Zanussi ZHT61X Bedienungsanleitung

Zanussi Dunstabzugshaube ZHT61X

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Zanussi ZHT61X (3 Seiten) in der Kategorie Dunstabzugshaube. Dieser Bedienungsanleitung war für 38 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

04306315 - K196 Zan-El

INSTRUCTIONS FOR USE

COOKER HOOD

ZHT 61

ZHT 91

DECORATIVE PIPE

CZ 71

WARNING

---------------------------------------------------

The distance between the hob and the lower

part of the hood must be at least 65 cm.

The air collected must not be conveyed into

a duct used to blow off smokes from ap-

pliances fed with an energy other than

electricity (central heating systems, ther-

mosiphons, water-heaters, etc.).

Comply with the official instructions provided

by the competent authorities in merit when

installing the disposal duct. In addition,

exhaust air should not be discharged into a

wall cavity, unless the cavity is designed for

that purpose.

The room must be well aerated in case a

hood and some other heat equipment fed

with an energy other than electricity (gas, oil,

coal heaters, etc) operate at the same time.

In fact the intake hood, disposing of air, could

create a vacuum in the room. The vacuum

should not exceed 0,04mbar. This prevents

the gas exhausted by the heat source from

being intaken again. It is therefore advisable

to ensure the room contains air taps able to

ensure a steady flow of fresh air.

This appliance has such technical parti-

culars that it belongs to class II in-

sulation, therefore it must not be earthed.

When making the electrical connections,

check that the voltage values correspond to

those indicated on the data plate inside the

appliance itself.

In case your appliance is not furnished with

a non separating flexible cable and has no

plug, or has not got any other device ensu-

ring omnipolar disconnection from the elec-

tricity main, with a contact opening distance

of at least 3 mm, such separating device

ensuring disconnection from the main must

be included in the fixed installation.

Always switch off the electricity supply be-

fore carrying out any cleaning or servicing

operations on the appliance.

USE

--------------------------------------------------

Avoid using materials which could cause

spurts of flame (flambÈes) near the ap-

pliance.

When frying, take particular care to prevent

oil and grease from catching fire. Already

used oil is especially dangerous in this re-

spect. Do not use uncovered electric grates.

To avoid possible risks of fire always comply

with the indicated instructions when cleaning

anti-grease filters and when removing grease

deposits from the appliance.

MAINTENANCE

--------------------------------------------------

Thorough servicing guarantees correct and

long-lasting operation.

Use lukewarm water and neutral detergent

to clean painted appliances. Never use

products containing abrasives.

Take great care to prevent the use of corro-

sive or abrasive products when cleaning

steel, copper or brass appliances. It is

advisable to use specialized products

according to the manufacturerís instructions.

DESCRIPTION

--------------------------------------------------

The appliance can be used both in Ducting version

and Filtering version.

In the Ducting version (Fig. 1), cooking vapours

and/or odours are conveyed straight outside

(ceiling and/or wall) by a disposal duct, using the

holes that are predisposed on the top and/or at the

back of the apparatus.

In the Filtering version (Fig. 2) cooking vapours

and/or odours are depurated by a special activated

vegetal charcoal fiber panel and recirculated

around the room by the front fissures. ATTENTION:

For the filtering version it is absolutely necessary

to use the special active vegetal charcoal fiber

panel whereas for the ducting version it is not.

INSTALLATION

--------------------------------------------------

Before assembling the appliance it is necessary to

take off the anti-grease grille. To take off the grill

it is necessary to push this one towards the rear of

the apparatus, by means of the proper knobs, so

that it gets released, and to pull it downwards; to

take it off completely, make it rotate on one side

keeping the other one steady (Fig. 3).

For the ducting installation of the appliance, connect

one of the two discharge outlet to the external

ducting and seal the other opening with the supplied

cap (Fig. 4). For the filtering installation you must

close both the discharge outlets of the apparatus

using the supplied caps.

The following operations are essential for assembly:

ñ Install a proper wiring system.

ñ If your apparatus is to be assembled as a

Ducting appliance, you must first make the air

venting hole and get a proper pipe to connect

the hole to the flange of the hood.

Wall fitting

Making use of the appropriate drilling jig, apply the

supplied blocks into the wall. Insert two of the

supplied screws so that the apparatus can be

hooked onto these ones by means of the holes

provided on the appliance (Fig. 5A). Once the

apparatus is hooked, fix it definitively to the wall

using the two other screws and the holes made at

its bottom (Fig. 5B). To avoid damage make

exclusive use of the holes already prepared on the

hood. Make the electrical connections.

