Whirlpool WWDC 7126 Bedienungsanleitung

Whirlpool Waschmaschine WWDC 7126

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Whirlpool WWDC 7126 (13 Seiten) in der Kategorie Waschmaschine. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/13
a
b
c
1
d
e
f
g
2
3
4
5
6
7
8
9
11
10
13
14
12
EN 1
INTENDED USE
This washing machine is exclusively destined to treat
machine washable laundry in quantities which are
usual for private households.
• Observe the instructions given in these
Instructions for Use and the Programme Chart
when using the washing machine
• Keep these Instructions for Use and the
Programme Chart; if you pass on the washing
machine to another person, also give him/her the
Instructions for Use and the Programme Chart.
SAFETY AND GENERAL RECOMMENDATIONS
1. Safety instructions
• The washing machine is
appropriate for indoor use only.
• Do not store flammable fluids
near the appliance
• Children must not be allowed to
play with the washing machine
or to climb into the drum.
• The washing machine can
be operated by children
from the age of 8 years up,
as well as by people with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge,
provided they are supervised
or instructed regarding the safe
use of the washing machine
and they understand the
dangers resulting from the use.
Children must not play with
the washing machine. Care
and maintenance works on the
washing machine must not be
carried out by children without
being supervised.
• Do not operate the washing
machine at temperatures below
5°C.
• For freestanding models: if you
want to place a dryer on top
of your washing machine, first
contact our After-Sales Service
or your specialist dealer to
verify if this is possible. This
is only admitted if the dryer is
fixed on the washing machine
by using an appropriate
stacking kit available through
our After-Sales Service or your
specialist dealer.
• Do not leave the appliance
plugged in when not in use.
• Turn off the tap when not in
use.
• Before any cleaning and
maintenance switch off the
machine or disconnect it from
the mains supply.
• Never open the door forcibly or
use it as a step.
• If necessary, the power cable
may be replaced with an
identical one obtained from our
After-Sales Service. The power
cable must only be replaced by
a qualified technician or by our
After-Sales Service.
• If your washing machine is a
built-in model:
do not operate it unless it is
built-in
you must not remove the up
cover.
• Children younger than 3 years
should be kept away from the
washing machine, unless they
are continuously supervised.
• The ventilation openings in the
base of the washing machine
must not be obstructed by thick
carpet.
EN 2
• If you want to place the
washing machine on a pedestal
or any raised position, make
sure that this pedestal
is solid enough for the
high weight of the washing
machine
is completely level
is large enough, and that the
surrounding area limits the
washing machine so that it
cannot move out of position
in case of extraordinary
operation conditions.
2. Packing
• The packaging materials are 100% recyclable
and bear the recycling symbol . Adhere to
local regulations when disposing of packaging
material.
3. Disposing of packaging and old
washing machines
• The washing machine is built from reusable
materials. It must be disposed of in compliance
with current local waste disposal regulations.
• Before scrapping, remove all detergent residues
and cut off the power cable so that the washing
machine is made unusable.
• This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE). By
ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product.
• The symbol on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment. Disposal
must be carried out in accordance with local
environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.
4. Frost
• Do not place the washing machine in a room
prone to frost. If you must, make sure that the
washingmachine is completely drained after each
wash:
• Remove inlet hose(s) from water tap and let the
water flow out completely.
• Remove drain hose from siphon or handwash
basin and let the water flow out completely.
• Empty residual water inside the machine by
following the instructions in the chapter “Draining
Residual Water”.
5. EC Declaration of Conformity
• The appliance conforms to the following
European Standards: 2006/95/EC Low Voltage
Directive 2004/108/EC Electromagnetic
Compatibility Directive.
The Manufacturer is not liable for any damage to
laundry resulting from inadequate or incorrect fabric
care instructions which have been provided with the
garment or article.
EN 3
BEFORE USING THE WASHING MACHINE
1. Removing the packaging and
inspection
• After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use the
washing machine. Contact After-Sales Service or
your local retailer.
• Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
• If the appliance was exposed to the cold prior to
delivery, keep it at room temperature for a few
hours before operating.
2. Remove the transport bolts
• The washing machine is fitted with transport
bolts to avoid any possible damage to the interior
during transport. Before using the machine, it is
imperative that the transport bolts are removed.
• After their removal, cover the openings with the 4
enclosed plastic caps.
3. Install the washing machine
• Remove the protective film from the control panel
(if available on your model).
• Move the appliance without lifting it by the
worktop.
• Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
• Make sure that all four feet are stable and resting
on the floor and then check that the washing
machine is perfectly level (use a spirit level).
• In case of wooden or so-called “floating floors”
(for instance certain parquet or laminate floors),
place the appliance on a sheet of plywood at
least 60 x 60 cm wide/deep and at least 3 cm
thick which is secured to the floor.
• Make sure that the ventilation openings in the
base of your washing machine (if available on
your model) are not obstructed by a carpet or
other material.
4. Water inlet
• Connect the water inlet hose(s) to the drinking
water supply in accordance with the regulations
of your local water company.
• For models with one inlet valve: cold water
• For models with two inlet valves: cold AND hot
water, or cold water only (see chapter “Installation
Guide”).
• Water tap: 3/4” threaded hose connector
• Water pressure (flow pressure): 100-1000 kPa
(1-10 bar).
• Use only new hoses to connect the washing
machine to the water supply. Used hoses must
not be used and should be discarded.
• For models with hot fill: the hot water inlet
temperature must not exceed 60°C.
5. Drain
• Firmly connect the drain hose to the siphon, or
another outlet for drain water.
• If the washing machine is connected to an
integrated drainage system, ensure the latter is
equipped with a vent to avoid simultaneous load-
ing and draining of water (siphoning effect).
6. Electrical connection
• Electrical connections must be carried out by
a qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.
• Data regarding voltage, power consumption
andprotection requirements is given on the inside
of the door.
• The appliance must be connected to the mains
by means of a socket with an earth connection
in accordance with current regulations. The
washing machine must be earthed by law. The
manufacturer declines all liability for damage to
property or injury to persons or animals due to
non-compliance with the directions given above.
• Do not use extension leads or multiple sockets.
• Access to the mains plug or disconnection from
the mains supply via a double-pole switch must
be ensured at all times after the installation.
• Do not operate the washing machine if it has
been damaged during transport. Inform the After-
Sales Service.
• Mains cable replacement is only to be carried out
by After-Sales Service.
• When using a residual current circuit breaker
(RCCB), only use a model marked with .
EN 4
DESCRIPTION OF THE WASHING MACHINE
(pict. )1
- Depending on the model
a. Worktop (for freestanding models) /Top cover (for
built-in models)
b. Detergent drawer
c. Control panel
d. Service plate (inside the door)
e. Door
f. Pump access with filter and emergency drain
hose (if available) behind the plinth
g. Adjustable feet
DOOR
• To open the door, hold the door handle and pull
the door.
• Close the door by pressing it without excessive
force until it clicks shut.
BEFORE THE FIRST WASH CYCLE
To remove any residual water used in testing by the
manufacturer, we recommend that you carry out
a short wash cycle without laundry.
1. Open the tap.
2. Close the door.
3. Add a small amount of detergent (maximum
1/3 of the quantity the detergent manufacturer
recommends for lighty soiled laundry) to the main
wash chamber of the detergent dispenser.
4. Select and start programme “Synthetics” at 60°C
(see separate programme chart”).
PREPARATION OF THE LAUNDRY
Sort the laundry
1. Sort the laundry according to…
• Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics, wool,
handwash items.
• Colour
Separate whites and coloureds. Wash new
coloured items separately.
• Size
Wash items of different sizes in the same load to
improve washing efficiency and distribution in the
drum.
• Fabric delicacy
Wash delicate articles separately: use a special
programme for Pure New Wool , curtains and
other delicates. Always remove curtain glides or
wash curtains with the glides inside a cotton bag.
Use the special programme for handwash fabrics.
Wash stockings, belts and other small items or
articles with hooks (e.g. bras) in special cotton
bags for washing machines or in zipped pillow
cases.
2. Empty pockets
Coins, safety pins and similar items can damage
your laundry as well as the washing machine’s
drum and tub.
3. Fasteners
Close zips and fasten buttons or hooks; loose
belts or ribbons should be tied together.
Stain remwoval
• Blood, milk, egg and other organic substances
are generally removed by the enzyme phase of
the programme.
• To remove red wine, coffee, tea, grass and
fruitstains etc. add a stain remover to the main
wash chamber of the detergent dispenser.
• Particularly stubborn stains should be treated
before the wash.
Dyeing and bleaching
• Only use dyes and bleaches that are suitable
forwashing machines.
• Follow the manufacturer’s instructions.
• Plastic and rubber parts of the machine may be
stained by dyes or bleaches.
Loading the laundry
1. Open the door.
2. Load the articles one at a time loosely into the
drum, without overfilling. Observe the load sizes
given in the programme chart (overloading the
machine will result in unsatisfactory washing
results and creased laundry).
3. Close the door. Take care that no laundry gets
stuck between door and door seal.
EN 5
DETERGENTS AND ADDITIVES
Keep detergents and additives in a safe, dry
place out of the reach of children.
Do not use any solvents (e.g. turpentine,
benzene); do not machine wash fabrics that
