APart CHAMP-4 Bedienungsanleitung

APart Empfänger CHAMP-4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für APart CHAMP-4 (12 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

Champ - 4

Professional quad power amplier

• Caution: hot and sharp surfaces ! This professional device needs to be installed by

qualied personnel only.

Please check the carton box for any kind of damage on reception of the goods. In case of a •

damaged carton, please contact your dealer before opening the carton.

!!!! Danger !!!! Exposure to extremely high noise levels may cause a permanent hearing •

loss. Individuals vary considerably to noise induced hearing loss but nearly everyone will lose

somehearingifexposedtosufcientlyintensenoiseforasufcientamountoftime.Therefore

it is recommended that all persons exposed to equipment capable of producing high sound

pressurelevels,suchasthisamplier,beprotectedbyhearingprotectionwhileinstallingor

operating this unit.

• Read all documentation before operating your equipment.

Keep all documentation for future reference.•

Save the carton and packing material even if the equipment has arrived in good condition.•

Should you ever need to ship the unit, use only the original factory packing.•

Do not spill water or other liquids into or on the unit.•

Make sure power outlets conform to the power requirements listed on the back of the unit.•

Do not use the unit if the electrical power cord is frayed or broken.•

Always operate the unit with the AC ground wire connected to the electrical system ground.•

Havegaincontrolsonampliersturneddownduringpower-uptopreventspeakerdamageif•

there are high signal levels at the inputs.

Donotconnecttheinputs/outputsofampliersorconsolestoanyothervoltagesource,such•

asabattery,mainssource,orpowersupply,regardlessofwhethertheamplierorconsoleis

turned on or oﬀ.

Power down & disconnect units from mains voltage before making connections.•

Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.•

Donotoperateequipmentonasurfaceorinanenvironmentwhichmaydistortthenormalow•

of air around the unit. If the unit is used in an extremely dusty or smoky environment, the unit

should be periodically “blown free” of dust.

Do not remove the cover. Removing the cover will expose you to potentially dangerous volt-•

ages.

Do not drive the inputs with a signal level higher than that required to drive equipment to full •

output.

Donotruntheoutputofanyamplierbackintoanotherinput.•

Do not ground the red output terminal, never connect a red output terminal to another red •

output terminal.

Incaseofmal-functionthisdeviceshouldbeservicedbyqualiedservicepersonnelonly.•

Customdesignedsidemountheatsinks,fourdiscreteclassABampliersinaoneunit19”•

enclosure.

Switchablehighandlowpassltersforeasyandtroublefreesubwoofer/satelliteapplications.•

IntegratedAPClimitercircuitryandclipindication.Thisintelligentcircuitwillpreventharsh•

distortion caused by clipping, provided that the input signal itself is not distorted of course…

what goes in, comes out.

Bridgeablepowerampliers:doubletheoutputpowerbyunitingthepowerof2ampliers.•

Minimum load impedance in bridge mode is 8 ohms.

Self-supportinglowresonanceframe.Torsionfreefrontandsidepanelconstructionwith•

integrated heatsink assembly.

Solidaluminumbrushedfrontpanelwithremovable19”bracketsandhandlesforuseina•

rack,noadditionalsupportneeded.Withoutthe19”bracketsitwillbeastandaloneunitin

high quality audio systems.

High power toroidal transformer.•

Low impedance power supply for improved dynamic response.•

Solid speaker binding posts.•

4 sets of banana screw plugs included.•

1. Features

2. Inputs and outputs

3. Rack mounting and wiring

4. standalone use

5. Technical specications

Produktspezifikationen

Marke:	APart
Kategorie:	Empfänger
Modell:	CHAMP-4
Gewicht:	7500 g
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabelgebunden
Impedanz:	4 Ohm
Verpackungsbreite:	560 mm
Verpackungstiefe:	550 mm
Verpackungshöhe:	100 mm
Paketgewicht:	9000 g
THD, totalklirren:	0.1 %
Energiebedarf:	230V AC, 50Hz
Frequenzbereich:	20 - 40000 Hz
Abmessungen (BxTxH):	483 x 360 x 44 mm