AMX ABS Bedienungsanleitung

AMX Anbaustein ABS

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AMX ABS (1 Seiten) in der Kategorie Anbaustein. Dieser Bedienungsanleitung war für 44 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

Installation Guide

ABS AxLink Bus Strip

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

3/12

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-0960-01 REV: A

Overview

With the ABS AxLink Bus Strip (FG960) experience plug-and-play wiring, a

power (PWR) status LED, and 12 VDC power inputs. Perfect for larger

wiring runs the ABS simultaneously plugs in up to 10 AxLink terminals and

connectors.

Common Application

Ideal for combining up to 10 AxLink wiring runs.

Specifications

The following table lists the specifications for the ABS Axlink Bus Strip.

Use the included double-sided tape to securely affix the unit to the surface.

Installation and Wiring

Wiring Guidelines

To determine the maximum distance allowed per gauge, use the following

formula and refer to the table below:

1.5/(Power Consumption x Resistance x 2) = Distance (feet)

Note: The maximum wiring lengths are based on a minimum of 13.5 volts

available to the ABS.Preparing/connecting captive wires

1. Strip 0.25 inch of wire insulation off all wires.

2. Insert each wire into the appropriate opening on the connector

according to the wiring diagrams and connector types described in

this section.

3. Do not tighten the screws excessively; doing so may strip the threads

and damage the connector.

Wiring

1. Connect wiring from the AXlink devices to connectors 2 through 10 on

the ABS (FIG. 2). If the power LED lights when an AXlink cable is

connected to the ABS, it indicates the AXlink cable has a local power

supply. Unless that local supply is intended to power all devices

connected to the ABS, disconnect it and insulate the wire connected

to the PWR+ terminal.

Note: All AXlink connectors on the ABS are connected together.

2. Connect the control system AXlink connector 1 on the ABS. As with

the other AXlink devices in the system, connect all four wires to the

ABS unless the Central Controller is using a local power supply.

3. Connect the system power supply to the 2-pin connector on the ABS.

The power LED should light, and all AXlink devices with PWR+

connected to the ABS should have power.

Note: If the AXlink devices have local power supplies, do not connect to the

power terminal of the ABS via the PWR+ (Red).

For additional information about the wiring distances between the ABS and

a specific AXlink device, refer to the appropriate manual.

FIG. 1 ABS Axlink Bus Strip

Specifications

Power 12 VDC, 7 A max.

Connectors Ten - 4-pin, captive-wire AXlink connectors

One - 2-pin, captive-wire power connector

LED Power indicator (Red)

Enclosure Metal with black matte finish

Dimensions (HWD) 1.14" x 12.00" x 1.27"

2.90 cm x 30.48 cm x 3.23 cm

Weight 6.70 oz (189.94 g)

Mounting Options 4" double-sided foam tape

Wiring Guidelines

Gauge Resistance

18 AWG .00639

20 AWG .0101

22 AWG .0162

24 AWG .0257

FIG. 2 ABS wiring diagram

Produktspezifikationen

Marke:	AMX
Kategorie:	Anbaustein
Modell:	ABS
Gewicht:	164.42 g
Produktfarbe:	Schwarz
Stecker:	10 x 4-pin AxLink, 1 x 2-pin
AC Eingangsspannung:	12 V
Abmessungen (BxTxH):	305 x 32 x 29 mm
Anzahl der AC-Ausgänge:	- AC-Ausgänge
Stromstärke (maximal):	10 A