have been treated with solvents or flammable
liquids.
Only use detergents and/or additives that are
specifically produced for domestic washing
machines. Observe the recommendations on the
care labels of your laundry.
The choice of detergent depends on:
• Type of fabric
• Colour
• Recommended wash temperature
• Degree and type of soiling
Laundry type Kind of detergent
White robust laundry
(cold-95°C):
heavy duty detergents with
bleach
White delicate laundry
(cold-40°C): mild detergents with bleach
and/or optical brighteners
Light /pastel- shaded
colours (cold-60°C): detergents with bleach and/
or optical brighteners
Intensive colours
(cold-60°C): colour detergents without
bleach/optical brighteners
Black/dark
colours(cold-60°C): special detergents for black/
dark laundry
For laundry requiring special treatment (e.g. wool
or microfibers), we recommend to use specialized
detergents, additives or pre-treatment available on
the market.
Refer to internet link www.cleanright.eu for more
detailed information.
Do not use liquid detergent for the main wash
when having activated the “Prewash” option.
Do not use liquid detergent when selecting a
later cycle start / cycle end (depending on the
model).
Dosage
Follow the dosage recommendations on the
detergent pack. They depend on:
• degree and type of soiling
• size of wash
full load: follow the detergent manufacturer’s
instructions;
half load: 3/4 the amount used for a full load;
minimum load (about 1 kg): half the amount
used for a full load;
If there is no reference to a certain wash load on
the detergent pack: the detergent manufacturers
usually refer their dosing recommendations to 4.5
kg laundry for heavy duty detergent and 2.5 kg
laundry for delicate detergent.
• water hardness in your area (ask for information
from your water company). Soft water requires
less detergent than hard water.
Please note:
Too much detergent can result in excess foam
formation, which reduces washing efficiency. If the
washing machine detects too much foam, it may
prevent spinning, or prolong the programme duration
and increase the water consumption (see also
remarks on foam formation in the “Troubleshooting
Guide”). Insufficient detergent may result in grey
laundry and also calcifies the heating system, drum
and hoses.
Where to put detergents and additives
(pict. ) 2
Prewash chamber
• Detergent for the prewash phase (only if you
have activated “prewash” option)
Main wash chamber
• Detergent for the main wash phase (must be
added for all wash programmes)
• Additive for stain removal (optional)
• Water softener (optional; recommendable for
water hardness class 4 or more)
Softener chamber
• Fabric softener (optional)
• Starch dissolved in water (optional)
Do not exceed the “MAX” level mark when filling in
detergent, additives or softener.
If you use liquid detergent, close the dispenser right
after having filled in the detergent.
For more information regarding the application of
detergent and fabric softener in the programmes,
have a look at the separate program chart.
Using chlorine bleach
• Wash your laundry in the desired programme
(Cotton, Synthetics), adding an appropriate amount
of chlorine bleach to the SOFTENER chamber
(close the lid carefully).
• Immediately after end of programme, start the
“Rinse and Spin” programme to eliminate any
residual bleach smell; if you want, you can add
softener.
• Never put both chlorine bleach and softener into
the softener chamber at the same time.
• Prefer to use bleaches on oxygen basis; in this
case follow the instructions of the manufacturer.
Using starch powder
• Select the “Rinse and Spin” programme and check
that the spin speed is adjusted to not more than
800 rpm.
• Start the programme, pull out the detergent dis-
penser so that you can see approximately 3 cm of
the softener chamber.
• Pour the starch solution prepared into the softener
chamber while the water is running into the deter-
gent dispenser.
EN 6
CLEANING THE FILTER/ DRAINING RESIDUAL WATER
We recommend that you check and clean the filter
regularly, at least two or three times a year, especially:
• If the “Clean pump” indication lights up.
• If the appliance is not draining properly or if it fails
to perform spin cycles.
• If the washing machine stands in a room prone to
frost, you have to drain residual water after each
wash to avoid damages.
IMPORTANT: make sure the water has cooled
before draining the appliance.
1. Stop the appliance and unplug it.
2. To open the plinth (depending on the model):
Push down the tabs right and left (if available) to
release the plinth and remove it (pict. ).3
Remove the plinth by using the siphon inset of
the detergent dispenser: push downwards one
side of the plinth with your hand, then push the
siphon inset into the gap between plinth and
front panel and pry open the plinth (pict. 4).
For built-in models: unclip the kitchen plinth and
remove it.
3. Place a container near the washing machine.
4. If your washing machine has an emergency drain
hose: Unclip the emergency drain hose, or pull
out the emergency drain hose from the washing
machine’s base (depending on the model).
If there is no emergency drain hose: place a broad,
flat container beneath the filter (pict. ). Ignore 6
steps 5 - 8 and proceed with 9.
5. Hold the emergency hose’s end into the container
and remove the stopper (pict. ).5
6. Wait until all the water has drained, then refix the
stopper at the hose’s end (pict. ).7
