AMX CB-TP5ib Bedienungsanleitung

AMX Flachbildschirmunterstützung CB-TP5ib

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AMX CB-TP5ib (2 Seiten) in der Kategorie Flachbildschirmunterstützung. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Installation Guide

CB-TP5i Rough-In Box for NXD-500i 5" Touch Panel

Overview

The CB-TP5i Rough-In Box (FG038-11) is an optional accessory for the NXD-500i

Modero® Wall/Flush Mount Touch Panel. The Rough-In Box allows the panel to be

mounted directly to the studs/pre-wall. The NXD-500i is contained within a plastic

outer housing or back box, and the back box attaches to the Rough-In Box.

Specifications

WARNING: In order to guarantee a stable installation of the NXD-500i, the distance

between the CB-TP5i and the outer wall surface must be a minimum of .50 inches

(1.27cm) and a maximum of .875 inches (2.22cm).

• Refer to the SP62-0038-01 diagram for detailed installation dimensions.

Pre-Wall Installation of the CB-TP5i Rough-In Box

1. Remove the rough-in box cover (A in FIG. 1) before installation of the Rough-In

Box (B). Note: the cover MUST be removed before drywall installation. The

cover may be reinstalled after drywall installation using 4-40 screws (not

included).

2. Attach the optional Back Cover for the CB-TP5i (FG038-12) if necessary, as

required by building codes. (For more information, refer to the Back Cover



Installation section on page 2.)

3. Fasten the CB-TP5i rough-in box to the stud through the holes on the Stud

Mounting tabs (FIG. 2), using either nails or screws (not provided).

4. Remove the appropriate wiring knockouts from the rough-in box to 

accommodate the cables being threaded through to the NXD-500i touch panel.

5. Thread the incoming Ethernet and USB wiring through the knockouts. Use of the

left wiring knockouts is recommended with this installation for ease of connection

of the cables to the touch panel. Leave enough slack in the wiring to 

accommodate installation of the panel.

6. Install the drywall/sheetrock before inserting the main NXD-500i device into the

CB-TP5i.

7. Cut out the opening for the NXD-500i where the wall has been placed over the

Rough-In Box. Cutting out the surface slightly smaller than what is outlined in the

installation drawings, so that you can make any necessary cutout adjustments, is

very highly recommended.

FIG. 1 CPB-TP5i Rough-In Box - Front and Back Views

CB-TP5i (FG038-11) Specifications

Dimensions (HWD) • 6.73" x 9.30" x 1.43"

• 17.09 cm x 23.62 cm x 3.63 cm

Certifications • UL 508A

Front Rear

Wiring Knockouts

Breakaway Stud

Mounting Flanges

2 locations to secure cover

after applying drywall

(8-32 x .25 screws)

3 locations to secure cover

after applying drywall

FIG. 2 CB-TP5i - Mounted to Wall Stud

Stud

Recommended Cutout for

CB-TP5i Rough-In Box

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

4/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-038-11 REV: B

CB-TP5i Top CB-TP5i Break-Away

Side of Rough-In Box

With Break-Away Flanges

Optional Back Cover

for the CB-TP5i (FG038-12)

(Only for areas where

required by building codes.)

Flange detail

Back Cover Installation

Assembly of CB-TP5i and Back Plate

Screws (80-0114-01), #4-20 x .375

CB-TP5i

Back Plate

Note: two screw holes in

flanges at top and bottom

of Back Plate, but one

screw hole per flange on

sides.

Produktspezifikationen

Marke:	AMX
Kategorie:	Flachbildschirmunterstützung
Modell:	CB-TP5ib
Breite:	131 mm
Tiefe:	86 mm
Produktfarbe:	Schwarz
Höhe:	109 mm
Abmessungen (BxTxH):	131 x 86 x 109 mm
Kompatibilität:	NXD-500i\nNXD-435\nNXD-430\nCB-TP5i