Air King LEDAK100H Bedienungsanleitung

Air King Nicht kategorisiert LEDAK100H

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Air King LEDAK100H (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

SAVE THESE INSTRUCTIONS

www.airkinglimited.com

210572203 Rev. AB 1-23 1 of 8

Exhaust Fan with Light

Models: LEDAK50, LEDAK80, LEDAK100,

LEDAK80H, LEDAK100H

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury to person, including the following:

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer.If you have

questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-related construction.

b) Sufﬁcient air is needed for proper combustion and exhausting of

gases through the ﬂue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA) and the American Society for Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

CAUTION: FOR GENERAL VENTILATING USE ONLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

d) Ducted fans must always be vented to the outdoors.

e) This unit must be grounded.

f) To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

g) Read all instructions before installing or using exhaust fan.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, DO NOT USE THIS FAN WITH

ANY SOLID-STATE SPEED CONTROL DEVICE.

a) If this unit is to be installed over a tub or shower, it must be marked

as appropriate for the application and be connected to a GFCI (Ground

Fault Circuit Interrupter) – protected branch circuit.

b) Do not install in a ceiling with thermal insulation value greater than R40.

WARNING: DO NOT USE IN KITCHENS.

WARNING: THE DUCTING FROM THIS FAN TO THE

OUTSIDE OF THE BUILDING HAS A STRONG EFFECT

ON THE AIR FLOW, NOISE AND ENERGY USE OF THE FAN. USE

THE SHORTEST, STRAIGHTEST DUCT ROUTING POSSIBLE FOR

BEST PERFORMANCE, AND AVOID INSTALLING THE FAN WITH

SMALLER DUCTS THAN RECOMMENDED. INSULATION AROUND

THE DUCTS CAN REDUCE ENERGY LOSS AND INHIBIT MOLD

GROWTH. FANS INSTALLED WITH EXISTING DUCTS MAY NOT

ACHIEVE THEIR RATED AIRFLOW.

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and conﬁrm that all pieces are present. In addition to the exhaust

fan you should have:

1 - Grill 4 - Mounting Rails

1 - Light Assembly 1 - Lamp

1 - Damper Assembly (attached) 1 - Instruction/Safety Sheet

2. Choose the location for your fan. To ensure the best air and sound performance, it is

recommended that the length of ducting and the number of elbows be kept to a minimum, the

radius of each elbow be as large as possible for the installation, and that insulated hard ducting

be used. This fan will require at least 8" of clearance in the

ceiling or wall, and will mount through drywall up to 3/4"

thick. The fan mounts between 16" or 24" on center joists

using the 4 provided mounting rails.

3. Using a straight-blade screw driver remove the electrical

knockout from the housing (Figure 1).

4. No additional vibration deadening materials are needed

for this fan.

SECTION 2

New Construction

1. Install the rails into the mounting channel on the housing. Center the mounting channel in the

slots on the housing, then from inside the housing tighten the mounting channel screws so the

channel is securely in place.

Position the housing next

to the joist. Line up housing

so that it will be ﬂush

with the ﬁnished ceiling.

Secure the ends of the rails

with screws or nails (not

included) to the joists and

slide the housing into the

ﬁnal position (Figure 2).

SECTION 3

Existing Construction

1. Set housing in position between the joist

and trace an outline onto the ceiling

material Set housing aside (Figure 3).

and cut opening, being careful not to

cut or damage any electrical or other

hidden utilities. Install the rails into the

mounting channel on the housing. Center

the mounting channel in the slots on the

housing, then from inside the housing

tighten the mounting channel screws so the

channel is securely in place. Position the

housing in the previously cut hole so that it is ﬂush with the ﬁnished ceiling. Secure the ends of

the rails to the joists (Figure 2).

SECTION 4

Ducting

NOTE: 4" OR LARGER RIGID DUCT IS RECOMMENDED FOR BEST PERFORMANCE.

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL

BUILDING CODES.

NOTE: The ducting from this fan to the outside of the building has a strong effect on the air

ﬂow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best

performance, and avoid installing the fan with smaller ducts than recommended. Insulation around

the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not

achieve their rated air ﬂow.

1. Connect the ducting to the

fan’s duct collar (Figure 4).

Secure in place using tape

or screw clamp. Always

duct the fan to the outside

through a wall or roof cap.

It is recommended that

low restriction termination

ﬁttings be used.