7. Refix the emergency drain hose to the clip, or
push it back into the washing machine’s base
(depending on the model).
8. Lay an absorbable cotton cloth (e.g. a towel) on
the floor in front of the filter.
9. Slowly open the filter by turning it counter-clockwise
(pict. ); wait until all the water has drained, then 8
unscrew the filter completely and remove it.
10. Only for cleaning the filter: clean the filter and the
filter chamber; check that the pump rotor in the
filter chamber moves freely.
11. Re-insert the filter and screw it in clockwise as far
as it will go.
12. Pour about 1 litre of water into the detergent
dispenser to reactivate the “Eco system”. Check
that the filter is inserted properly and securely and
no water comes out.
13. Reinstall the plinth (pict. ); if necessary, tilt the 9
washing machine slightly backwards for doing that
(a second person must help you).
For built-in models: reinstall the kitchen plinth.
14. Plug in the washing machine. It is now ready for
operation again.
CARE AND MAINTENANCE
Always unplug the washing machine before doing any maintenance.
Cleaning the detergent dispenser
1. Pull out the dispenser drawer until it stops. Press
with your finger on the small depression over the
“PUSH” marking (pict. ) to release the drawer 10
and pull it out completely.
2. Remove the siphon from the softener chamber by
pulling it upwards (pict. ).11
3. Wash all the parts under running water.
4. Clean the dispenser compartment with a damp
cloth.
5. Refit the siphon in the softener chamber by push-
ing it down until it stops; then push the dispenser
drawer back into the dispenser compartment.
Water inlet hose (pict. or , depending 12, 13 14
on model)
Check the inlet hose regularly for brittleness and
cracks and replace it if necessary using a new hose of
the same type.
The inlet hose as shown on picture has a safety 13
valve to prevent the appliance against uncontrolled
water inlet; if the safety valve inspection window ( ) is A
red, the safety valve has been activated and the hose
must be exchanged. Contact out After-Sales Service
or your specialist dealer to obtain a new inlet hose.
For unscrewing the inlet hose as shown on picture , 13
you must push down the release lever ( - if available) B
while unscrewing it.
If your inlet hose has a transparent hose coating (pict.
14), periodically check the colour of the transparent
coating.
If the transparent hose shows a local dark colour
change, this is an indication that the hose may have a
leak and should be replaced.
Contact our After-Sales Service team or specialist
dealer to obtain a replacement hose.
Cleaning the mesh filter in the water inlet
hose
1. Close the tap and loosen the inlet hose on the tap.
2. Clean the internal mesh filter and screw the water
inlet hose back onto the tap.
3. Now unscrew the inlet hose on the rear of the
washing machine.
4. Pull off the mesh filter from the washing machine
connection with universal pliers and clean it.
5. Refit the mesh filter and screw the inlet hose on
again.
6. Turn on the tap and ensure that the connections
are completely water-tight.
Appliance exterior and control panel
• Wash down with a soft damp cloth. Dry with a soft
cloth.
Appliance interior
• After each washing, leave the door open for some-
time to allow the inside of the appliance to dry.
• If you never or seldom wash your laundry at 95°C,
we recommend to occasionally run a 95°C pro-
gramme without laundry, adding a small amount
of detergent, to keep the interior of the appliance
clean.
EN 7
Door seal
• Dry the door seal after each washing with an
absorbent cotton cloth; make sure that the door
seal is completely dry before closing the door of
the empty washing machine.
• Check the condition of the door seal periodically.
Filter
• Check and clean the filter regularly, at least two or
three times a year (see “Draining Residual Water/
Cleaning The Filter”).
Do not use detergents containing solvents,
scouring powder, glass or general purpose
cleaners, and flammable fluids. They may harm the
plastic surfaces or other parts.
REMAINING MOISTURE CONTENT OF THE LAUNDRY
AFTER SPINNING
The degree of moisture remaining in the laundry
after spinning mainly depends on the fabric type, the
selected programme and spin speed.
The lowest remaining moisture content can be
achieved using the wash programme referred to by
the Energy Label, with maximum spin speed. This
programme is marked in the separate programme
chart as “Reference programme for the Energy Label”.
Below a survey of the remaining moisture content
(in %) related to the various spin-drying efficiency
classes.
TRANSPORT AND HANDLING
Never lift the appliance by the worktop (if available)
when transporting.
1. Pull out the mains plug.
2. Turn off the tap.
3. Check that machine door and detergent dispenser
are properly closed.
4. Disconnect the inlet and drain hoses.
5. Eliminate all water from the hoses and from the
appliance (see “Draining Residual Water/Cleaning
The Filter”).
6. Fit the transport bolts (obligatory).
ACCESSORIES
For some freestanding models, you can obtain via our
After-Sales Service or your specialist dealer:
• Pedestal DrawerA which can be installed
beneath your washing machine. It raises your
machine to allow for more comfortable loading and
unloading, as you now no longer need to bend as
far to access the unit. Furthermore, it offers a great
space-management tool and storage solution.
• Stacking KitA , by which your dryer can be fixed
on top of your washing machine.
