-voltage Transfer 139 Vac Typical

Output

UPS Capacity (3 outlets) 350 VA, 200 W

Total Amperage (6

outlets)

8 A (including UPS output)

Voltage - On Battery 115 Vac ± 8%

Frequency - On Battery 60 Hz + 1

Transfer Time 6 ms Typical, 10 ms maximum

Protection

and

Filtering

AC Surge Protection Full time, 340 Joules

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery

Type Sealed, maintenance-free, lead

acid Replacement battery cartridge

RBC35

Average Life 3 - 5 years depending on the

number of discharge cycles and

environmental temperature

Physical

Net Weight 9 lb (4 kg)

Dimensions

Length x Width x Height

11 in x 6 in x 3 in

29 cm x 16 cm x 9 cm

Operating Temperature 32º F to 104º F (0º C to 40º C)

Storage Temperature 5º F to 113º F (–15º C to 45º C)

Operating Relative

Humidity 0 to 95% non-condensing

humidity

Operating Elevation 0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC

rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) This

device must accept any interference received, including

interference that may cause undesired operation.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely to

the battery terminal.

 Reinstall the battery compartment

cover. Be sure that the release tab locks

into place.

bu064a

bu065a

bu066a

LED

Flashes Sensitivity

Setting Input Voltage Range

(Utility Operation) Recommended Use

Green LOW 88 Vac to 142 Vac Use this setting with equipment that

is less sensitive to fluctuations in

voltage or waveform distortions.

Red MEDIUM 92 Vac to 139 Vac Factory default setting. Use this

setting under normal conditions.

Amber HIGH 96 Vac to 136 Vac Use this setting when connected

equipment is sensitive to voltage

and waveform fluctuations.

bu206a

Back-UPS

Battery Backup +

Surge Protection

bu230a

CAUTION-Refer to bottom

of unit for safety markings.

Circuit

Breaker

Building

Wiring Fault

Te l

Out

Push to

Reset

Te l

User Manual Back-UPS® BE350G Series

990-4418B

7/2011

Corporation, or their eir respective owners.affiliated companies. All other trademarks are property of th

Status Indicators

Troubleshooting Replace Battery

Use only approved APC replacement battery cartridges.

Deliver used batteries to a battery replacement facility in the packaging provided by

APC with the replacement battery cartridge.

To order replacement battery cartridges contact APC through the Web site

www.apc.com

Warranty

The standard warranty is two (2) years from the date of purchase. APC

standard procedure is to replace the original unit with a factory reconditioned

unit. Customers who must have the original unit back due to the assignment

of asset tags and set depreciation schedules must declare such a need at first

contact with an APC Technical Support representative. APC will ship the

replacement unit once the defective unit has been received by the repair

department, or cross-ship upon the receipt of a valid credit card number. The

customer pays for shipping the unit to APC. APC pays ground freight

transportation costs to ship the replacement unit to the customer.

Service

If the unit requires service, do not return it to the dealer. Follow these steps:

1. Review the Troubleshooting section of the manual to eliminate common

problems.

2. If the problem persists, contact APC Customer Support.

a. Note the model number and serial number and the date of purchase. The

model and serial numbers are located on the rear panel of the unit and are

available through the LCD display on select models.

b. Call APC Customer Support and a technician will attempt to solve the

problem over the phone. If this is not possible, the technician will issue a

Returned Material Authorization Number (RMA#).

c. If the unit is under warranty, the repairs are free.

d. Service procedures and returns may vary internationally. Refer to the APC

Web site for country specific instructions.

3. Pack the unit properly to avoid damage in transit. Never use foam beads for

packaging. Damage sustained in transit is not covered under warranty. Always

DISCONNECT THE UPS BATTERY before shipping in compliance with

U.S. Department of Transportation (DOT) and IATA regulations. The battery

may remain in the unit.

4. Write the RMA# provided by Customer Support on the outside of the package.

5. Return the unit by insured, pre-paid carrier to the address provided by Customer

Support.

Contact

APC Web site, www.apc.com

Status LED Indicator Audible Indicator On Audible Indicator Terminates

Power On

The Back-UPS is supplying utility power to connected

equipment.

The green LED illuminates. None N/A

On Battery

Back-UPS supplying battery power to battery backup outlets.

The green LED illuminates.The LED

is not illuminated during the beeps. Back-UPS beeps 4 times

every 30 seconds. Beeping stops when utility power is restored or the

Back-UPS is turned off.

Low Battery warning

The Back-UPS is supplying battery power to the battery backup

outlets and the battery is near a total discharge state.

The green LED illuminates with rapid

green flashes. The Back-UPS emits rapid

beeping, every 1/2 second. Beeping stops when utility power is restored or the

Back-UPS is turned off.

Replace Battery

• The battery is disconnected.

• The battery needs to be charged, or replaced.

•Replace Battery LED flashes.

•Replace Battery and Power On

LEDs flash alternately.

Constant tone

Constant tone Back-UPS is turned off.

Overload Shutdown

While on battery power an overload condition has occurred in

one or more of the battery backup outlets while the

Back-UPS is operating on battery power.

None Constant tone Back-UPS is turned off.

