AMX NI-4100 Bedienungsanleitung

AMX Regler NI-4100

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AMX NI-4100 (2 Seiten) in der Kategorie Regler. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Installation Guide

NI-4100 NetLinx Central Controllers

The NI-4100 series of NetLinx Controllers provide versatility with the ability to integrate the

largest number of devices in the NI Series of Master Controllers, including projectors,

lighting, VCR and DVD players, thermostats and other electronic equipment. In these

technology-driven environments, this solution allows for the future addition of more devices

and control capabilities.

With a perfect mix of compatible formats, the NI-4100 series offers flexibility and

customization for businesses experiencing rapid growth and for homes that demand

seamless integration of technology and design. The NI-4100 series provides higher

performance with a faster processor, up to 256MB of onboard RAM and Duet-compatibility.

The NI-4100’s on-board Master also provides the ability to update installed control card

firmware.

ATTENTION!

Verify you are using the latest NI firmware for the on-board Master. Verify you are using the

latest version of NetLinx Studio (available for download from www.amx.com).

Specifications

Connections and Wiring

Inserting NetLinx Cards into the NetLinx Control Card Slots

NetLinx Cards can be installed into the front card slots. The cards mount horizontally through

the card slot openings on the front panel of the enclosure. To install a NetLinx Card:

FIG. 1 NI-4100

NI-4100 Specifications

Models Available: • NI-4100 64MB Controller (FG2105-06)

•NI-4100/256 256MB Controller (FG2105-26)

Dimensions (HWD): • 5 3/16" x 17" x 9 5/16" (13.2 cm x 43.2 cm x 23.7 cm)

• RU: 3

Power Requirement: • 900 mA @ 12 VDC

Memory: NI-4100:

• 64 MB SDRAM

• 1 MB Non-volatile (NV) SRAM

NI-4100/256:

• 256 MB SDRAM

1 MB Non-volatile (NV) SRAM

Compact Flash: 2GB or greater (upgradeable to 4GB - see Other AMX Equipment).

Note: AMX may increase Flash size at any time in response to market

availability.

Weight: 9.15 lbs (4.15 kg)

Enclosure: Metal with black matte finish

Certifications: FCC Part 15 Class B, CE, and IEC 60950

Front Panel LEDs/Slots:

LINK/ACT

(green):

Blinks when the Ethernet cables are connected and terminated correctly.

Also blinks when receiving Ethernet data packets.

Status (green): Blinks to indicate that the system is programmed and communicating

properly.

Output (red): Blinks when the Controller transmits data, sets channels On and Off, sends

data strings, etc.

Input (yellow): Blinks when the Controller receives data from button pushes, strings,

commands, channel levels, etc.

RS-232/422/485

(red):

Light to indicate that DB9 Ports 1 - 7 are transmitting or receiving RS-232,

422, or 485 data.

Relay (red): Light to indicate the relay channels 1 - 8 are active (closed). These LEDs

reflect the state of the relay on Port 8.

LINK/ACT LED

STATUS LED

INPUT LED

OUTPUT LED RS-232/422/485 Status LEDs

RELAY Status LEDs

IR/SERIAL Status LEDs

I/O Status LEDs

front

rear RS-232/422/485 (Ports 1-7)

ICSNet/ICSHub Ports (provided by optional

Relays (Port 8)

I/O (Port 17)

IR/Serial (Ports 9-16)

PROGRAM Port

CONFIGURATION DIP Switch

ID Pushbutton

ETHERNET

10/100 Port

AxLink Port

12 VDC PWR Connector

Slot 1-4 connectors

ICSNet daughter card)

Cardframe

DIP Switch

Slot 1-4 connectors

NI-4100 Specifications (Cont.)

IR/Serial (red): Light to indicate the IR/Serial channels 1 - 8 are transmitting control data on

Ports 9 - 16. LED indictor for each IR port remains lit for the length of time

that IR/Serial data is being generated.

I/O (yellow): Light when the rear I/O channels 1 - 8 are active. The LED for each I/O port

reflects the state of that particular port.

NetLinx Control

Card Slots 1 - 4:

Accepts up to 4 compatible NetLinx Cards (NXC-COM2, NXC-IRS4,

NXC-I/O10, NXC-REL8).

Rear Panel Components:

RS-232/422/485

(Ports 1 - 7):

7 RS-232/422/485 control ports using DB9 (male) connectors with XON/

XOFF (transmit on/transmit off), CTS/RTS (clear to send/ready to send),

and 300-115,200 baud.

ICSNet: 2 RJ-45 connectors for ICSNet interface (provided by optional ICSNet

daughter card).

ICSHub Out: RJ-45 connector provides data to a Hub connected to the Controller

(provided by optional ICSNet daughter card).

