Aluratek ADPM01F Bedienungsanleitung

Aluratek Messung ADPM01F

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Aluratek ADPM01F (2 Seiten) in der Kategorie Messung. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Introduction

aluratek.com

model ADPM01F

User Manual

Home Health Digital Pulse Oximeter

If you need further assistance, please contact the Aluratek support

department for troubleshooting prior to returning this device.

E-mail: support@aluratek.com

Web: www.aluratek.com/helpdesk

Local (Irvine, CA): 714-586-8730

Toll free: 1-866-580-1978

Thank you very much for your purchase! This manual is written and

complied in accordance with the council directive MDD93/42/EEC for

harmonized standards. The Manual is written for the Pulse Oximeter you

purchased. In case of modifications and software upgrades, the information

contained in this document is subject to change without notice. The Manual

describes, in accordance with the Pulse Oximeter’s features and

requirements, main structure, functions, specifications, correct methods for

transportation, installation, usage, operation, repair, maintenance and

storage, etc. as well as the safety procedures to protect both the user and

equipment. Refer to the respective chapters for details.

Please read the Manual very carefully before using this equipment. These

instructions describe the operating procedures to be followed strictly, failure

to follow these instructions can cause measuring abnormality, equipment

damage and personal injury. The manufacturer is NOT responsible for the

safety, reliability and performance issues and any monitoring abnormality,

personal injury and equipment damage due to user’s negligence of the

operation instructions.

WARNING:

• It is recommended that the Pulse Oximeter should not be applied to

the same finger for over 2 hours.

• The infrared light used in this devicecan be harmful to the eyes. Do

not stare at the at the light. (The LED display is not harmful)

• This device is not intended for treatment of any kind.

• For best results do not use with dark nail polish as it may interfere

with accurate readings.

Aluratek warrants this product against defect in material or

workmanship for from the date of purchase.1 YEAR

For more information, please visit:

https://aluratek.com/warranty-return-policy

You can register your product online at:

https://aluratek.com/product-registration

1) Insert the two batteries ensuring that the + (plus) and – (minus) terminals

are aligned correctly, and then replace the cover.

2) Open the clip as shown in Figure 4.

3) Insert the finger into the rubber cushions of the clip (make sure the finger

is in the right position)

4) Press the power button once on front panel. Please keep the finger/hand

steady during the measurement.

5) Result will be shown on the display.

The Power button has two main functions. When the device is powered off,

press the button to power it on. When the device is powered on, quick press

the button to change the display orientation of the LED display.

Fingernail should be facing up toward the LED Display

1. Safety

1.1 Instructions for Safe Operation

Check the digital pulse oximeter periodically to make sure there is no

visible damage to the product. It is recommended that the device should

be inspected once a week. Any necessary maintenance must be performed

by qualified service engineers ONLY. Do not attempt to fix or repair the

oximeter in any way.

1.2 Warnings

Explosive hazard – DO NOT use the oximeter in an environment with

concentrated flammable gases.

- DO NOT use the oximeter during an MRI or CT scan.

- DO NOT use if you are allergic to rubber.

- Disposal – Make certain your follow your local laws and regulations when

disposing of this device (including battery, plastic bags, foam and paper

boxes).

1.3 Suggestions

Keep the oximeter away from dust, excessive vibration, corrosive

substances, explosive materials, high temperature and moisture. If the

oximeter gets wet, please stop operating it until it has completely dried.

- When it is carried form extreme temperatures such as very cold

environment to warm/hot environments please do not use it immediately

allowing the product to acclimate to the new temperature for best results.

- Be careful not to scratch the surface of the LED or sensor with sharp

materials.

- High temperature or high pressure steam disinfection of the oximeter is

not permitted. Refer to User Manual in the relative chapter for instructions

on the cleaning and disinfection of the device.

- Do not have the oximeter completely submerged in any liquid. When it

needs cleaning, please wipe its surface with medical alcohol and a soft cloth.