2. Ensure duct joints and exterior penetrations are sealed with caulk or other similar material

to create an air-tight path to minimize building heat loss or gain and to reduce the potential

for condensation. Place/wrap insulation around duct and/or fan in order to minimize possible

condensation buildup within the duct, as well as building heat loss or gain .(Figure 5)

www.airkinglimited.com

210572203 Rev. AB 1-23 2 of 8

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE

IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL

ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL

WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

NOTE: This unit includes a side access

panel for wiring that does not require

the removal of the fan’s blower

assembly. If you choose to wire the

unit from the inside, you will need

to remove the blower assembly and

internal wiring compartment. Both

methods are equally effective.

1a. External Wire Compartment:

Remove the wire compartment

cover screw and place cover in a

secure place .(Figure 6)

1b. Internal Wire Compartment:

Remove the screws holding the

blower assembly in place and

lift assembly out of housing

(Figure 7). Remove the wire

compartment cover screw and

place the cover in a secure place

(Figure 8).

NOTE: If the fan motor plug is

connected to the fan housing

receptacle, unplug so the blower

assembly can be completely removed.

STANDARD MODELS

2a. Run wiring from an approved wall switch carrying the appropriate rating. One neutral (White), one

ground (green or bare copper), and two hot (Black, and Red leads connected to the switch, one for

each function). Secure the electrical wires to the housing with an approved electrical connector.

Make sure you leave enough wiring in the box to make the connection to the fan’s receptacle.

2b. From where you have chosen to access the fan’s junction box, connect the White wire from the

house to the two White wires from the fan. Connect one Hot (Black) wire from the wall switch

to the Black wire from the fan (this is the fan control). Connect second Hot (Red) wire from the

wall switch to the Red wire from the fan (this is the main light control). Connect the ground

wire (green or bare copper) from the house to the Green wire from the fan . Use (Figure 9)

approved methods for all connections.

Figure 6

Screw

Wire

Compartment

Cover

Figure 2

Housing

Joist

Mounting Rails

Figure 5

Insulation*

(place around and

over Fan Housing

Fan Housing

Power Cable*

Seal gaps

around Housing

Round

Duct*

Seal duct joints

with tape

Round

Elbows*

Wall Cap*

Roof Cap*

(with built-in

damper)

Keep duct

runs short

*Purchase separately

Figure 3

Joist

Figure 8

Screw Wire

Compartment

Cover

NOTE: Wire compartment conﬁguration

will be dependent on model.

Figure 9

Supply from house

Neutral (White)

Ground (Green or Bare)

Fan

Neutral (White)

Green

Hot (Black)

Red

Black

Switch

(by others)

By others

Figure 1

Ducting

Duct

Collar

Figure 4

Screws

Plug

Venturi

Figure 7

HUMIDITY SENSING MODELS

3a. For proper fan operation, the humidity sensing fan will require a 3 way switch (not included).

Run wiring between the fan and the switch location. Make sure you leave enough wiring in

each box to make the connections. At the switch box connect the Black wire from the house to

the common terminal of the switch. Connect the black wire from the fan to one of the switched

terminals on the switch. This position will energize the automatic mode and the fan will

energize upon a rise in humidity. Connect the Yellow wire from the fan to the other switched

terminal on the switch. This position will activate the Manual On feature and energize the fan.

Use approved methods for all connections.

3b. To operate the main light, run wiring from single pole switch (not included). At the switch box,

connect the Black wire from the house to the common terminal of the switch. Connect the Red

wire from the fan to the load terminal of the switch. Use approved methods for all connections.

3c. From where you have chosen to access the fan’s junction box, connect the White wire from the

house to the two White wires from the fan. Connect the ground wire (green or bare copper) from

the house to the Green wire from the fan . Use approved methods for all connections.(Figure 10)

NOTE: The fan’s receptacle wires might need to be pulled outside compartment for connection. Only

pull the three loose wires outside of compartment. Additional wires will be present.

4. Carefully tuck wires back inside wire compartment and replace wire compartment cover

securing with the screw that was removed earlier.

SECTION 6

Completing the Installation

1. Use a sealant appropriate for contact with the building materials present and for the

temperature requirements of the installation to prevent air leakage from unconditioned spaces

is recommended. If gaps between unit housing and ceiling are great, additional material

(backing rod, ceiling material) may be required.

NOTE: This fan is rated for direct insulation contact (Type IC) and it is recommended that this fan be

completely covered by insulation in order to reduce heat loss or gain to unconditioned space.

