3M 1700 Bedienungsanleitung

3M Videostrahl 1700

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für 3M 1700 (9 Seiten) in der Kategorie Videostrahl. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/9
Ré ec etr r jop o t ur
Manu d op a uel e l’ ér te r
Ta es c eg li h p ot r j k ot r
Be e edi nung ans l itung
Re ectr rop oy t ro
Manua d op adol el er r
L La a a v gn u nomi sa
Manua d ole ’Us
Ov h dp o k oer ea r je t r
Br s suk anvi n ngi
Ov h dp o oer ea r j tec r
Hand d ngl ie i
Re etr r jop o t ro
Manua do u uá ol s ri
Ove head P o ec or r j t r
Ope a ng n uc onr ti I s rt ti s
1700
3M 1700 Operator’s Guide 1
Main Menu
INTENDED USE
Before operating the machine, please read the entire manual
thoroughly. The 3M™ Overhead Projector 1700 was
designed, built and tested for use indoors, using 3M brand
lamps and nominal local voltages.
The use of other replacement lamps, outdoor operation or
different voltages has not been tested, and could damage the
projector or peripheral equipment and/or create a potentially
unsafe operating condition.
IMPORTANT SAFEGUARDS
When using your overhead projection equipment, basic
safety precautions should always be followed, including
the following:
1. Read and understand all instructions before using.
Pay particular attention to areas where this symbol
! is shown.
2. Close supervision is necessary when any appliance
is used by or near children. Do not leave appliance
unattended while in use.
!3. Care must be taken as burns can occur from
touching hot parts.
4. Do not operate appliance with a damaged cord or if
the appliance has been dropped or damaged until it
has been examined by a qualified service
technician.
!5. Position the cord so that it will not be tripped over,
pulled, or contact hot surfaces.
6. If an extension cord is necessary, a cord with a
current rating at least equal to that of the appliance
should be used. Cords rated for less amperage
than the appliance may overheat.
7. Always unplug appliance from electrical outlet
before cleaning and servicing and when not in use.
Never yank cord to pull plug from outlet. Grasp plug
and pull to disconnect.
!8. Let appliance cool completely before putting away
or when replacing lamp.
9. To reduce the risk of electric shock, do not
immerse this appliance in water or other liquids.
10. To reduce the risk of electric shock, do not
disassemble this appliance, but take it to a
qualified technician when service or repair work is
required. Incorrect reassembling can cause electric
shock when the appliance is used subsequently.
11. The use of an accessory attachment not
recommended by the manufacturer may cause a
risk of fire, electric shock, or injury to persons.
12. Do not overload accessory circuit (if equipped).
13. Connect this appliance to a grounded outlet.
14. Disconnect this unit from its source of supply
before replacing the projection lamp.
!15. This unit is equipped with optical lenses and
should not be exposed to direct sunlight.
16. Keep ventilation openings free of any obstructions.
17. This unit is connected by a special power cord that,
if damaged, has to be replaced by the same type
of power cord. This part can be ordered from your
local 3M dealer and has to be installed by a
qualified service technician.
SAVE THESE INSTRUCTIONS
The information contained in this manual will help you
operate and maintain your Overhead Projector.
THANK YOU
Thank you for choosing 3M overhead projection equipment.
This product has been produced in accordance with 3M’s
highest quality and safety standards to ensure a smooth and
troublefree use in the years to come. Your purchase of this
product proves that you appreciate this.
For optimum performance we kindly ask you to follow these
operating instructions carefully. We hope you will enjoy using
this high performance product in your meeting, training and
presentation sessions.
Part Identification List
1. Open Projection Head
2. Projection Mirror
3. Singlet Lens (1705, 1708)Triplet Lens (1720, 1750)
4. Arm
5. Focus Knob
6. Post
7. Post Latch
8. Post Cradle
9. On/Off Power Switch
10. High/Low Brightness Switch (1708, 1720, 1750)
11. Color Tuning Knob (1708, 1720, 1750)
12. Lamp Changer (1708, 1720, 1750)
13. Top Cover Release Latch (with interlock)
14. Top Cover Stage Glass
15. Cord Storage
16. Power Cord
17. Machine Identification Plate
2 3M 1700 Operator’s Guide
Main Menu
Set Up Projector
1. Raise the post (1) until it locks into place.
2. Raise projection mirror (2) to adjust screen elevation.
3. Remove power cord (3) from storage area.
4. Plug in power cord into projector and wall outlet (4) and
depress on/off power switch.
Operating The Projector
Read the Important Safeguards before operating this
projector.
Caution!
Do not illuminate lamp with projection mirror in the closed
position. Heat from the lamp may produce parts that are hot
to the touch and damage the optics.
1. Push power switch “ ON” to illuminate lamp.
|= ON
O = OFF
2. Rotate projector (1) until projected light beam is
perpendicular (90°) to the screen surface. The height at
the left and right sides of the projected image should be
equal.
3. Adjust angle of projection mirror (2) to raise or lower the
image on the screen.
4. For best results, tilt projection screen (3) toward
projector until the width of the projected image is equal
at both the top and bottom.
5. Place LCD projection panel or film transparency in the
center of stage glass (4).
6. Set lamp brightness to “ “High” or Low” position. See
“ High/Low Lamp Control” below.
7. Rotate focus knob (5) for sharpest image.
8. If yellow/orange or blue colors appear in corners of
image, rotate color tuning dial to remove colors. See
Color Tuning.
Fold Down Projector
1. Depress ON/OFF power switch, then unplug power cord
from outlet. Coil cord into cord storage area.
2. Close projection mirror.
3. Rotate focus knob (1) clockwise to raise projection head
to maximum position.
4. Release post latch (2) and lower post until it locks in the
post cradle.
5. Rotate focus knob (3) counterclockwise to lower head
until it stops.
6. To move the projector, lift it from the bottom.

