AEG WS 700-125 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für AEG WS 700-125 (57 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/57
WS 700-100, WS 700-115, WS 700-125,
WSE 700-115
Instruction for use
Please read and save these instruction
Gebrauchsanleitung
Bitte lesen und aufbewahren
Instruction d’utilisation
Prière de lire et de conserver
Istruzioni duso
Si prega di leggere le istruzioni e di conservarle
Instrucciones de uso
Lea y conserve estas instricciones por favor
Instruções de serviço
Por favor leia e conserve em seu poder
Gebruiksaanwijzing
Lees en let goed op deze advizen
Brugsanvisning
Vær venlight at læse og opbevare
Bruksanvisning
Vennligst les og ta godt vare på denne informasjonen
Bruksanvisning
Var god läs och tag tillvara dessa instruktioner
Käyttöohje
Lue ja sä öilyt
ENGLISH # WS 700-100, WS 700-115, WS 700-125, WSE 700-115
Introduction You demand the best and buy quality - quality provided by Atlas Copco. We have
built for you a reliable and lasting tool. Working effectively and without endangering
your health is only possible if this instruction for use is read carefully before first us-
ing the tool. We want to satisfy our customers and would like you to buy again AEG
Electric Power Tools from Atlas Copco.
Technical Data
Safety advice Please note safety instructions on red sheet 4 000 333 024!
Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
Always pull the plug from the mains before making any settings or carrying out main-
tenance.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
Before use check machine, cable, and plug for any damages or material fatigue. Re-
pairs should only be carried out by authorised service agents.
After switching off, the machine will not be idle immediately. (After-running of the
work spindle.) Allow the machine to come to a stop before putting down.
Never reach into the danger area of the machine when it is running.
Always wear safety goggles and ear protectors when working with this machine. It
is further recommended to wear safety gloves, apron, as well as sturdy non-slipping
shoes.
Always use the additional handle.
Always use the protecting cap when roughing-down and separating.
Only use tools whose permitted speed is at least as high as the highest no-load
speed of the machine.
Pay attention to the dimensions of the grinding disc. The mounting hole diameter
must fit the mounting flange without play. Do not use reducer pieces or adapters.
Check grinding tools before use. The grinding tool must be properly mounted and
turn freely. Perform a test run for at least 30 seconds without load. Do not use dam-
aged, out of round or vibrating grinding tools.
Immediately switch off the machine in case of considerable vibrations or if other mal-
functions occur. Check the machine in order to find out the cause.
Always use and store the grinding disks according to the manufacturers instruc-
tions.
When grinding metal, flying sparks are produced. Take care that no persons are en-
dangered. Because of the danger of fire, no combustible materials should be locat-
ed in the vicinity (spark flight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust flying from the workpiece
come into contact with you.
Type WS 700-100 WS 700-115 WS 700-125 WSE 700-115
Nominal power (W) 710 710 710 710
Min. no-load speed (min-1) 2700
Max. no-load speed (min -1 ) 11000 10000 10000 10000
Grinding disk diameter (mm) 100 115 125 115
Thread of work spindle M10 M14 M14 M14
Weight (kg) 1.6 1.6 1.6 1.6
Speed control –––
No-load speed limiter –––
Smooth start –––
ENGLISH # WS 700-100, WS 700-115, WS 700-125, WSE 700-115
Dust that arises when working in stones with crystalline silicic acid can damage your
health. Do not work on any material containing asbestos. Please note the safety reg-
ulations, VBG, of the employers liability insurance association.
Never use a cutting disc for grinding. Do not subject cutting discs to side pressure.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work with the machine.
The workpiece must be fixed if it is not heavy enough to be steady. Never lead the
workpiece to the grinding disk with your hand.
In case of extreme operating conditions (e.g. when smoothing metals with the sup-
porting disk and vulcanised fibre disks) strong contamination can build up inside the
angle grinder. In such cases it is recommended to shorten the cleaning cycles and/
or add a residual current operated device.
Measured
sound value
Typically the A-weighted noise levels of the tool are:
Sound pressure level = 85 dB (A).
Sound power level = 98 dB (A).
Wear ear protectors!
Measured
vibration value
Typically the weighted acceleration is 5 m/s 2.
Usage This angle grinder can be used for separating and grinding many different materials,
e.g. metal or stone. In case of doubt please read the manufacturers instruction.
Do not use this product in any other way as stated for normal use.
Mains
connection
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is pos-
sible as the appliance features protective insulation to DIN 57 740/ VDE 0740 and
CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is con-
nected to the plug terminal marked L or coloured red, and the blue (neutral) wire of
this appliance is connected to the plug terminal marked N or coloured black. Under
no circumstances must the wires of this appliance be connected to the earth termi-
nal of the plug marked either E, with the earth symbol, or coloured green or green/
yellow.
Smooth start
(WSE 700-115)
The electronic smooth start will prolong the life of both the motor and the gears.
Switching on
and off
Switching on: Push the sliding switch forward. To
lock, depress the front part of the switch.
Switching off: To unlock, depress the back part
of the sliding switch. The switch will automatically
move back to “ ”O .
1
2


Produktspezifikationen

Marke: AEG
Kategorie: Nicht kategorisiert
Modell: WS 700-125

Brauchst du Hilfe?

Wenn Sie Hilfe mit AEG WS 700-125 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert AEG

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-