Allen & Heath RPS10 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Allen & Heath RPS10 (7 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/7
PUBLICATION AP2142
USER
GUIDE
RACK MOUNT
POWER SUPPLY
RPS10
2
Warranty
LIMITED ONE YEAR WARRANTY
This product has been manufactured in the UK by ALLEN & HEATH LTD and is warranted to be free from defects in materials
or workmanship for a period of one year from the date of purchase by the original owner.
To ensure the high level of performance and reliability for which this equipment has been designed and manufactured please read
the User Guide before use.
In the event of a failure notify and return the defective unit to ALLEN & HEATH Ltd. or its authorised agent as soon as possible
for repair under warranty subject to the following conditions:
CONDITIONS OF WARRANTY:
1. The product has been installed and operated in accordance with the instructions in the installation instructions in the User
Guide.
2. The product has not been subject to misuse either intended or accidental, neglect, or alteration other than as described in the
installation instructions in the User Guide or approved by ALLEN & HEATH Ltd.
3. Any necessary adjustment, alteration, or repair has been made by ALLEN & HEATH Ltd. or it's authorised agent.
4. The defective unit is to be returned carriage prepaid to ALLEN & HEATH Ltd. or it's authorised agent with proof of purchase.
5. Units to be returned should be packed to avoid transit damage.
These terms of warranty apply to UK sales. In other territories the terms may vary according to legal requirements.
Allen & Heath Agent:
Allen & Heath Ltd.
Kernick Industrial Estate,
Penryn,
Cornwall.
England.
TR10 9LU
Tel: 01326 372070
Fax: 01326 377097
copyright © 1995 Allen & Heath Ltd. All rights reserved.
Publication AP2142 Issue 1
IMcB 30- -1 95
Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor.
Allen & Heath Ltd shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained
in this manual.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by means, electronic,
electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express written
permission of Allen & Heath Ltd.
It is recommended that all maintenance and service on the product should be carried out by Allen & Heath Ltd. or its authorised
agents. Allen & Heath Ltd cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair
by unauthorised personnel.
3
RPS10 Power Supply
INTRODUCING THE RPS10
The RPS10 is a linear power supply which, like other linear supplies, produces DC voltages by rectifying, smoothing and
regulating AC voltages from the secondary windings of a mains transformer.
Allen & Heath mixing consoles employ a number of DC voltage supply levels in their operation and these are provided at the
output of each unit.
IMPORTANT: Please read this manual carefully before connecting your
RPS10 power supply to the mains.
This manual covers the RPS10 unit, which has been designed to conform to BS EN 60065, equivalent to IEC 65 (1985) ed 5 and
BS415 1990, with CENELEC deviations.
Precautions and Safety instructions
General Precautions
Avoid storing or using the RPS10 in conditions of excessive heat or cold, or in positions where it is likely to be subjected to
vibration, dust or moisture. Do not use any liquids to clean the exterior of the unit: a soft, dry cloth or brush is ideal.
SOLVENTS MAY CAUSE DAMAGE TO PAINT OR PLASTIC PARTS
Handling and Transport
The RPS10 is supplied in a rugged carton box. If it is necessary to move the unit any distance after installation, it is recommended
that this carton is used to protect it. Be sure to disconnect all cabling before moving. If the RPS10 is to be moved regularly (e.g.
touring) it is recommended that it is installed in a foam lined case. At all times avoid applying excessive force to any switches or
connectors.
CONFORMS TO BS EN 60065 FOR SAFETY


Produktspezifikationen

Marke: Allen & Heath
Kategorie: Nicht kategorisiert
Modell: RPS10

Brauchst du Hilfe?

Wenn Sie Hilfe mit Allen & Heath RPS10 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Allen & Heath

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-