- Do not spray any liquid directly on the device.

- When cleaning the device with water, the temperature should be lower

than 60°C (140°F)

2. Overview

The pulse oxygen saturation is the percentage of HbO2 in the total Hb in

the blood, so-called O2 concentration in the blood. It is an important

bio-parameter for respiration. For the purpose of measuring the SpOz more

easily and accurately, our company developed the Pulse Oximeter. At the

same time, the device can measure the pulse rate simultaneously. The

Pulse Oximeter features in small volume, low power consumption,

convenient operation and being portable. It is only necessary for patients to

put one of their fingers into a fingertip photoelectric sensor for diagnosis,

and a display screen will directly show measured value of Hemoglobin

Saturation and Pulse rate.

2.1 Classification:

Class II b, (MDD93/42/EEC IX Rule 10)

3. Principle and Caution

2.2 Features

Operation of the product is simple and convenient.

• The product is small and light weight (total weight is about 50g/0.11lbs

including batteries) and convenient for carrying.

• Power consumption of the product is extremely low. Two AAA batteries

can power the device continuously for an estimated 20 hours.

• The product will automatically be powered off when not in use after 5

seconds to conserve the battery life.

2.3 Major Applications and Scope of Application

The Pulse Oximeter can be used to measure human Hemoglobin Saturation

and pulse rate through the finger and indicate the pulse intensity.

The product is not suitable for use in continuous supervision of

patients. If suffering from toxicosis which caused by carbon

monoxidethe device is not recommended for use

2.4 Environment Requirements

Storage Environment

a) Temperature: - 40°C + 60°C

b) Relative humidity: <95%

c) Atmospheric pressure: 500hPa – 1060hPa

Operating Environment

a) Temperature: 10°C- 40°C/50°F-105°F

b) Relative Humidity: <75% (for best results)

c) Atmospheric pressure: 700hPa – 1060hPa

3.1 Principle of Measurement

Principle of the Oximeter is as follows: An experience formula of data process

is established taking use of Lambert Beer Law according to Spectrum

Absorption Characteristics of Reductive Hemoglobin (Hb) and Oxyhemoglobin

(HbO2) in glow & near-infrared zones. Operation principle of the instrument

is: Photoelectric Oxyhemoglobin Inspection technology is adopted in

accordance with Capacity Pulse Scanning & Recording Technology, so that

two beams of different wavelength of lights can be focused onto human nail

tip through perspective clamp finger-type sensor. Then measured signal can

be obtained by a photosensitive element, information acquired through which

will be shown on screen through treatment in electronic circuits and

microprocessor.

Figure 1 Operating Principle

Photo Detector

Emitters

3.2 Caution

1. The finger should be placed properly (see the attached illustration of this

manual, Figure 4), or else it may cause an inaccurate measurement.

2. The SpO2 sensor and photoelectric receiving tube should be arranged in a

way with the subject’s arteriole in a position there between.

3. The SpO2 sensor should not be used at a location or limb tied with arterial

canal or blood pressure cuff or receiving intravenous injection.

4. Make sure the optical path is free from any optical obstacles like

rubberized fabric.

5. Excessive ambient light may affect the measuring result. It includes

fluorescent lamp, dual ruby light, infrared heater, direct sunlight and etc.

6. Strenuous action of the subject or extreme electrosurgical interference

may also affect the accuracy.

7. Do not use enamel or other dark nail polishes or paint for more accurate results.

4. Technical Specifications

1) Display Format: OLED display

SpO2 Measuring range: 0% - 100%

Pulse Rate measuring range: 30bpm – 250bpm;

Pulse Wave display: Columniation display and the waveform display.

2) Power Requirements: 2x1.5V AAA alkaline battery (not included)

3) Power consumption: Less than 30mA

4) Resolution: 1% for SpO

2 and 1bpm for Pulse rate.