Wall cupboard fitting

Using the appropriate drilling jig make the four fixing

holes into the bottom of the wall cupboard and cut

the air venting hole if the hood is a ducting version

one (for the filtering version this hole is not

necessary). Holding the hood against the bottom

of the cupboard fix it to it by means of the supplied

four screws (Fig. 6). Make the electrical

connections.

IMPORTANT:

Check the position of screw A (Fig. 8). For the

ducting version screw A must be completely

screwed; for the filtering version the screw

must be completely unscrewed to let the sucked

air to get out through the top fissures.

ASSEMBLY OF THE DECORATIVE PIPE

AVAILABLE AS ACCESSORY

--------------------------------------------------

Fix the lower bracket A onto the apparatus (Fig.

9). Fix the upper bracket B onto the ceiling; in

order to position the bracket on the same axis

as your apparatus, refer to the small triangle C

that is on the central axis. Take the two telescopic

pipes minding that you have to lift slightly the

smaller pipe (the upper one); insert the pipes

from the front, expanding slightly with your hands

so that they can get hooked onto the two

brackets. Fix the pipes to the brackets by means

of the screws D and E.

OPERATION

--------------------------------------------------

A = light switch (Fig. 7).

B = first speed motor ON/OFF switch.

C = second speed switch.

D = third speed switch.

E = warning light: indicates motor operation.

Filtering/ducting conversion:

The conversion can be done in the inside of the

appliance. Access is possible by opening the grille

as described beforehand. Verify that screw A (Fig.

8) is completely unscrewed, so that the inside valve

let the air to be conveyed again into the room throuth

the slots. Insert the activated charcoal fiber panel

(Fig.2F and 8F): lift the two stops made of metallic

wire (Fig. 8C); insert the fiber panel and set back

the two stops.

In case the hood is a filtering version one, it is

necessary to change the activated charcoal fiber

panel (Fig.2F and 8F) according to utilization about

every six month. To remove the fiber panel:

ñ take off the anti-grease grill: by means of the

proper knobs make the grill move towards

the rear of the apparatus and drop the front

part of it; now, keeping the right (or left) side

of the grill steady, make the opposite side

rotate so that it gets off the hood (Fig.3).

ñ lift the two metallic stops (Fig. 8C).

ñ remove the fiber panel.

The anti-grease filtering panel is easily removed

from the grille by opening it as described above

and lifting the two stops made of metallic wire (Fig.

8C). In the filtering version, to get access to the

anti-grease panel the activated charcoal fiber panel

must be removed too. Change the anti-grease panel

according to use. If the panel is a metallic one it can

be washed with some neutral detergent by hand or

in a dish-washer.

To gain access to the light bulb(s), remove the

anti-grease grill as described above and remove

the bulb(s). Replace with lamps of the same type.

A B C D E

Produktspezifikationen

Marke:	Zanussi
Kategorie:	Dunstabzugshaube
Modell:	ZHT61X

Brauchst du Hilfe?

Wenn Sie Hilfe mit Zanussi ZHT61X benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Dunstabzugshaube Zanussi

Zanussi ZHI615G Bedienungsanleitung

3 Oktober 2024

Zanussi ZHC511 Bedienungsanleitung

2 Oktober 2024

Zanussi CWH6065X Bedienungsanleitung

2 Oktober 2024

Zanussi ZH6020B3 Bedienungsanleitung

28 September 2024

Zanussi ZF601 Bedienungsanleitung

21 September 2024

Zanussi ZH6020W/E Bedienungsanleitung

17 September 2024

Zanussi ZHC714 Bedienungsanleitung

10 September 2024

Zanussi ZHC 95 Bedienungsanleitung

5 September 2024

Zanussi ZHC 919 x3 Bedienungsanleitung

3 September 2024

Zanussi NH 9013 x Bedienungsanleitung

2 September 2024

Bedienungsanleitung Dunstabzugshaube

Neueste Bedienungsanleitung für -Kategorien-

Pelgrim ISW990 Bedienungsanleitung

16 Oktober 2024

Amana UVL6048JSS Bedienungsanleitung

16 Oktober 2024

Maytag UVL6048JSS Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GTW Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GW Bedienungsanleitung

16 Oktober 2024

Freggia CHS46GB Bedienungsanleitung

16 Oktober 2024

Freggia CHS46B Bedienungsanleitung

16 Oktober 2024

Freggia CHS45X Bedienungsanleitung

16 Oktober 2024

Freggia CHS45W Bedienungsanleitung

16 Oktober 2024

Freggia CHS45B Bedienungsanleitung

16 Oktober 2024