AFX Sinclair SNS041814LAJUDSN Bedienungsanleitung

AFX Erleichterung Sinclair SNS041814LAJUDSN

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AFX Sinclair SNS041814LAJUDSN (2 Seiten) in der Kategorie Erleichterung. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

LED Indoor Luminaire Model s #

Wall Mount

120-277VAC / 60Hz

Page 1 of 1 8061158 R0

SNS041007LAJUDSN

SNS041814LAJUDSN

Limited Factory Warranty

AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years

from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due

to improper installation, misuse, mishandling or damage incurred in transit.

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal

electric shock and/or property damage.

 It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.

 Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

 This xture is designed for use in a 120-277VAC, 60Hz fused circuit. The xture is compatible with Triac (forward-phase or leading edge) / ELV (reverse phase or trailing edge) and

0-10 V dimmers. Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground

wire (green) contact between this xture and the ground connection of your main power supply panel.

 This xture is intended to be used for general indoor lighting in dry or damp locations.

 Disclaimer

Changes or modications not expressly app has been roved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES- -005 (B). These limits are designed to 005 (B) / NMB

provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult with the dealer or an experienced radio/TV technician for help.

Any modications to this xture may void the warranty and interfere with the safe operation of the luminai re.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Assembly Instructions

1. Preparing for installation.

A. vicing any part of this xture. Disconnect electrical power before installing or ser

B. Remove fixture from carton; remove components from hardware kit.

C. This xture requires handy box (2x4) not included for installation. –

D. Place the diuser assembly (5) and hardware o to the side.

E. Install mounting bracket (1) to the handy box (not included) with two screws (2 ).

2. Wiring.

All wiring must take place inside junction box. Caution: Make sure power is o at fuse or

circuit breaker box. Check power wires for damage or scrapes. If the power supply wires are

within three inches of the driver, use a wire suitable for at least 90C (194F). Most Note:

dwellings built before 1985 have supply wire rated to 60C. Consult a qualied electrician before

installing.

A. This unit will not operate properly unless connected to a “grounded” electrical circuit.

Electrical shock, overheating, low or no light output, and shortened LED life can result if

proper grounding is not done. Securely attach power source ground wire and xture

ground wire to green ground screw on circular mounting bracket.

B. Make all wire connections to appropriate wire. Secure with wire nuts (provided).

C. For non-dimming xture. Fixture will operate normal w/o connection to any dimmers.

C white xture lead to white (N) wire from supply power source. Connect black onnect

xture lead to black (L) wire from supply power source. Gray and purple wires are not to

be used and must be individually capped to prevent shorting.

D. Connect white xture lead to (N) wire from dimming source For TRIAC dimming. per

dimmer wiring instructions. Connect black xture lead to black (L) wire from dimmer

supply power source. Gray and purple wires are not to be used and must be individually

capped to prevent shorting.

E. For -10V) dimming xture(0 . Connect gray wire from the xture to the dimmer source

gray wire. Connect purple wire from the xture to the dimmer source purple wire. Connect

white xture lead to white (N) wire from supply power source. Connect black xture lead

to black (L) wire from dimmer supply power source.

F. Do not mix wires. Pull on each wire lead to make sure connections are secure. Make

certain no bare wires are exposed outside of wire connectors. Tuck all connections neatly

into junction box.

3. Fixture housing installation.

A. Install the xture housing (3 by aligning holes to mounting bracket (1) then secure with two nuts (4). ) two

4. Color Changing Temperature Adjustment, CCT (if desired).

A. Ad just the two switches on each accordingly to the desired color temperature as seen below. All boards must be set the same way. board

Note: Fixture is preset to 3500K from factory.

5. Diuser installation.

A. Install the diuser (5) sliding over the front bracket and aligning top hole the xture housing then secure with screw (6). Note: Do not over tighten the screw as it may cause by to

diuser to crack or bow.

6. Power to the xture can now be restored.

SNS041007LAJUDSN

MODEL SHOWN

HANDY BOX

(NOT INCLUDED)