• Stacking Kit ShelfA , by which your dryer can
be fixed on top of your washing machine to save
space and to facilitate loading and unloading your
dryer in that high position.
• Cover Panel KitA , by which your washing
machine can be built under a continuous kitchen
worktop, for example. Check with our After-Sales
Service or your specialist dealer if this is possible
for your washing machine model.
AFTER-SALES SERVICE
Before contacting After-Sales Service:
1. Try to remedy the problem yourself (see
“Troubleshooting Guide”).
2. Restart the programme to check whether the
problem has solved itself.
3. If the washing machine continues to function
incorrectly, call After-Sales Service.
Specify:
• The nature of the problem.
• The exact model of the washing machine.
• The service code (number after the word
SERVICE).
The After-Sales Service sticker can be found
inside the door.
• Your full address.
• Your telephone number and area code. As a
priority, you should contact the After-Sales Service
of the retailer who supplied you with the washing
machine.
Manufacturer:
Whirlpool Europe s.r.l. - Socio Unico
Viale Guido Borghi 27
21025 Comerio (Varese)
Italy
Spin-drying
efficiency class
Remaining moisture
content in %
A (= most efficient) less than 45
B 45 or more, but less than 54
C 54 or more, but less than 63
D 63 or more, but less than 72
E 72 or more, but less than 81
EN 8
TROUBLESHOOTING GUIDE
Your washing machine is equipped with automatic safety functions which detect and diagnose faults at
an early stage and allow you to react appropriately. These faults are frequently so minor that they can be
removed within a few minutes.
Problem Causes - Solutions - Tips
Appliance does not start,
no indicators are on
• Plug is not properly inserted in socket.
• Socket or fuse does not function correctly (use a table lamp or similar
appliance to test it).
• The washing machine is switched off automatically to save energy,
before programme start or after programme end. To switch on the
washing machine, turn the programme selector first to “Off/O” and then
to the desired programme again.
Appliance does not start
although “Start(Pause)”
has been pressed
• Door is not properly closed.
• The “Child lock/Lock buttons” feature has been activated (if
available on your model). To unlock the buttons, push the two buttons
marked with the key symbol simultaneously and hold them at least for 3
seconds. The key symbol on the display disappears and the programme
can be started.
Appliance stops during the
programme, and the
“Start(Pause)” indicator
blinks
• “Rinse hold” is activated. Press “ ” to spin the laundry. Start(Pause)
For draining the water without spinning, select “Drain” programme (if
available) or press the “Reset/Drain” button for at least 3 seconds.
• Programme has been changed - reselect desired programme and press
“ ”.Start/Pause
• Programme has been interrupted and eventually door has been opened
- close door and restart programme by pressing “Start(Pause)”.
• The appliance’s safety system has been activated (see “Failure
indicators” in your programme chart).
• Water tap is not opened or water inlet hose is kinked or blocked (“Water
tap closed” indicator blinks).
Detergent dispenser
contains residues from
detergent and/or additives
• Water entering is not enough; the mesh filters of the water supply could
be blocked (see “Care And Maintenance”).
Appliance vibrates during
spin cycle
• Transport bolts have not been removed; before using the machine, it
is imperative that the transport bolts are removed.
• Appliance is not level / not standing firmly on all four feet (see separate
“Installation Guide”).
Final spin results are poor • Unbalance during spinning prevented spin phase to protect the washing
machine (see “Unbalance during spinning”).
• Excessive foam formation prevented spinning; select and start “Rinse &
Spin” programme. Avoid excessive detergent dosing (see “Detergents
And Additives”).
• “Spin” button has been set to a low spin speed.
Unbalance during spinning”
The “Spin/Drain” indicator
in the programme flow bar
blinks, or the spin speed on
the display blinks, or the spin
speed indicator blinks after
the end of the programme
(depending on the model).
The laundry is still very wet.
Unbalance of the laundry load during spinning prevented the spin phase
to avoid damages on the washing machine. This is why the laundry is still
very wet.
Reason for unbalance can be: small laundry loads (consisting of only few
quite big or absorbent items, e.g. towels), or big/heavy laundry items.
• If possible avoid small laundry loads.
• It is highly recommended that you add other laundry items of different-
sizes when washing a big or heavy piece of laundry.
If you want to spin the wet laundry, add more laundry items of different
sizes, and subsequently select and start the “Rinse & Spin” programme.
The washing machine is at a
standstill for several minutes
in the middle of a running
programme; the wash
programme seems not to
proceed
Normal function of the washing machine used for optimizing the rinse
phase. One reason for such a pause can be that you might have used too
much detergent; the washing machine automatically interrupts the pro-
gramme to have the foam reduced. This standstill may be repeated several
times until the foam reduction is sufficient to continue the wash cycle. If the
foam persists, the red “Service” indicator will light up and the display shows
