Whirlpool WDT975SAHV Bedienungsanleitung


Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Whirlpool WDT975SAHV (2 Seiten) in der Kategorie SpĆ¼lmaschine. Dieser Bedienungsanleitung war fĆ¼r 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
DRAIN REQUIREMENTS
ā– 
A new drain hose is supplied with your dishwasher.
If drain hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current AHAM/
IAPMO test standards, is resistant to heat and detergent, and
ļ¬ts the 1" (25 mm) drain connector of the dishwasher.
NOTE: Do not connect multiple drain hoses together.
ā– Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20" (508 mm)
minimum above the ļ¬‚oor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
ā– Make sure to use an air gap if the drain hose is connected
to house plumbing lower than 20" (508 mm) above
subļ¬‚oor or ļ¬‚oor.
ā– 
If required, the air gap should be installed in accordance
with the air gap installation instructions. When you are
connecting the air gap, a rubber hose (not provided) will
be needed to connect to the waste tee or disposer inlet.
ā– Use 1/2" minimum I.D. drain line ļ¬ttings.
Use of air gap
Air gap
Undercounter Dishwasher
WATER SUPPLY REQUIREMENTS
ā– This dishwasher has a water heating feature and also
requires a connection to a hot water supply line.
ā– A hot water line with 20 to 120 psi (138 to 862 kPa)
water pressure can be veriļ¬ed by a licensed plumber.
ā– 120Ā°F (49Ā°C) water at dishwasher
ā– 3/8" O.D. copper tubing with compression ļ¬tting or ļ¬‚exible
braided water supply line. See the ā€œTools and Partsā€ section
at the front of the guide for part details and orders.
NOTE: 1/2" minimum plastic tubing is not recommended.
ā– A 90Ā° elbow with 3/4" hose connection with rubber washer.
ā– Do not solder within 6" (152 mm) of the water inlet valve.
ā– If installed in new construction, make sure the house
water supply lines have been ļ¬‚ushed prior to connecting
the dishwasher to remove any debris that may exist in
the supply line.
NOTE: If replacing an existing dishwasher, it is recommended
to install a new water line (see the ā€œTools and Partsā€ section at
the front of the guide for part details) and drain hose (supplied)
with the new dishwasher.
ELECTRICAL REQUIREMENTS
ā– 
120-volt, 60 Hz, AC-only, 15- or 20-amp, fused
electrical supply
ā– Copper wire only
ā– A maximum of 2 ļ¬eld wiring supply conductors
(12 AWG largest size) plus 1 grounding conductor
are permitted in the terminal box.
We Recommend:
ā– 
A time-delay fuse or circuit breaker
ā– A separate circuit
If Connecting Dishwasher with a Power Cord:
ā– Use UL Listed power cord kit marked for
use with dishwasher. See the ā€œTools and
Partsā€ section at the front of the guide for
part details and orders.
ā– 
Plug into a grounded 3 prong outlet. Outlet must
meet all local codes and ordinances.
If Connecting Dishwasher with Direct Wiring:
ā– Use ļ¬‚exible, armored, or nonmetallic
sheathed copper wire with grounding
wire that meets the wiring requirements
for your home and local codes and ordinances.
ā– 
Use a UL Listed/CSA Approved metallic strain relief.
See the ā€œTools and Partsā€ section at the front of the
guide for part details and orders.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
speciļ¬cations without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Speciļ¬cations subject to
change without notice.
Page 1 of 2
W10806906-D-WH
11/16
PRODUCT MODEL NUMBERS
WDF560SAF
WDF760SAD
WDF770SAF
WDT750SAH
WDT755SAH
WDT780SAE
WDT920SAD
WDT970SAH
WDT975SAH
WDT995SAF
WDTA50SAH
WDTA55SAH
WDTA75SAH
Product and Cabinet Opening Dimensions
237/ "8
(606 mm)
30"
(762 mm)
31/ " - 421/ "2
(88 mm - 106 mm)
331/ "2
(851 mm)
min. with
wheels
removed
241/ "2
(622 mm)
B
3/ "4
(19 mm)
A
30"
(762 mm)
33/ "4
(94 mm)
21"
(533 mm)
C
24"
(620 mm)
E
24"
(620 mm)
34"
(864 mm)
D
3"
(76 mm)
13/ "4
(44 mm)
63/ "4
(172 mm)
21/ "4
(64 mm)
21/ "4
(64 mm)
2"
(51 mm)
61
/ "4
(159 mm)
101/ "2
(267 mm)
4"
(102 mm)
A. Insulation may be compressed (not used on all models).
B. For panel-ready models, dishwasher depth is 24" (610 mm),
not including the 3/4" (19 mm) custom door panel.
C. Door handles may protrude forward of the face of the
dishwasher, varies by model.
For 4" (100 mm) toe kick, height of cabinet opening is 341/2" (863 mm).
Check that all surfaces have no protrusions
that would prohibit dishwasher installation.
D. Measured from the lowest point on the underside
of the countertop. May be reduced to 33
1/2"
(851 mm) by removing the wheels and perforated
area of insulation (blanket) on dishwasher.
E. Minimum, measured from narrowest point
of opening
NOTE: Shaded areas
of cabinet walls
show where utility
connections may
be installed.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
speciļ¬cations without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Speciļ¬cations subject to
change without notice.
Page 2 of 2
W10806906-D-WH
11/16


Produktspezifikationen

Marke: Whirlpool
Kategorie: SpĆ¼lmaschine
Modell: WDT975SAHV

Brauchst du Hilfe?

Wenn Sie Hilfe mit Whirlpool WDT975SAHV benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung SpĆ¼lmaschine Whirlpool

Bedienungsanleitung SpĆ¼lmaschine

Neueste Bedienungsanleitung fĆ¼r -Kategorien-