5) Measurement Accuracy: +-2% in stage of 70%-100% SpO

2, and the

meaningless when stage being smaller than 70% +- 2bpm or +-2%

(select larger) for Pulse rate.

6) Measurement Performance: SpO

2 and pulse rate can be shown correctly

when pulse-filling ratio is 0.4%. SpO

2 error is +-4%, pulse rate error is

+-2bpm or +-2%.

7) Resistance to surrounding light: The deviation between the value

measured in the condition of man-made light or indoor natural light and

that of darkroom is less then +-1%.

8) It is equipped with a function on/offpower switch. The oximeter will power

off in case no finger is the oximeter within 5 seconds to preserve battery life.

9) Optical sensor: Red light (wavelength is 660nm, 6.65mW)

Infrared (wavelength is 880nm, 6.75mW)

5. Installation

5.1 View of the Front Panel

5.2 Battery

Step 1. Refer to figure 3. And insert the two AAA size batteries properly in the

right direction.

Step 2. Replace the cover.

Please take care when you insert the batteries for the improper

insertion may damage the device.

Power buttonPulse bar

graph

Pulse waveform

Battery indicator

Pulse rate

SpO2

Figure 2 Front View

6. Operating Guide

7. Repairing and Maintenance

• Please change the batteries when low-voltage is displayed on the screen or

the device no longer powers on.

• Please clean the surface of the device before using. Wipe the device with

medical alcohol first, and then let it dry in air or clean it by dry clean fabric.

• Using the medical alcohol to disinfect the product after use, prevent from

cross infection or next time use.

• Please take out the batteries if the oximeter is not going to be used for a

long period of time.

9. Technical Support and Warranty

8. Radio and TV Interference Statement

Quick Reference Guide

Please thoroughly read the manual prior to operations of

the Pulse Oximeter:

1. Insert 2 AAA batteries (ncluded)

2. Power on

3. Insert finger

Note: If you receive a “finger out” message please reinsert

or try a different finger or thumb.

Tips: If your hands/fingers are cold or if you are wearing

dark nail polish you may not be able to get an accurate

reading. Please warm your hands/fingers and/or remove

the nail polish and try again. If the sensors are dirty you

may not be able to get a reading. Gently clean the sensor

with rubbing alcohol and try again.

- For fingers that have poor blood circulation due to being cold or for really

thin fingers best results may be yielded from the thumb.

- Do not use the device on infant or neonatal patients.

- The product is best suited for children over four years old and adults

whose weights do not exceed 300 lbs. - The device may not work for all

patients. If you are unable to achieve stable readings, discontinue use.

- During proper working conditions results should begin to be displayed

within 5 seconds. It is common for pulse and Oxygen levels to vary

during use.

- The device does not have a low-voltage alarm function, it only shows the

low-voltage, please change the batteries if the device no longer powers on.

- This does not have an alarm function. Do not use the device in situations

where alarms are required.

- It is highly recommended that the batteries be removed if the device is

going to be stored for extended periods of time of more than one month,

or else batteries may leak.

- A flexible circuit connects the two parts of the device. Do not twist, pull or

try to disassemble.

WARNING!!! This equipment has been tested and found to comply with

the limits of a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by whatever

measures may be required to correct the interference.

Figure 3 Battery Installation

Figure 4 Finger position

(palm down measurement is more accurate)

Produktspezifikationen

Marke:	Aluratek
Kategorie:	Messung
Modell:	ADPM01F
Breite:	60 mm
Tiefe:	36 mm
Gewicht:	57 g
Produktfarbe:	Weiß
Akku-/Batterietyp:	AAA
Höhe:	31 mm
Energiequelle:	Akku
Schnellstartübersicht:	Ja
Display:	LED
Anzahl unterstützter Akkus/Batterien:	2
Genauigkeit:	2 BPM
Messbereich Sauerstoffsättigung:	0 - 100 %
Messbereich Pulsfrequenz:	30 - 250 BPM