Sleep Mode

While on battery power the battery is completely discharged.

The Back-UPS will “awaken” once utility power is restored. None The Back-UPS beeps once

every four seconds.

The beeping stops when:

• Utility power is restored

• If utility power is not restored within 32 seconds

• The Back-UPS is turned off

Building Wiring Fault

The building wiring presents a shock hazard that must be

corrected by a qualified electrical.

Building Wiring Fault

LED illuminates red

None The Back-UPS is unplugged from the wall outlet

or is plugged into an improperly wired outlet.

Problem and Possible Cause Solution

The Back-UPS will not turn on

The Back-UPS has not been turned

on.

Press the Power on button.

The Back-UPS is not connected to

utility power, there is no utility

power available at the wall outlet, or

the utility power is experiencing a

brownout or over voltage condition.

Make sure the power cord is securely connected

to the wall outlet, and that there is utility power

available at the wall outlet.Where applicable,

check that the wall outlet is switched on.

The battery is not connected. Connect the battery. Refer to “Connect the

Battery” on page 1 of this manual.

In the event that the Back-UPS receives no utility

power and the battery is connected, a cold-start

can be initiated. Press and hold the Power On

button until the Back-UPS emits two beeps.

The Back-UPS is on, the Replace Battery LED flashes and the unit emits a

constant tone

The battery is disconnected. Refer to the “Connect the Battery” on page 1.

Connected equipment loses power

A Back-UPS overload condition has

occurred. Remove all nonessential equipment connected to

the outlets. One at a time reconnect equipment to

the Back-UPS.

The Back-UPS battery is completely

discharged. Connect the Back-UPS to utility power and allow

the battery to recharge for eight hours.

PowerChute software has performed

a shutdown due to a power failure. This is normal Back-UPS operation.

Connected equipment does not

accept the step-approximated sine

waveform from the Back-UPS.

The output waveform is intended for computers

and peripheral devices. It is not intended for use

with motor driven equipment.

The Back-UPS may require service. Contact APC Technical Support for more in

depth troubleshooting.

The Power On LED is illuminated and the Back-UPS beeps 4 times every

30 seconds

The Back-UPS is operating on

battery power. The Back-UPS is operating normally on battery

power. At this point the user should save all open

files, and shutdown the computer. When utility

power is restored the battery will recharge.

The Power On LED flashes once every second while the Back-UPS beeps

once every second

The Back-UPS battery has

approximately two minutes of

remaining runtime.

The Back-UPS battery is near a total discharge

state. At this point the user should save all open

files, and shutdown the computer. When utility

power is restored the battery will recharge.

The Back-UPS has an inadequate battery runtime

The battery is not fully charged.

The battery is near the end of useful

life and should be replaced.

Leave the Back-UPS connected to utility power

for 16 hours while the battery charges to full

capacity.

As a battery ages, the runtime capability

decreases. Contact APC at the Web site

www.apc.com, to order replacement batteries.

The Building Wiring Fault LED illuminates

The building wiring presents a shock

hazard that must be corrected by a

qualified electrical.

Do not operate the Back-UPS. Call a qualified

electrician to correct the building wiring fault.

The connection from the Back-UPS to the internet is lost during a power

outage

The modem has lost power. Connect the modem cable into one of the Battery

Backup + Surge Protection outlets.

Produktspezifikationen

Marke:	APC
Kategorie:	Unterbrechungsfreies Stromversorgungssystem
Modell:	Back-UPS ES 350
Akustische Signale:	Ja
Breite:	159 mm
Tiefe:	279 mm
Gewicht:	3640 g
Produktfarbe:	Schwarz
Akku-/Batterietyp:	RBC35
Akkuladezeit:	16 h
Akku-/Batterietechnologie:	Plombierte Bleisäure (VRLA)
Höhe:	89 mm
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Paketgewicht:	3910 g
Zertifizierung:	cUL, FCC, NOM
Kabellänge:	1.52 m
LED-Anzeigen:	Batterieaustausch
Temperaturbereich bei Lagerung:	-15 - 45 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Geräuschpegel:	45 dB
Formfaktor:	Kompakt
Ausgangsleistung:	200 W
Filterung:	Ja
Nachhaltigkeitszertifikate:	RoHS
Eingangsfrequenz:	50/60 Hz
Höhe bei Betrieb:	0 - 3000 m
Anzahl der AC-Ausgänge:	6 AC-Ausgänge
Eingangs-Betriebsspannung (min):	- V
Eingangs-Betriebsspannung (max):	- V
Ausgangskapazität:	0.35 kVA
Ausgangs-Betriebsspannung (min):	- V
Ausgangs-Betriebsspannung (max):	- V
Modem (RJ-11) Port:	2
AC-Steckertypen:	NEMA 5–15R
Druckanstiegsschutz:	Ja
Akustische Alarm-Modi:	Batterieaustausch
Nominale Eingang Spannung:	120 V
Nominale Ausgang Spannung:	120 V
Höhe bei Lagerung:	0 - 15000 m
Überspannungsschutz-Funktionen:	Fax, Modem, Telephone
Anstieg der Energiemenge:	365 J