2. If the fan’s blower assembly was removed during the wiring process, reinstall the blower by

reversing the directions in in .Step 1b Section 5 Wiring

3. Connect the fan wire harness by plugging the 3 pin quick connect end into the receptacle

located on the side of the wire compartment cover. Conﬁrm that the 5 pin quick connect end

is plugged into the receptacle from the blower assembly. Connect the light wire harness by

plugging the 3 pin rectangular quick connect end into the receptacle located at the top of the

wire compartment. These cords will only ﬁt one way into the receptacles .(Figure 11)

4. Install the included

lamp into the E26

(screw base) lamp

holder (Figure 12).

www.airkinglimited.com

210572203 Rev. AB 1-23 3 of 8

5. Install the reﬂector onto the grill by placing the slots on the side of the reﬂector over the lens clips

near the center of the grill. While squeezing the middle of the reﬂector, slide it so that the plastic

notches rest under the lens clips and the reﬂector feels secure (Figure 13).

6. Install the grill (with reﬂector) by

squeezing the two ends of the springs

together and installing them up into the

slots on the fan’s housing. Push the grill

up into position (Figure 14).

7. Restore power and test your installation.

SECTION 7

Setting the Humidistat

This fan may be equipped with a humidity sensor that automatically turns the fan on when humidity

is above set point and off when humidity is at or below set point. If the fan is operating too long or not

enough, ﬁrst check to see the humidity sensor set point. In cases where the ambient humidity level of

the room rises higher than the preset level, the fan will turn on even if the room is not occupied. This

helps prevent conditions that lead to mold growth.

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE SERVICING THE UNIT.

1. To set the desired humidity level of the room, remove the grill and locate the dehumidistat dial

located on the wire compartment cover.

2. Set the dial to the relative humidity you want the fan to maintain usually between 50 & 80%.

Moist climates will require higher settings than dry climates. When the humidity level of the

room is below this setting the fan will remain off. When the humidity level rises about this

setting the fan will turn on and run until the humidity level falls below this setting.

3. Reinstall the grill and restore power.

SECTION 8

Use and Care

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE STARTING INSTALLATION.

1. Cleaning the Grill: Remove grill and dislodge reﬂector from grill by sliding the reﬂector

notches from beneath the lens clips on grill. Use a mild detergent, such as dishwashing liquid,

to clean then dry with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS.

Completely dry grill before reinstalling. Clean reﬂector using a dry cloth. Refer to instructions

in , to reinstall reﬂector and grill.Section 6 Completing the Installation

2. Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently vacuum the fan. NEVER

IMMERSE ELECTRICAL PARTS IN WATER.

CAUTION: ALLOW BULBS TO COOL BEFORE REPLACING.

3. Changing the Lamp: Disconnect power to the unit. Remove grill by pulling downward on grill

and squeezing grill springs together to release from housing . Remove Reﬂector (Figure 13)

from grill by sliding the reﬂector notches from beneath the lens clips on grill. (Figure 12).

Unscrew and remove old bulb and replace with Air King PN 5S1299727 or other ENERGY STAR

certiﬁed LED Max 18 Watt, A19, E26 (Medium) base lamp.

Figure 11 NOTE: Wire compartment conﬁguration will be dependent on model.

Figure 10

Supply from house

Neutral (White)

Ground (Green or Bare)

Fan

Neutral (White)

Green

Yellow

Hot (Black)

Red

Black

Hot (Black)

Switch

(by others)

Switch

(by others)

By others

Figure 12

Lamp Lamp Holder

NOTE: LED lamp shown

Slot

Clip

Figure 13

Figure 14

Produktspezifikationen

Marke:	Air King
Kategorie:	Nicht kategorisiert
Modell:	LEDAK100H

Brauchst du Hilfe?

Wenn Sie Hilfe mit Air King LEDAK100H benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Air King

Air King EVD Bedienungsanleitung

23 September 2024

Air King F130D Bedienungsanleitung

14 August 2024

Air King LEDAK100D Bedienungsanleitung

9 August 2024

Air King QMDB Bedienungsanleitung

6 August 2024

Air King EVLDGH Bedienungsanleitung

6 August 2024

Air King DL4D Bedienungsanleitung

2 August 2024

Air King MD624 Bedienungsanleitung

1 August 2024

Air King EVLD Bedienungsanleitung

30 Juli 2024

Air King D4S Bedienungsanleitung

30 Juli 2024

Air King BFQ70W Bedienungsanleitung

30 Juli 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024