Relay (Port 8): • 8-channel single-pole single throw relay ports

• Each relay is independently controlled.

• Supports up to 8 independent external relay devices

• Channel range = 1-8

• Each relay can switch up to 24 VDC or 28 VAC @ 1 A

• Two 8-pin 3.5 mm mini-Phoenix (female) connectors provide relay

termination

Digital I/O

(Port 17):

8-channel binary I/O port for contact closure with each input being capable

of voltage sensing. Input format is software selectable with interactive

power sensing for IR ports.

Note: The I/Os are not dry closure; they are electronic switches that float at

5V when Off. Therefore, they should not be expected to work in situations

that require true dry contact (or dry closure). The I/Os do work with AMX

PC1, PC2, UPC20 and UPC20+.

IR/Serial

(Ports 9 - 16):

8 IR/Serial control ports support high-frequency carriers of up to 1.142 MHz

with each output being capable of two electrical formats: IR or Serial.

• 8 IR/Serial data signals can be generated simultaneously.

• IR ports support data mode (at limited baud rates and wiring distances).

Program Port: RS-232 DB9 connector (male) can be connected to a DB9 port on a PC.

This connector can be used with serial and NetLinx programming com-

mands, as well as other DB9 capable devices, to both upload/download

information from the NetLinx Studio program.

Configuration

DIP Switch:

Sets the communication parameters for the Program port (see Baud Rate

Settings).

ID Pushbutton: Sets the NetLinx ID (Device only) assignment for the device.

Ethernet Port: RJ-45 connector provides TCP/IP communication. This is an Auto MDI/

MDI-X enabled port, which allows you to use either straight-through or

crossover Ethernet cables.

The Ethernet Port LEDs show communication activity, connection status,

speeds, and mode information:

•SPD (speed) - Yellow LED lights On when the connection speed is 100

Mbps and turns Off when the speed is 10 Mbps.

•L/A (link/activity) - Green LED lights On when the Ethernet cables are

connected and terminated correctly, and blinks when receiving Ethernet

data packets.

AxLink Port: 4-pin 3.5 mm mini-Phoenix (male) connector that provides data and power

to external control devices. Green AXlink LED indicates the state of the

AXlink port.

Power Port: 2-pin 3.5 mm mini-Phoenix (male) connector.

CardFrame #

DIP Switch:

Sets the starting address for the Control Cards in the CardFrame. (Factory

default CardFrame DIP switch value = 0). The Control Card address range

is 1-3064.

Control Card

Connectors (1-4):

20-pin (male) connectors that connect the Control Cards and external

equipment to the CardFrame.

Operating

Environment:

• Operating Temperature: 0° C (32° F) to 50° C (122° F)

• Operating Humidity: 20% to 85% RH

• Heat Dissipation (Typical): 36.9 BTU/hr

Included

Accessories:

• 2-pin 3.5 mm mini-Phoenix (female) PWR connector (41-5025)

• 4-pin 3.5 mm mini-Phoenix (female) AXlink connector (41-5047)

• 10-pin 3.5 mm mini-Phoenix (female) I/O connector (41-5107)

• Installation Kit (KA2105-01):

8-pin Relay Common Strip

4 rack mount screws

4 washers

• 2 8-pin 3.5 mm mini-Phoenix (female) Relay connectors (41-5083)

• 2 CC-NIRC NetLinx IR Emitter Cables (FG10-000-11)

• 2 removable rack ears (62-2105-07)

Other AMX

Equipment:

• 2-pin 3.5 mm mini-Phoenix male connector (41-5026)

• CC-NSER IR/Serial cables (FG10-007-10)

• NCK, NetLinx Connector Kit (FG2902)

• STS, Serial To Screw Terminal (FG959)

• Upgrade Compact Flash (factory programmed with firmware):

NXA-CF2NI4G, 4 GB Flash Upgrade (FG2116-07)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

10/10

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-2105-06 REV: J

1. Discharge the static electricity from your body by touching a grounded metal object

and unplug all the connectors from the unit.

2. Remove the three screws by turning them in a counter-clockwise direction and remove

the front faceplate.

3. Align the edges of the card with the internal guide slots and gently slide it in all the way

until the rear edge of the card snap into place.

4. Re-secure the faceplate by inserting the three screws by turning them in a clockwise

direction and securing the front faceplate to the Controller.

5. Re-apply power and other connections as necessary.

Setting the Integrated Controllers’ Starting Card Address

The 8-position CardFrame Number DIP switch on the rear panel sets the starting address

(the device number in the D:P:S specification) for the Control Cards installed in the controller.

The Control Card address range is 1 - 3064.