“F18” or “Fod” - refer to the instructions concerning the “Service” indication
on the next pages in this case.
EN 9
Problem Causes - Solutions - Tips
Detergent residues
on laundry after wash
Whitish residues on dark fabrics are caused by insoluble compounds used in
phosphate-free powder detergents:
avoid overdosing of detergent; use liquid detergent; select “Intensive Rinse” op-
tion if possible; brush out the fabric.
Programme duration
is considerably
longer or shorter
as indicated in the
“programme chart”
or on the display (if
available)
Normal function of the washing machine to adapt to factors that can have an
effect on the programme duration, like excessive foam formation, load unbalance
due to heavy laundry items, prolonged heating time resulting from low inlet water
temperature etc. Moreover, the sensing system of the washing machine adapts the
programme duration to the size of the wash load.
Depending on these factors, the duration is recalculated during the
programme and updated if necessary; during such periods, an animation
appears on the display (if available). For small loads, the programme time
indicated in the “programme chart” may be reduced by up to 50%.
Description of failure indicators
Failure
indicator blinks
Indication on display
(if available) Description - Causes - Solutions
“Service”
from “ ” to “ ”F03 F43
(except “ ” and “ ”)F18 F24
“Electrical module fault”
Push the “Reset” button for at least 3 seconds.
“ ”F24 May appear for very water-soaking laundry, or if you
added too much laundry for a programme destined for
small loads only. Do not overload the washing ma-
chine. Push the “Reset” button for at least 3 seconds
to stop the programme. Select and start “Rinse and
Spin” programme to complete the interrupted wash
programme properly.
“ ” or “ ”F02 FA “Waterstop fault”
Turn the programme selector to the “Off/O” position,
pull out the mains plug and turn the water tap off.
Then:
• Plug in the appliance again.
• Turn the water tap on (if water immediately flows
into the appliance without the appliance being
started, there is a failure; turn off the tap and notify
the After-Sales Service).
• Select and start the desired programme again.
“ ” or “ ”F18 Fod “Overfoaming”
Too much foam interrupted the wash programme.
If your washing machine has a “Dosing Aid” function,
and you used it: check if the dosing values set for the
different programme groups correspond to the dosing
values recommended for the detergents you use (see
details in separate Instructions for the “Dosing Aid”).
• Select and start the “Rinse & Spin” programme.
• Afterwards select and start the desired programme
again, using less detergent. See also paragraph
“The machine is at a standstill....” on first page of
Troubleshooting Guide.
EN 10
Failure
indicator blinks Description - Causes - Solutions
“Water tap closed”
Appliance has no or insufficient water supply. The “ ” light blinks.Start(Pause)
Check whether:
• Water tap is fully open and water supply pressure is sufficient.
• Kinks are present in the water inlet hose.
• Mesh filter of water inlet hose is blocked (see “Care and Maintenance”.
• The water hose is frozen up.
• The safety valve inspection window of your water inlet hose is red (provided
your appliance has a water supply hose as shown on picture - see chapter “13”
“Care And Maintenance”); replace the hose by a new one available through our
After-Sales Service or your specialist dealer.
After problem has been removed, restart programme by pressing “ ”.Start(Pause)
If the fault occurs again, contact our After-Sales Service.
“Clean pump”
Waste water is not pumped out. The appliance stops in the corresponding
programme step; unplug it and check whether:
• Kinks are present in the drain hose, or the hose is blocked for another reason.
• Filter or pump is blocked (see chapter “Draining Residual Water/Cleaning The
Filter”); ).make sure the water has cooled before draining the appliance
• The drain hose is frozen up.
After problem has been removed, push the “Reset” button for at least 3 seconds;
afterwards restart the desired programme. If the fault occurs again, contact our
After-Sales-Service.
If your washing machine has no display, check which of the previously described situations could be
the origin of the fault and follow the corresponding instructions.
ELECTRICAL CONNECTION
For Great Britain only
Warning - this appliance must be earthed.
Fuse replacement
If the mains lead of this appliance is fitted with a BS
1363A 13amp fused plug, to change a fuse in this
type of plug use an A.S.T.A. approved fuse to BS
1362 type and proceed as follows:
1. Remove the fuse cover ( ) and fuse ( ).A B
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse
and if the fuse cover is lost the plug must not be used
until a correct replacement is fitted.
Correct replacement are identified by the colour insert
or the colour embossed in words on the base of the
plug. Replacement fuse covers are available from your
local electrical store.
For the Republic of Ireland only
The information given in respect of Great Britain will
frequently apply, but a third type of plug and socket is
also used, the 2-pin, side earth type.
Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet,
Please contact After-Sales service for further
instruction.
Please do not attempt to change plug yourself. This
procedure needs to be carried out by a qualified
technician in compliance with the manufactures
instructions and current standard safety regulations.