Produktspezifikationen

Marke: 3M
Kategorie: Videostrahl
Modell: 1700

Brauchst du Hilfe?

Wenn Sie Hilfe mit 3M 1700 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Videostrahl 3M

3M

3M 1895 Bedienungsanleitung

26 Mai 2024
3M

3M MP8640 Bedienungsanleitung

10 Mai 2024
3M

3M S10C Bedienungsanleitung

26 April 2024
3M

3M MP225 Bedienungsanleitung

25 April 2024
3M

3M X30 Bedienungsanleitung

10 April 2024
3M

3M X90 Bedienungsanleitung

7 April 2024
3M

3M X80 Bedienungsanleitung

22 März 2024
3M

3M MP410 Bedienungsanleitung

2 März 2024
3M

3M MP7720 Bedienungsanleitung

10 Februar 2024
3M

3M 1825 Bedienungsanleitung

7 Februar 2024

Bedienungsanleitung Videostrahl

Neueste Bedienungsanleitung für -Kategorien-

Eurolite

Eurolite LED THA-40PC Bedienungsanleitung

13 August 2024
Acer

Acer P5290 Bedienungsanleitung

9 August 2024
EKO

EKO KPS1080WP Bedienungsanleitung

9 August 2024
Mitsubishi

Mitsubishi XD400U Bedienungsanleitung

25 Juni 2024
Mitsubishi

Mitsubishi EX100U Bedienungsanleitung

25 Juni 2024
Mitsubishi

Mitsubishi PK20 Bedienungsanleitung

25 Juni 2024
Mitsubishi

Mitsubishi HL2750U Bedienungsanleitung

25 Juni 2024
Mitsubishi

Mitsubishi SD510U Bedienungsanleitung

25 Juni 2024
Mitsubishi

Mitsubishi WD510U Bedienungsanleitung

25 Juni 2024
Mitsubishi

Mitsubishi EX241U Bedienungsanleitung

25 Juni 2024