The factory default CardFrame DIP switch value = 0 (All CardFrame DIP switches in the OFF

position). The formula for setting the starting address is:

(DIP switch value) + Card slot Number (1 - 4) = Card Address

For example:

A DIP switch setting of 00010101:

(0 + 0 + 0 + 96 + 0 + 384 + 1536) + SLOT # (ex:1) = 2017.

A card in slot number 1 = device address 2017.

Set the CardFrame Number DIP switch value is based on the table below.

Cycle power to the unit for approximately 5 seconds. This allows the unit to read the new

device number settings.

Wiring a Power Connection

Use a 12 VDC-compliant power supply to provide power to the Controller via the rear 2-pin

3.5 mm mini-Phoenix connector. Use the power requirements information listed in the

Specifications table to determine the power draw.

The incoming PWR and GND cable from the PSN power supply must be connected to their

corresponding locations within the PWR connector.

• This unit should only have one source of incoming power.

• Using more than one source of power to the Controller can result in damage to the

internal components and a possible burn out.

• Apply power to the unit only after installation is complete.

RS-232/422/485 Wiring Connector Information

FIG. 2 shows the pinout and wiring specification information for the rear RS-232/RS-422/RS-

485 (DB9) Device Ports. These ports support most standard serial mouse control devices

and RS-232 communication protocols for PC data transmission.

The NI-4100 uses Ports 1 - 7.

WARNING: NOT When wiring the 422/485 connections, do use pre-made 9-wire cable or

connect the wire in the cable to any connection that will not be used by the DB9 serial port.

Only use wiring that connects the needed pins.

Ethernet 10/100 Base-T Connector

The RJ-45 Ethernet connector provides 10/100 network connectivity between the panel and

the NetLinx Master (FIG. 3).

Use a standard CAT5 Ethernet cable to provide communication between the Integrated

Controller and external NetLinx devices.

Baud Rate Settings (Program Port DIP Switch)

The Program Port DIP switch is located on the rear of the device. Use this DIP switch to set

the baud rate for the Program Port, according to the settings shown in the following table.

Make sure the baud rate you set matches the baud rate on your PC's NetLinx COM Settings

before programming the unit.

Note: DIP switch 1 activates/deactivates the Program Run Disable Mode. DIP Switches 2,3,

and 4 must remain OFF at all times.

Ethernet Ports Used by the NI-4100

Preparing the NI-4100 for Serial Communication

To establish serial communication with the Controller via the PROGRAM (DB9) port:

1. Use a Serial DB9 cable (i.e. CC-COM Programming Port Cable - not included) to

connect the Controller’s Program port to a DB9 port on a PC.

2. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX Control Disc

> NetLinx Studio 2 > NetLinx Studio 2).

3. Select Settings > Master Communication Settings, from the menu bar, to open the

Master Communication Settings dialog box.

4. Click the Communications Settings button to open the Communications Settings

dialog.

5. Click the NetLinx Master radio button (from the Platform Selection section) to indicate

you are working with a NetLinx Master.

6. Click the Serial radio button (from the Transport Connection Option section) to indicate

you are connecting to the Master via a COM port.

7. Click the Edit Settings button (on the Communications Settings dialog) to open the

Serial Settings dialog and set the COM port parameters (used to communicate to the

NetLinx Master).

8. Click OK to close all dialogs and return to the main application.

9. Right-click the Online Tree Refresh System: tab entry and select the Controller

should appear in the Device Tree. If not, verify that the Serial cable is connected

properly, and that the Baud Rate settings on the Controller (set via the Program Port

DIP Switch) match the settings in NetLinx Studio.

Once Serial communication has been established, use NetLinx Studio to configure the

Controller for Ethernet Communication, as described below.

Configuring the NI-4100 for Ethernet Communication

Before continuing, complete the COM port steps above.

1. Use an Ethernet cable to connect the Controller to the LAN to which the PC running

NetLinx Studio is connected.

Note: The NI-x100 Controllers feature an Auto MDI/MDI-X Ethernet port. This provides

the option of using either a standard (straight through), or a crossover Ethernet cable

to communicate with a PC - both cable types will work.

2. Select Diagnostics > Network Address from the menu bar and enter the System,

Device (0 for a Master), and Host Name information.

3. To configure the Address:

• Use a DHCP Address by selecting the Use DHCP radio button, then click the GET IP

button (to obtain a DHCP Address from the DHCP Server), click the SET IP Informa-

tion button ( ), and then finish the process by clicking the to retain the new address

Reboot Master OK > buttons.

• Use a Static IP Address by selecting the radio button, enter the IP Specify IP Address

parameters into the available fields, then click the SET IP Information button (to retain

the pre-reserved IP Address to the Master), and then click the Reboot Master > OK

buttons to finish the process.