Produktspezifikationen

Marke: Whirlpool
Kategorie: Waschmaschine
Modell: WWDC 7126

Brauchst du Hilfe?

Wenn Sie Hilfe mit Whirlpool WWDC 7126 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Waschmaschine Whirlpool

Whirlpool

Whirlpool WFW9250WR Bedienungsanleitung

10 Oktober 2024
Whirlpool

Whirlpool LA5430XP Bedienungsanleitung

8 Oktober 2024
Whirlpool

Whirlpool BI WDWG 961484 Bedienungsanleitung

7 Oktober 2024
Whirlpool

Whirlpool WFW862CHC Bedienungsanleitung

5 Oktober 2024
Whirlpool

Whirlpool WB10037 Bedienungsanleitung

4 Oktober 2024
Whirlpool

Whirlpool WFE1075BD Bedienungsanleitung

3 Oktober 2024
Whirlpool

Whirlpool LA5200XT Bedienungsanleitung

3 Oktober 2024
Whirlpool

Whirlpool SF FWG 81296WS Bedienungsanleitung

3 Oktober 2024
Whirlpool

Whirlpool LA5500XT Bedienungsanleitung

3 Oktober 2024
Whirlpool

Whirlpool WFW5720RW Bedienungsanleitung

2 Oktober 2024

Bedienungsanleitung Waschmaschine

Neueste Bedienungsanleitung für -Kategorien-

BEKO

BEKO BWT584BF Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO WTE1014XW Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO BM3WFU39412CW Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO BM3WFU37412CW Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO WTIK74122 Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO BM1WT3921W Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO B5D510645UW Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO BM1WT3821W Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO LWI284410 Bedienungsanleitung

4 Dezember 2024
BEKO

BEKO BM1WT3721W Bedienungsanleitung

4 Dezember 2024