ACTi Q450 Bedienungsanleitung

ACTi Überwachungskamera Q450

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für ACTi Q450 (2 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Q450 Multi-Imager Bullet Camera Quick Guide
This guide is for quick installing connecting the Q450 Multi-Imager Bullet Camera For more details, please refer and .
to the User s Manual. ’
Installation Notices
This camera must be installed by qualified personnel and the installation should conform to all local codes.
Do not replace batteries of the camera. Risk of explosion may occur if the battery is replaced by an incorrect type.
To use an external power supply, please contact the camera manufacturer to confirm that the power supply uses
the same power specifications as the camera. The power supply must comply with the LPS requirements.
All- -One Cable in
No
Cable
Pin
Definition
Remarks
1
RJ- 45
-
For network and PoE connections
2
Audio I/O
Green
Audio Out / Mic Out (Line Out)
Two-way audio transmission
Pink
Audio In / Mic In (Line In)
3
Alarm I/O
(5-pin Terminal Block)
1
Alarm In 2+
Alarm connection
#Do connect external NOT
power supply to the alarm I/O
connector of the IP camera.
2
Alarm In -
3
Alarm In 1+
4
Alarm Out -
5
Alarm Out +
4
Power (AC 24V)
(2-pin Terminal Block)
1
AC 24V 1
Power connection
2
AC 24V 2
microSD Card Slot / Default Button
T positions of microSD card slot and reset button are shown below. For details about how to detach the he as
camera’s front housing, please refer to section microSD Card Slot / Reset Button in the User’s Manual.
microSD Card Slot
Insert the microSD card into the card slot to store videos and snapshots. Do not remove the microSD card when the
camera is powered on.
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
support long term continu s data read/write. Please contact the manufacturer of the microSD card for ou
information regarding the reliability and the life expectancy.
Reset Button
Press the reset button with a proper tool for at least 20 seconds to restore the system.
Camera Cabling
Please follow the instructions below for cable connections.
Power Connection
Please use an AC 24V adaptor and connect it to the 2-pin terminal block of the All- -One cable and the power outlet. in
Alternatively, connect the Ethernet cable to the -45 connector of the All- -One cable and plug the other end of the RJ in ,
cable to a Power Sourcing Equipment (PSE) switch.
Ethernet Cable Connection
Connect one end of the Ethernet cable to the - connector of the All- -One cable, and plug the other end of the RJ 45 in
cable to the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the
PC.
NOTE: Check the status of the link indicator and the activity indicator LEDs. If the LEDs are unlit, please
check the LAN connection.
NOTE: The ITE is to be connected only to PoE networks without routing to the outside plant or equivalent
description.
Before Login to the Camera
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and plug-ins or
setting Internet’s security level to default. For further details, please refer to the User s Manual. ’
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click <Internet Options >.
Step 3: Click the <Security> tab and select <Internet>,
and click <Custom level> to change ActiveX
settings.
Step 4: Set ActiveX controls and plug-ins items to “ ”
<Prompt> or <Enable>.
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click <Internet Options >.
Step 3: Click the <Security> tab and select <Internet>.
Step 4: Down the page, click Default Level and click “ ”
< > to confirm the setting. Close the browser OK
window, and open a new one later for
accessing the IP camera.
V20200828
Camera Login
The default IP address of the camera is: 192.168.0.100. Therefore, to access the camera for the first time, please set
the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.99
Subnet Mask: 255.255.255.0
Login ID and Password
Key in the camera IP address on the URL bar of the web browser and hit Enter“ ”.
For initial login, use the default username: admin“ ” and then setup the password. Follow the on-screen instructions
to do so. This username and password will be used for succeeding login. Note that the username and password
are case sensitive.
Default Username: admin Password: (user must set up first)
Install the ActiveX Control
After connecting to the camera, the request for installing the ActiveX control will appear jus below the URL bar. t
Right click on the information bar, and then click on <Install ActiveX Control > to permit ActiveX control …
installation.
In the pop-up security warning window, click on <Install> to start downloading the software on the PC.
Click on <Finish> after installation is completed.
Browser-based Viewer
The main page of the IP camera user interface is shown as the figure below. Please note that function buttons will
vary depending on the camera model.
Q450
Multi-Imager Bullet Camera
Quick Guide
Ver. 1.1

Produktspezifikationen

Marke: ACTi
Kategorie: Überwachungskamera
Modell: Q450

Brauchst du Hilfe?

Wenn Sie Hilfe mit ACTi Q450 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Überwachungskamera ACTi

ACTi

ACTi Z954 Bedienungsanleitung

29 August 2024
ACTi

ACTi Z411 Bedienungsanleitung

28 August 2024
ACTi

ACTi Z715 Bedienungsanleitung

24 August 2024
ACTi

ACTi Z75 Bedienungsanleitung

24 August 2024
ACTi

ACTi Z315 Bedienungsanleitung

24 August 2024
ACTi

ACTi Z73 Bedienungsanleitung

24 August 2024
ACTi

ACTi E58 Bedienungsanleitung

21 August 2024
ACTi

ACTi A313 Bedienungsanleitung

21 August 2024
ACTi

ACTi B97A Bedienungsanleitung

19 August 2024
ACTi

ACTi B913 Bedienungsanleitung

18 August 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024
D-Link

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024
Foscam

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024
Alecto

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024
Hikvision

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024