4. Repeat steps 1 - 5 from the previous section, but rather than selecting the Serial

option, choose TCP/IP and edit the settings to match the IP Address you are using

(Static or IP).

5. Click on the d) and press Authentication Required radio box (if the Master is secure

the User Name and Password button to enter a valid username and password being

used by the secured Master.

6. Click the OK to close all dialogs and return to the main application.

Onboard WebConsole

NetLinx Masters have a built-in WebConsole that allows you to make various configuration

settings via a web browser on any PC that has access to the Master.

The WebConsole consists of a series of web pages that are collectively called the "Master

Configuration Manager". Refer to the NI Series NetLinx Integrated Controllers WebConsole

& Programming Guide for details on the WebConsole.

Accessing the WebConsole

From any PC that has access to the LAN that the target Master resides on:

1. Open a web browser and type the IP Address of the target Master in the Address Bar.

2. Press Enter to access WebConsole for that Master. The initial view is the WebControl

page.

Additional Documentation

Additional Documentation for the N1-3100 is available at www.amx.com:

• Refer to the NXI-x100 Series Hardware Reference Guide for additional details on

Installation, Upgrading, and Wiring the NI-3100.

• Refer to the NI Series NetLinx Integrated Controllers WebConsole & Programming

Guide for detailed configuration instructions.

Position 1 2 3 4 5 6 7 8

ON position

Value 12 24 48 96 192 384 768 1536

FIG. 2 RS-232/422/485 DB9 (male) connector pinouts

FIG. 3 Layout of Ethernet LEDs

Baud Rate Settings

Baud Rate Position 5 Position 6 Position 7 Position 8

• 9600 bps OFF ON OFF ON

• 38,400 bps (default) OFF ON ON ON

• 57,600 bps ON OFF OFF OFF

• 115,200 bps ON ON ON ON

DB9 Serial Port pinouts (male connector)

Pin 2: RX signal

Pin 3: TX signal

PIN 5: GND

Pin 7: RTS

Pin 8: CTS

RS-232

Pin 1: RX -

Pin 4: TX +

PIN 5: GND

Pin 6: RX +

Pin 9: TX -

RS-422

Pin 1: A (strap to 9)

Pin 4: B (strap to 6)

PIN 5: GND

Pin 6: B (strap to 4)

Pin 9: A (strap to 1)

RS-485

SPD - Speed LED lights (yellow)

100 Mbps and turns Off when the

speed is 10 Mbps.

when the connection speed is

L/A - Link/Activity LED lights

(green) when the Ethernet

cables are connected and

terminated correctly.

Ethernet Ports Used

Port type Port # Type

• FTP 21/20 TCP

• SSH (only SSH v2 is supported) 22 TCP

• Telnet 23 TCP

• HTTP 80 TCP

• HTTPS/SSL 443 TCP

• ICSP 1319 UDP/TCP

• integration! Solutions 10500 TCP

Produktspezifikationen

Marke:	AMX
Kategorie:	Regler
Modell:	NI-4100

Brauchst du Hilfe?

Wenn Sie Hilfe mit AMX NI-4100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Regler AMX

AMX SC-N8001 Bedienungsanleitung

31 August 2024

AMX SC-N8012 Bedienungsanleitung

31 August 2024

AMX MU-1300 Bedienungsanleitung

28 August 2024

AMX MU-1000 Bedienungsanleitung

28 August 2024

AMX NXF-MINI Bedienungsanleitung

27 August 2024

AMX NetLinx NX-1200 Bedienungsanleitung

27 August 2024

AMX NXA-WAPZD1100 Bedienungsanleitung

27 August 2024

AMX AXB-232++ Bedienungsanleitung

27 August 2024

AMX AXB-DMX512 Bedienungsanleitung

27 August 2024

AMX Mio Modero R-2 Bedienungsanleitung

27 August 2024

Bedienungsanleitung Regler

Neueste Bedienungsanleitung für -Kategorien-

PCE Instruments PCE-RE100P Bedienungsanleitung

16 Oktober 2024

PCE Instruments PCE-RE21R Bedienungsanleitung

16 Oktober 2024

Thrustmaster T3PA Add-On Gaming Pedal Set Bedienungsanleitung

6 Oktober 2024

Hori Battle Pad Bedienungsanleitung

5 Oktober 2024

Saitek PS2700 Bedienungsanleitung

4 Oktober 2024

Razer Wolverine V3 Pro Bedienungsanleitung

3 Oktober 2024

Axor Citterio E 36771001 Bedienungsanleitung

1 Oktober 2024

Hori Force Feedback Truck Control System Bedienungsanleitung

1 Oktober 2024

Balam Rush Kontrol Glow G595 Bedienungsanleitung

30 September 2024

Razer Panthera Bedienungsanleitung

27 September 2024