Wilbur Curtis G4TP 1T Bedienungsanleitung

Wilbur Curtis Kaffeemaschine G4TP 1T

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Wilbur Curtis G4TP 1T (18 Seiten) in der Kategorie Kaffeemaschine. Dieser Bedienungsanleitung war für 34 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/18

This Curtis Generation 4 Unit is Factory Pre-Set and Ready to Go Right from the Box.

Following are the Factory Settings for your G4 Coffee Brewing System:

• Brew Temperature = 200°F • Water Bypass = LARGE & MEDIUM Brew Only

• Brew Volume = Set to Vessel Requirement.

System Requirements:

• Water Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)

• Electrical: See attached schematic for standard model or visit www.wilburcurtis.

com for your model.

Model

G4TP1T

CAUTION: DO NOT

connect this brewer to hot

water. The inlet valve is

not rated for hot water.

CAUTION: Please use

this setup procedure

before attempting to use

this brewer. Failure to follow the

instructions can result in injury or the

voiding of the warranty.

IMPORTANT: Equipment

to be installed to comply

with applicable govern-

mental plumbing/electrical codes

having jurisdiction.

ISO 9001:2008 REGISTERED

WILBUR CURTIS CO., INC.

6913 West Acco Street

Montebello, CA 90640-5403

For the latest information go to

www.wilburcurtis.com

Tel: 800-421-6150

Fax: 323-837-2410 For the latest specications and information go to www.wilburcurtis.com

This equipment is designed for commercial use. Any servicing other than cleaning and routine maintenance

should be performed by an authorized Wilbur Curtis Company Service Technician.

• DO NOT immerse the unit in water or any other liquid

• To reduce the risk of re or electric shock, DO NOT open service panels. There

are no user serviceable parts inside.

• Keep hands and other items away from hot areas of the unit during operation.

• Never clean with scouring powders or harsh chemicals.

Important Safeguards/Symbols

Service Manual – G4 ThermoPro 1 Gallon Twin

W C C ., i .ilbur urtis o nC

Symbols:

WARNINGS – To help avoid personal injury

Important Notes/Cautions – from the factory

Sanitation Requirements

NSF International requires the following water connection:

1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) is required so

that the unit can be moved for cleaning.

2. This unit must be installed with adequate backow protection to comply with applicable federal,

state and local codes.

3. Water pipe connections and xtures directly connected to a portable water supply shall be sized,

installed and maintained in accordance with federal, state, and local codes.

3. Connect the unit to electrical outlet with appropriate amperage rating (see serial tag on machine).

4. Once power has been supplied to the unit, ip the toggle switch to the ‘ON’ position (located on the rear of

the unit), the water tank will begin to ll. When the water level in the tank reaches the probe, the heating

element(s) will turn on.

5. Water in the heating tank will require approximately a half hour before reaching operating temperature

(factory setting of 200°F). Where applicable, turn on the Universal Control Module (UCM). When the unit

reaches operating temperature, it will display “READY TO BREW”.

NOTE: A water ltration system must be used to help maintain trouble-free operation. Air must be

purged from the cartridge prior to connection to equipment. In areas with extremely hard water,

we highly recommend the use of a Curtis approved water lter. For our full line of lters, please log

on to www.wilburcurtis.com.

SETUP STEPS

1. The unit should be level (left to right - front to back), on a secure surface.

2. Connect the water line to the water inlet tting on the rear of the unit. Water volume ow to the machine

should be consistent. Use tubing sized sufciently to provide a minimum ow rate of one gallon per minute.

Your Curtis G4/Gold Cup Series is Factory Pre-Set for Optimum Performance.

After connection to water and power; turn on the brewer at the rear toggle switch. You will hear a beep and the status lights will come on for a moment.

The screen will display . Next is displayed. Water will ll the tank (2-3 minutes depending on water ow rate).

When the proper level is reached will appear on the screen. It takes approximately 30 minutes to reach the set point temperature.

Control will display when temperature reaches the set point. The unit is now ready to brew.

MODEL NUMBER

CONTROL BD NUMBER

READY TO BREW

HEATING

FILLING

1. Brewer should be ON. Conrm this at the toggle switch on the back of the brewer. The touch screen should read Ready to Brew.

2. Place an empty coffee container centered beneath the brew cone.

6. Start the brew cycle by hold your nger

on the desired brew icon. As soon as

you hear the click of the brew valve, the

brew cycle has started and you can lift

your nger.

Brew Code: You may nd that when a brew

button is pressed, a key pad appears on the

screen. This is a brew lock-out feature that

5. Transfer the lled brew cone to the

brewer.

3. Place a new paper lter into the brew

cone.

4. Fill the brew cone with the proper

amount of ground coffee.

COFFEE BREWING INSTRUCTIONS

WARNING – AVOID SCALDING: USE BOTH HANDLES FOR BETTER CONTROL. The brew cone may be lled with hot coffee

grounds and is difcult to manage with one hand.

The coffee vessel is heavy when full. Take precautions to avoid dropping while moving.

requires a code to be entered before a brew

will start. The default is OFF.

CAUTION: When enabled, as soon as you

enter the brew code a brew cycle starts.

Refer to page 8 for more information about the

Brew Code.

During the brew cycle, an animated 1½

gallon server icon will appear on the screen

and a brew timer will count down the time

remaining on the brew cycle.

Touch Screen Control Module

The touch screen turns on when power is available to the controller. The screen will contain standard control feature such as symbols and buttons. Press-

ing these elements with your nger tip will activate the programming functions. The default screen, as well as some added control buttons are shown in the

illustration below.

STATUS LIGHTS

BREW BUTTONS

CURTIS LOGO

TO ENTER PROGRAMMING

Tap Curtis logo 5 times to bring

up the ACCESS CODE screen.

RETURN TO HOME SCROLL RETURN TO PREVIOUSUNDO

CONTROL SYMBOLS

All of these symbols may not

be visible at one time.

MAIN MENU screen contains six control icons: