4ms Pod 34X Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr 4ms Pod 34X (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Pods
Compact Eurorack Enclosures from 4ms Company
Usage Guide 3.0 – October 7, 2019
4ms Pods are low-cost, portable, compact enclosures that turn Eurorack modules into table-top
instruments. Pods come with an integrated power supply which allows you to daisy-chain multiple
units in different configurations using only a single power brick.!
Overview
!
M3 threads
(Screws included)
Additional Barrel jack
For daisy-chaining Pods
Four Eurorack power headers
(Pod34X, 40X, 48X, 60)!
Six Eurorack power headers
(Pod 64X)
Two Eurorack power headers
(Pod20, Pod26, Pod32)
Available in 20HP, 26HP, 32HP, 34HP, 40HP, 48HP, 60HP, 64HP
Barrel jack
15-20VDC power input
Pod 34X/64X: 55mm (2.16”)
Pod40X/48X: 50mm (1.97”)
Other Pods: 34mm (1.34”)
Maximum module depth
-12V
+5V
Headers
Pod20/26/32
0.28A
0.2A!
2
Pod34X
0.67A
1.0A!
4
Pod40X/48X/60
0.67A
0.5A!
4
Pod64X
0.67A
1.0A
6
Installing a module
Congratulations on your purchase of a Pod! It’s easy to install a
standard Eurorack module in a Pod:!
(1) Unplug all any barrel cables power brick cables from the Pod.!
(2) Attach your module’s power ribbon cable to a 16-pin power
header on the Pod. "
The Pod power header is keyed so that the cable cannot be
inserted upside-down. The red stripe should be down, and
should connect to the -12V on the module.
(3) Connect the other end of the ribbon cable to your Eurorack
module (unless it's already be attached, of course!)!
(4) Place the module into the Pod so that all screw holes on the module’s faceplate line up with the
screw holes on the Pod.!
(5) Use M3 screws (included with Pod) to secure the module’s faceplate to the Pod.!
(6) Repeat steps 2-5 to install more modules. If you need to install more modules than there are power
headers, you can use a Multi Power Cable.!
(7) Power on the Pod by plugging a power brick into either
one of the jacks on the back of the Pod. "
Or, if you already have another Pod that’s receiving
power, you can daisy-chain the new Pod using a barrel
cable.
(8) Optional: you may attach the included adhesive rubber
feet to the bottom of your Pod. To use Pods on a
pedalboard, you may attach Velcro or hook-and-loop
fastener instead (not included)"
Power
The Pod20, Pod26, and Pod32 have an integrated power supply with two standard Eurorack power
headers; the Pod 34X, Pod40X, Pod48X, and Pod60 feature four power headers, and the Pod64X has
size. All Pods work with all modules that use 10 and/or 16-pin power cables.
Power Bricks
To supply power to a single Pod, plug a Power Brick (sold
separately) to either one of the jacks on the back of the
Pod. Wherever Pods are sold, you can purchase a Power
Brick that’s compatible with the Pods. You also can use
the Power Brick sold for use with the Row Power system
(90W Brick). Or you can use your own power brick as long
as it meets these specifications:!
•Voltage: 15VDC to 20VDC (15VDC for best
efficiency)!
•Style: 2.1mm positive tip barrel plug (5.5mm outer
diameter)!
•Wattage or amperage: Most modern power bricks
will be able to power 6 or more daisy-chained
Pods, but anything under 15W (about 1A) will
probably not be sufficient for powering more than
one or two Pods.!
Page of 2 4
Warning: If a screw seems to be unusually
tight or pointing at an angle other than
vertical, back it out and try again. The
threads on the Pod’s screw holes can be
permanently damaged by forcing a screw
that’s the wrong size or installed at an
angle.
Multi Power Cables
If you need to install more modules than the
number of power headers in your Pod, you
can use a Multi Power Cable, available
wherever Pods are sold. One end plugs into
the power header on the Pod, and the other
connectors plug directly to modules. Each
Multi Power Cable can power three modules
from one power header. Multi Power Cables
come in two varieties: 10-pin, and 16-pin.
Choose the one that matches the type of
power cable on your modules.
Daisy-chaining
Pods are meant to be daisy-chained. When you plug a
Power Brick into one of the jacks on the back of a Pod,
the other jack can be used to power an additional Pod.
Simply connect a Barrel Cable from one Pod to the next.
You can continue to daisy-chain Pods to make long
chains! With the 45W Power Brick sold for use with
Pods, 8 or more Pods can be daisy-chained (depending
on the total power consumption of all the modules). !
!
Unpowered Pods
Most Pods are sold with a power supply. Pods can also be sold “Unpowered”: essentially an empty
metal box perfectly sized for Eurorack modules.!
If you purchased an Unpowered Pod, you’ll see there are no power headers or jacks on the back. You
will need to provide your own power supply for your modules. If you have a Row Power module, it can
be installed on the top of the Pod as a normal module. Additionally, there are two holes on the back of
the Unpowered Pod which are plugged with a plastic insert: you can use these holes to mount a jack
which connects to your own DIY power supply.!
Tips
•Pods use M3 screws (which are included). You may use any other M3 screw, such as Befaco
Knurlies, but do not use screws with other thread sizes to avoid permanently damaging the threads
of the Pod.!
•The Pod40X and Pod48X series have 1.97” (50mm) of depth on the inside; the Pod34X and 64X
have 2.16” (55mm); and the thin Pods (Pod20/26/32/60) have 1.34” (34mm) of depth on the inside.
The depth of your module, including the power header, must be less than or equal to this.!
•Exceeding the maximum power draw for a Pod may cause modules to function poorly (or not at all).
It’s possible that exceeding the maximum ratings may damage your modules (this is true for any
power supply).!
Page of 3 4
Barrel Cables
Barrel Cables are used to daisy-chain Pods.
These same cables can be used in the Row
Power system: You can even daisy-chain a Pod
and a Row Power together!
Never plug more than one power brick
into a Pod or a chain of Pods!


Produktspezifikationen

Marke: 4ms
Kategorie: Nicht kategorisiert
Modell: Pod 34X

Brauchst du Hilfe?

Wenn Sie Hilfe mit 4ms Pod 34X benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert 4ms

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-